Használati útmutató Soundcraft Vi Dante

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Soundcraft Vi Dante (10 oldal) a Staafmixer kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/10
ViDANTETM   Card User & Setup Guide
TheSoundcraft®Vi ViDANTE™ 64 64card is a  xinterfacebetweena 
series console and any Dante compatible device from Harman  or
other 3 rd   party manufacturer.  The card is available in two versions:
Local format) Rack/CSB (D21m3U andViStagebox(6Uformat).Note
thattheStageboxversionisan andIOcardonly does  not allow youto
connect a StageboxtotheconsoleusingDanteinsteadofMADI.
Dante provides network that a digital audio uses standard  Internet
Protocols over both100Mbps and 1Gigabit Ethernet.Danteuses
audio standardsindependent, high accuracy  networksynchronization 
toensureall allDantedevicesare synchronized at  times. Danteruns
on standard and computer networking hardware, does not  require
dedicatednetworkinfrastructure.
TheAudinate VirtualDante Soundcardsoftwareallowsconnectionof
a a network.PC/Macto Danteaudio Thissystemallowsthecomputer
to to the record and from playback Dante network using  most
common VirtualDAWpackages.Dante SoundcardusestheEthernet
port on the computer to communicate with the Dante network;  no
special hardware is required installing other than Dante Virtual
Soundcardsoftware.OneDVSlicensetoken is providedFOCwiththe
card,thislicensecanonlybeinstalledononespecificcomputer.
Additional information abouttheDANTEsystemincludingthelatest
softwareset toolsupand maybefoundontheAudinate®website
http://www.audinate.com/
ViDanteCardUser & SetupGuideV1.3
ConfiguringTheDanteCard
In a mannersimilartoCobraNet™,patchingontheconsolemakes a connectionbetweenconsoleI/O
slotchannels betweenandupto64channelsontheDante Connectionscard.  the areDantecards set
using a tool,inthiscasethe   Dante Controller software from Audinate®. As communication across the
Dante   network is essentially betweennamed cards andchannels the configuration must be correct
to toensurecardstalk listenand  the thecorrect/desiredchannelson Dantenetwork.
Thisuserguidesummarisestheprocessandprovides a simpleworkedexample; full setupdetailsand
configuration downloadabletoolsare fromtheAudinatewebsitewww.audinate.com.
Inadditionit is necessarytosetthe theclockstatusoftheDante card bothwithin networkandin
relation consoleto the  hardware.This  is described below.
ChannelCountSetup
TheDante default,carduses64 64 in and outchannelsby but becan restrictedtouselessinputor
outputchannelsif inrequired. consolesThismaybenecessaryonVi ordertoavoidexceedingthe
192in/192out channel limit of the local rack (or the 64in/64out channel limit if fitted in a Vi or
CompactStagebox).Forexample,if card,onlyoutput arechannels requiredontheDante theinput
channelscanbesetto0,tomaximisethenumberofinputchannelsavailablefor other cards.
TheDIPswitchS1ontheDantecardmainPCB is usedtosettheinputandoutputchannelcount,in
steps pageof on8chsfrom ‐0 64channels.Refer theto diagram thenext whichshowsthelocationof
the channel count DIP switch S1 and the factory default setup of 64 in/64 out. To create other
channel settingscount that   are not marked on the switch, add any two or 3 switch settings together,
ietoselect48chs,the32and16switchesshouldbemoveddowntotheselectedposition.Notethe
maximum countchannel (inputoroutput) is 64andminimum is zero.
SyncSetup
The Dante card can act as either a main clock source for the Dante network, or as a synchronised
clock.Ifthere  is only one console on the network, this will generally be set as the main clock
source  for the network,butincaseswith morethanoneconsole, or whereanotherdeviceacts as
the themain source clock, it willbenecessarytoset console'sDante card tobe asynchronised clock.
TheDante Danteclock sync statusissetupusing Controllersoftware(seelater in in thisguide),but 
addition Dantetothe clocksetup, hasthecard'sclock consolestatuswithinthe  tobeset.This is done
usingaDIPswitchS2on the Dante card main PCB. Refer to the diagram on the next page for the
locationandsettingofthisswitch.
MIX: Select     this position to make the Dante module lock to the console's  internal Wordclock, only
to the be used when the Dante card is set as Preferred Master for the Dante network.
Thissettingisthefactorydefault.
CARD: Selectthispositionto the to tomake consolelock theDantenetworkclock, beusedwhen
the Dante card is synchronised to the network. Note: In this case, a BNC wordclock cable must
also be connected from the Wordclock Out BNC connector on the Dante card, to the  console's
WordclockIN.
Notethat  it is alsonecessaryto thesetuptheclockingschemeof Dantenetworkcorrectly,toavoid
audioclicksanddropouts,pleaserefertothesectiontitledDeviceStatusand ClockStatus inthe
followingpages.
ViDanteCardUser & SetupGuideV1.3
ViDanteCardUser & SetupGuideV1.3
DIPswitchesS1 S2 &LocationDiagram
Refertothepreviouspageforinformationon ofthefunction theseswitches.
Note! pointSwitches  down to select channel count
ignorethe‘ON’legendonswitchbody!
Diagramshowsthedefaultsettingof64in / 64out

Termékspecifikációk

Márka: Soundcraft
Kategória: Staafmixer
Modell: Vi Dante

Szüksége van segítségre?

Ha segítségre van szüksége Soundcraft Vi Dante, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Staafmixer Soundcraft

Útmutatók Staafmixer

Legújabb útmutatók Staafmixer