Használati útmutató Sony Trimaster BVM-E251

Sony hangszóró Trimaster BVM-E251

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Sony Trimaster BVM-E251 (107 oldal) a hangszóró kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/107
4-688-645-13(1)
Professional
Video Monitor
Operating Instructions
Before operating the unit, please read this manual thoroughly
and retain it for future reference.
BVM-E251
BVM-E171
Software Version 1.2
© 2016 Sony Corporation
2
Owner’s Record
The model and serial numbers are located at the rear.
Record these numbers in the spaces provided below.
Refer to these numbers whenever you call upon your
Sony dealer regarding this product.
Model No.
Serial No.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
WARNING
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
THIS APPARATUS MUST BE EARTHED.
WARNING
When installing the unit, incorporate a readily accessible
disconnect device in the fixed wiring, or connect the
power plug to an easily accessible socket-outlet near the
unit. If a fault should occur during operation of the unit,
operate the disconnect device to switch the power supply
off, or disconnect the power plug.
WARNING
The apparatus shall not be exposed to dripping or
splashing. No objects filled with liquids, such as vases,
shall be placed on the apparatus.
CAUTION
The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even
if the unit itself has been turned off.
CAUTION
This equipment is not suitable for use in locations where
children are likely to be present.
BVM-E251 only
When installing the installation space must be secured
in consideration of the ventilation and service operation.
Do not block the ventilation slots, and vents of the
fans.
Leave a space around the unit for ventilation.
Leave more than 40 cm of space in the rear of the unit
to secure the operation area.
When the unit is installed on the desk or the like, leave at
least 1U (4.4cm) or more of space above and below the
Important Safety Instructions
This symbol is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
This symbol is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions
in the literature accompanying the
appliance.
3
unit. Leaving 40 cm or more of space above the unit is
recommended for service operation.
BVM-E171 only
Attention-when the product is installed in Rack:
1.Prevention against overloading of branch circuit
When this product is installed in a rack and is supplied
power from an outlet on the rack, please make sure that
the rack does not overload the supply circuit.
2.Providing protective earth
When this product is installed in a rack and is supplied
power from an outlet on the rack, please confirm that the
outlet is provided with a suitable protective earth
connection.
3.Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the rack
is within the specified limit of this product.
4.Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous condition
due to uneven mechanical loading.
5.Install the equipment while taking the operating
temperature of the equipment into
consideration
For the operating temperature of the equipment, refer to
the specifications of the Operation Manual.
6.When performing the installation, keep the
following space away from walls in order to
obtain proper exhaust and radiation of heat.
Lower, Upper : 4.4 cm (1 3/4 inches) or more
Right, Left : 1.0 cm (13/32 inches) or more
The ventilation should not be impeded by covering the
ventilation openings with items, such as newspapers,
table-cloths, curtains, etc.
No naked flame sources, such as lighted candles, should
be placed on the apparatus.
WARNING: THIS WARNING IS APPLICABLE FOR
USA ONLY.
If used in USA, use the UL LISTED power cord specified
below.
DO NOT USE ANY OTHER POWER CORD.
Plug Cap Parallel blade with ground pin
(NEMA 5-15P Configuration)
Cord Type SJT or SVT, three 16 or 18 AWG wires
Length Minimum 1.5 m (4 ft 11 in), Less than 2.5 m
(8 ft 3 in)
Rating Minimum 10A, 125V
Using this unit at a voltage other than 120V may require
the use of a different line cord or attachment plug, or
both. To reduce the risk of fire or electric shock, refer
servicing to qualified service personnel.
WARNING: THIS WARNING IS APPLICABLE FOR
OTHER COUNTRIES.
1. Use the approved Power Cord (3-core mains lead) /
Appliance Connector / Plug with earthing-contacts
that conforms to the safety regulations of each
country if applicable.
2. Use the Power Cord (3-core mains lead) / Appliance
Connector / Plug conforming to the proper ratings
(Voltage, Ampere).
If you have questions on the use of the above Power Cord
/ Appliance Connector / Plug, please consult a qualified
service personnel.
For the customers in the U.S.A.
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
All interface cables used to connect peripherals must be
shielded in order to comply with the limits for a digital
device pursuant to Subpart B of part 15 of FCC Rules.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
For the customers in Canada
CAN ICES-3 (A)/NMB-3(A)
For the customers in Europe
This product is intended for use in the following
Electromagnetic Environment: E4 (controlled EMC
environment, ex. TV studio).
This apparatus shall not be used in the residential area.
4
For the customers in Europe, Australia and New
Zealand
WARNING
This equipment is compliant with Class A of CISPR 32.
In a residential environment this equipment may cause
radio interference.
Disposal of Old Electrical & Electronic Equipment
(Applicable in Republic of India)
This symbol and its variations indicate that this product
and its components, consumables, parts or spares
thereof shall not be treated as household waste and may
not be dropped in garbage bins. Product owners are
advised to deposit their product at the nearest collection
point for the recycling of electrical and electronic
equipment. Your co-operation shall facilitate proper
disposal & help prevent potential negative
consequences/hazards to the environment and human
health, which could otherwise be caused by
inappropriate waste disposal including improper
handling, accidental breakage, damage and/ or improper
recycling of e-waste. The recycling of materials will help
to conserve natural resources. For more detailed
information about recycling of this product, you may
contact our company’s toll free number and website in
India for assistance.
Toll Free: 1800-103-7799
Visit: www.sony.co.in for product recycling
Reduction in the Use of Hazardous Substances in
Electrical & Electronic Equipment (Applicable in
Republic of India)
This product and its components, consumables, parts or
spares comply with the hazardous substances restriction
of India’s E-Waste (Management) Rules. The maximum
allowable concentrations of the restricted substances are
0.1% by weight in homogenous materials for Lead,
Mercury, Hexavalent Chromium, Polybrominated
Biphenyls (PBB) and Polybrominated Diphenyl Ethers
(PBDE), and 0.01% by weight in homogenous materials
for Cadmium, except for the exemptions specified in
Schedule II of the aforesaid Rules.
For kundene i Norge
Dette utstyret kan kobles til et IT-
strømfordelingssystem.
Apparatet må tilkoples jordet stikkontakt
Suomessa asuville asiakkaille
Laite on liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan
För kunderna i Sverige
Apparaten skall anslutas till jordat uttag
For kunder i Danmark
Apparatets stikprop skal tilsluttes en stikkontakt med
jord, som giver forbindelse til stikproppens jord.
Türkiye’deki müşteriler için
AEEE Yönetmeliğine Uygundur
For the customers in the U.S.A.
SONY LIMITED WARRANTY - Please visit http://
www.sony.com/psa/warranty for important
information and complete terms and conditions of
Sony’s limited warranty applicable to this product.
For the customers in Canada
SONY LIMITED WARRANTY - Please visit http://
www.sonybiz.ca/pro/lang/en/ca/article/resources-
warranty for important information and complete
terms and conditions of Sony’s limited warranty
applicable to this product.
For the customers in Europe
Sony Professional Solutions Europe - Standard
Warranty and Exceptions on Standard Warranty.
Please visit https://pro.sony/en_GB/support-
services/warranty/support-professional-solutions-
europe-standard-product-warranty for important
information and complete terms and conditions.
For the customers in Korea
SONY LIMITED WARRANTY - Please visit http://
bpeng.sony.co.kr/handler/BPAS-Start for important
information and complete terms and conditions of
Sony’s limited warranty applicable to this product.
Table of Contents 5
Table of Contents
Precaution ....................................................... 6
On Safety ...................................................................6
On Installation .........................................................6
Transportation of the Unit ......................................6
Connecting to Other Devices ................................6
Handling the Screen ................................................6
On High Brightness Display ...................................6
On Burn-in ...............................................................7
On a Long Period of Use .........................................7
On the Surface of the Unit ......................................7
On Long Periods of Continuous Use ....................7
Handling and Maintenance of the Screen ............7
On Dew Condensation ...........................................8
Notes on Security .....................................................8
On Repacking ...........................................................8
Disposal of the Unit .................................................8
On the Software Updates ........................................8
On Fan Error ............................................................8
Location and Function of Parts and
Controls .......................................................... 9
Front Panel................................................................ 9
Input Signals and Adjustable/Setting Items ....... 11
Rear Panel............................................................... 13
Preventing Falling of the Monitor
(BVM-E251) .................................................. 15
Mounting the Unit in a Rack
(BVM-E171) .................................................. 16
Attaching the Handle (BVM-E171) ............. 16
Connecting the Controller (BKM-17R) ....... 17
Connecting Multiple Units with the LAN ... 18
Connecting the HDMI cable ........................ 19
Connecting the Power Cord ......................... 19
To connect the AC power cord ............................19
Turning on the Monitor ........................................20
Initial settings ............................................... 20
Setting for the LAN to Connect Multiple
Units .............................................................. 22
Selecting the Monitor (Designation of the
Monitor or Group ID Number) ................... 23
Using the Menu ............................................ 25
Menu Operation Buttons...................................... 25
Setting and Adjusting Using the Menu ...............25
Entering the Channel Number ............................28
Aborting Menu Operation ....................................28
Protection of the Setting Values .................. 29
Protecting the setting values using the [Key
Protect] .................................................................29
Protecting the setting values using
[Password] ............................................................29
Adjustment Using the Menus ...................... 29
Items ........................................................................ 29
[Adjustment] Menu .............................................. 32
[Channel Configuration] Menu .......................... 36
[Auxiliary Setting] Menu ..................................... 46
[Function Setting] Menu ...................................... 47
[System Configuration] Menu ............................ 61
[File Management] Menu .................................... 67
[System Status] Menu ........................................... 69
[Controller] Menu ................................................. 71
[Key Protect] Menu ............................................... 74
Displaying the Monitor Status Page ............ 75
Upgrading the Monitor and Controller ....... 77
Saving the Upgrade Data in a USB memory
stick, etc. ............................................................... 77
Upgrading the Monitor ........................................ 78
Upgrading the Controller .................................... 79
Extending the Monitor Function with the
Optional License (BVM-E171 only) ............. 80
Purchasing the License Purchase Key ................ 80
Obtaining the Install Key File .............................. 81
Activating the Optional License for HDR-
compatibility ........................................................ 83
Connecting the SDI Signals ......................... 84
Troubleshooting ........................................... 85
Specifications ................................................ 86
BVM-E251 ............................................................. 86
BVM-E171 ............................................................. 87
Available Signal Formats...................................... 89
Aperture Modification Frequency ...................... 94
Picture Display Size .............................................. 95
Picture Frame Display .......................................... 97
Scan Mode Image ................................................ 100
Inserting/Ejecting the USB memory stick ....... 101
Dimensions ................................................. 103
BVM-E251 ........................................................... 103
BVM-E171 ........................................................... 105
BVM-E251/E171 ................................................. 106
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing Administrator, Inc. in the United States and
other countries.
Precaution
6
Precaution
On Safety
Operate the unit only with a power source as specified
in the “Specifications” section.
A nameplate indicating operating voltage, etc., is
located on the rear panel.
Should any solid object or liquid fall into the cabinet,
unplug the unit and have it checked by qualified
personnel before operating it any further.
Do not drop or place heavy objects on the power cord.
If the power cord is damaged, turn off the power
immediately. It is dangerous to use the unit with a
damaged power cord.
Unplug the unit from the wall outlet if it is not to be
used for several days or more.
Disconnect the power cord from the AC outlet by
grasping the plug, not by pulling the cord.
The socket-outlet shall be installed near the
equipment and shall be easily accessible.
On Installation
Allow adequate air circulation to prevent internal heat
build-up.
Do not place the unit on surfaces (rugs, blankets, etc.)
or near materials (curtains, draperies) that may block
the ventilation holes.
Do not install the unit in a location near heat sources
such as radiators or air ducts, or in a place subject to
direct sunlight, excessive dust, mechanical vibration or
shock.
BVM-E251
When installing the installation space must be secured
in consideration of the ventilation and service operation.
Do not block the ventilation slots, and vents of the
fans.
Leave a space around the unit for ventilation.
Leave more than 40 cm of space in the rear of the unit
to secure the operation area.
When the unit is installed on the desk or the like, leave at
least 1U (4.4 cm) of space above and below the unit.
Leaving more than 40 cm of space above the unit is
recommended in consideration of service operation.
BVM-E171
When the unit is installed in a rack, leave at least 1U (4.4
cm) of space above and below, 1.0 cm of space left and
right between the rack and the unit.
Transportation of the Unit
Do not subject the unit to severe vibration or high
impact conditions during transportation. Doing so may
result in deformation of the internal structure or exterior
of the unit, damage of the screen, malfunction of the
internal parts, or other damage.
Make sure not to expose the unit to strong vibration or
high impact when you transport the unit as cargo by
truck, ship, or air, or as luggage with a rolling luggage
bag.
Avoid transporting or carrying the unit with the display
facing up or down.
Also, pack the unit in the protective bag provided to
prevent dust from entering the unit.
Connecting to Other Devices
When connecting this unit to other devices, turn off this
unit and the other devices beforehand. Connecting
while turned on may cause a malfunction to this unit
and the other devices.
Handling the Screen
The OLED panel fitted to this unit is manufactured
with high precision technology, giving a functioning
pixel ratio of at least 99.99%. Thus a very small
proportion of pixels may be “stuck”, either always off
(black), always on (red, green, or blue), or flashing. In
addition, over a long period of use, because of the
physical characteristics of the organic light-emitting
diode, such “stuck” pixels may appear spontaneously.
These problems are not a malfunction.
Do not leave the screen facing the sun as it can damage
the screen. Take care when you place the unit by a
window.
Do not push or scratch the monitor’s screen. Do not
place a heavy object on the monitor’s screen. This may
cause the screen to lose uniformity.
The screen and the cabinet become warm during
operation. This is not a malfunction.
On High Brightness Display
Using the unit with the high brightness display for
extended periods may cause eyestrain or reduction of
eyesight. Be sure to take an occasional break when
using.
Follow RECOMMENDATION ITU-R BT.1702
“Guidance for the reduction of photosensitive
epileptic seizures caused by television” or other
guidelines when using.
Precaution 7
In the HDR display, the display surface may emit heat
when high brightness images are output. Do not touch
the surface.
When [2.4(HDR)], [S-LOG3(HDR)], [S-
LOG2(HDR)], [SMPTE ST2084(HDR)], [ITU-R
BT.2100(HLG)], or [S-LOG3(Live HDR)] is selected
for [Gamma] in the [Matrix/Color Profile] menu,
images are displayed in HDR (High Dynamic Range).
In this manual, this status is described as “HDR
display.”
For details on the HDR (High Dynamic Range) display, see
page 44.
On Burn-in
Due to the characteristics of the material used in the
OLED panel, permanent burn-in or reduction in
brightness may occur.
These problems are not a malfunction.
Images that may cause burn-in
Still images in the HDR display
Masked images with aspect ratios other than 16:9
Color bars or images that remain static for a long time
Character or message displays that indicate settings or
the operating state
On-screen displays such as center markers or area
markers
Images with a frame (including Multi-View displays)
For details on the HDR (High Dynamic Range) display, see
page 44.
To reduce the risk of burn-in
Turn off the character and marker displays
Press the MENU button to turn off the character
displays. To turn off the character or marker displays
of the connected equipment, operate the connected
equipment accordingly. For details, refer to the
operation manual of the connected equipment.
Do not display static images that contain high
brightness display, time codes, markers, or logos for
extended periods. Consider applying a display method
with low level signals of 100% or less.
Do not display the images with a frame for a long time.
Also, consider removing the frame during the Multi-
View display, or displaying the signal level of the frame
area by about 50% of the display area.
Reduce the brightness
Reduce the brightness as much as possible or reduce
the input signal level when you do not use the display.
Turn off the power when not in use
Turn off the power if the monitor is not to be used for
a prolonged period of time.
Screen saver
This product has a built-in screen saver function to
reduce burn-in. When an almost still image is displayed
for more than 10 minutes, the screen saver starts
automatically and the brightness of the screen decreases.
On a Long Period of Use
Due to an OLED’s panel structure and characteristics of
materials in its design, displaying static images for
extended periods, or using the unit repeatedly in a high
temperature/high humidity environments may cause
image smearing, burn-in, areas of which brightness is
permanently changed, lines, or a decrease in overall
brightness.
In particular, continually displaying an image smaller
than the monitor screen, such as displaying an image in
a different aspect ratio or displaying an image with a
frame, may expedite the above issues.
Avoid displaying a still image for an extended period, or
using the unit repeatedly in a high temperature/high
humidity environment such an airtight room, or around
the outlet of an air conditioner.
To prevent any of the above issues, we recommend
reducing brightness slightly, and to turn off the power
whenever the unit is not in use.
On the Surface of the Unit
The surface of the unit becomes extremely hot. Do not
touch the surface with your hand or body during power
distribution. It may cause a burn.
On Long Periods of Continuous Use
Using this unit for extended periods may cause eyestrain
or reduction of eyesight.
As soon as you feel physical discomfort or pain, stop
using this unit immediately and take a break.
If the physical discomfort or pain remains even after
taking a break, consult a physician.
Handling and Maintenance of the
Screen
The surface of the screen is specially coated to reduce
image reflection. Make sure to observe the following
points as improper maintenance procedures may impair
the screen’s performance. In addition, the screen is
vulnerable to damage. Do not scratch or knock against it
using a hard object.
Precaution
8
Be sure to disconnect the AC power cord from the AC
outlet before performing maintenance.
The surface of the screen is specially coated. Do not
attach adhesive objects, such as stickers, on it.
The surface of the screen is specially coated. Do not
touch the screen directly.
Wipe the screen surface gently with the supplied
cleaning cloth or a soft dry cloth to remove dirt.
Stubborn stains may be removed with the supplied
cleaning cloth, or a soft cloth slightly dampened with a
mild detergent solution.
The screen may become scratched if the cleaning cloth
is dusty.
Never use strong solvents such as alcohol, benzene,
thinner, acidic or alkaline detergent, detergent with
abrasives, or chemical wipe as these may damage the
screen.
Use a blower to remove dust from the screen surface.
On Dew Condensation
If the unit is suddenly taken from a cold to a warm
location, or if ambient temperature suddenly rises,
moisture may form on the outer surface of the unit and/
or inside of the unit. This is known as condensation. If
condensation occurs, turn off the unit and wait until the
condensation clears before operating the unit. Operating
the unit while condensation is present may damage the
unit.
Notes on Security
SONY WILL NOT BE LIABLE FOR DAMAGES OF
ANY KIND RESULTING FROM A FAILURE TO
IMPLEMENT PROPER SECURITY MEASURES ON
TRANSMISSION DEVICES, UNAVOIDABLE DATA
LEAKS RESULTING FROM TRANSMISSION
SPECIFICATIONS, OR SECURITY PROBLEMS OF
ANY KIND.
Depending on the operating environment,
unauthorized third parties on the network may be able
to access the unit. When connecting the unit to the
network, be sure to confirm that the network is
protected securely.
This product is used with a leased line or intranet
connection. Do not connect to an external network, as
security issues may occur.
On Repacking
Do not throw away the carton and packing materials.
They make an ideal container which to transport the
unit.
Disposal of the Unit
Do not dispose of the unit with general waste.
Do not include the monitor with household waste.
When you dispose of the monitor, you must obey the
law in the relative area or country.
On the Software Updates
This manual contains descriptions of functions
supported by software version 1.2 (or later).
Therefore, if you use software version 1.2 (or later)
updated from version 1.1 (or earlier), the following
function is different from what is described in this
manual.
The Auto Power Down function cannot be used.
On Fan Error
The fan for cooling the unit is built in. When the fan
stops and the OPERATE indicator flashes in red, the
OVER RANGE indicator flashes in amber, and the
STATUS indicator lights in magenta on the front panel
for fan error indication, turn off the power and contact
an authorized Sony dealer.
About this manual
The instructions in this manual are for the following
two models:
BVM-E251
BVM-E171
The illustration of BVM-E251 is used for the
explanations. Any differences in specifications are
clearly indicated in the text.
The controller for operating this unit used for the
explanation is the BKM-17R. When you use the BKM-
16R, refer to the operating instructions of BKM-16R.
Location and Function of Parts and Controls 9
Location and Function of Parts and Controls
Front Panel
Tally lamp
With factory settings, the tally lamp lights when pins No.
5 and No. 8 of the PARALLEL REMOTE connector on
the rear panel are shorted. By changing the setting in the
[Parallel Remote] menu (page 62) of the [System
Configuration] menu, different pins on the PARALLEL
REMOTE connector can be used to control the tally
lamp.
OPERATE indicator
When the power switch (on the rear panel) is turned on,
internal data initialization starts and the OPERATE
indicator flashes in red for a while. When the signal is
output, the indicator flashes in green to indicate that
data initialization continues. When initialization is
finished and the monitor enters its operation mode, the
indicator lights in green.
The OPERATE indicator is lit in red when the monitor
is in sleep mode (The STATUS indicator also lights in
magenta).
The monitor will be in sleep mode under the following
conditions:
[Sleep Mode] is set to [On] in the [Power] menu
(page 63) of the [System Configuration] menu and the
power switch (on the rear panel) is turned on. (The
OPERATE indicator will flash for initialization after
the switch is turned on, then will light.)
The monitor is changed from operation mode to
sleep mode by the controller.
Lights in green when the monitor is put into operation
mode from sleep mode by pressing the MONITOR
switch of the controller.
Notes
When the OPERATE indicator is flashing in red, the
monitor cannot be put into operation mode. Wait until
the indicator is steadily lit.
When the OPERATE indicator is flashing in green, the
monitor is not in full operation mode and images
cannot be displayed correctly. Wait until the indicator
is steadily lit in green.
The OPERATE indicator may indicate an error or
warning. For details, see “About error/warning signals of
the indicator” (page 10).
OVER RANGE indicator
Lights in amber when ABL (Automatic Brightness
Limiter) starts, and [ABL] is displayed at the bottom left
of the screen. For details, see [ABL Notification]
(page 66). Also, lights in amber when the signal level
exceeds the dynamic range of the signal processing
circuit in the following circumstances.
– when the monitor is not in the HDR display
– when an item other than [S-LOG2(SDR)] or [S-
LOG3(SDR)] is selected
Decrease the contrast or brightness when the OVER
RANGE indicator is lit.
Location and Function of Parts and Controls
10
The OVER RANGE indicator may indicate an error or
warning. For details, see “About error/warning signals of
the indicator” (page 10).
STATUS indicator
Slowly flashes in yellow when the screen saver is
activated, and quickly flashes in yellow when a warning
during startup occurs.
Lights in blue in the HDR display. Slowly flashes in blue
when the screen saver is activated in the HDR display,
and quickly flashes in blue when a warning during
startup occurs.
Also, the STATUS indicator is lit in magenta when the
monitor is in sleep mode (The OPERATE indicator also
lights in red).
The STATUS indicator may indicate an error or warning.
For details, see “About error/warning signals of the
indicator” (page 10).
About error/warning signals of the indicator
The OVER RANGE indicator, OPERATE indicator, and/
or STATUS indicator on the front panel may show an
error or warning while the monitor is being operated.
If the error or warning is shown, please contact your
Sony representative.
Error display
Warning display
–: Status except for error display.
1) For the indicator display when the [Over Range] function is enabled,
see page 66.
STATUS
indicator
OVER
RANGE
indicator
OPERATE
indicator
Symptom
Lights in
yellow
Lights in
amber
Flashes in
red
The power in the
panel part is
unusual.
Lights in
yellow
Flashes in
amber
Flashes in
red
The temperature in
the panel part is
unusual.
Flashes in
yellow
Lights in
amber
Flashes in
red
The ambient
temperature sensor
is unusual.
Flashes in
yellow
Flashes in
amber
Flashes in
red
Error at restarting.
Lights in
magenta
Flashes in
amber
Flashes in
red
Fan error.
Flashes in
magenta
Lights in
amber
Flashes in
red
Device error.
– – Lights in
amber
DC input voltage is
unusual.
Lights in
magenta
Lights in
amber
Flashes in
red
(quickly)
HDMI EDID error
STATUS
indicator
OVER
RANGE
indicator 1)
OPERATE
indicator
Symptom
– Flashes in
amber
– The luminance is
reduced to protect
the panel from an
increase of
temperature in the
panel part.
– Lights in
amber
– ABL activation or
over range
– – Flashes in
amber
DC input voltage is
decreased.
Location and Function of Parts and Controls 11
Input Signals and Adjustable/Setting Items
Item
Input signal
Analog SDI HDMI
Composite SD 3G/HD
YCbCr YCbCr RGB XYZ
CONTRAST      
BRIGHT      
CHROMA 15) × × 7)
PHASE 15)
(NTSC)
× × × × ×
Picture Auto Adjust × × × × ×
NTSC Setup Level
(NTSC)
× × × × ×
Position Adj 13) × × × × ×
Gamut Error Display ×   1) × 1)
Scan Mode 13)     
Native Scan
(×1, ×2) 2)
     
Native Scan
(Aspect Correction)
  ××× 6) 8)
16:9   3) 4) 4) 5) 8) 9)
H Delay × ×   
V Delay × ×   
Char Off      
Color Temp      
Status      
Aperture 10)      
Mono      
Blue Only      
R Off      
G Off      
B Off      
Chroma Up × × 7)
Interlace See “Picture Frame Display” on page 97.
Pixel Zoom      
Capture × × ×
Capture Load      
Marker      8)
Aspect Marker      8)
Area Marker 1      8)
Area Marker 2      8)
Center Marker      8)
Aspect Marker-Line      8)
Aspect Blanking-Half      8)
Aspect Blanking-Black      8)
Side by Side      
Wipe      
Butterfly      
Location and Function of Parts and Controls
12
: Adjustable/can be set
× : Not adjustable/cannot be set
1) Does not function when the RGB signal with the
quantization range set to Full is selected. It functions,
however, if [Gamma] is set to [S-LOG2(SDR)] or [S-
LOG3(SDR)] in the [Color Profile] menu.
2) Fixed to [×1] when the HD signal or the computer signal
of HDMI is input.
3) Fixed to [16:9] with 720P input signal.
4) Becomes [1.896:1] with 2048 × 1080 input signal.
5) Excludes 640 × 480/60*P. Fixed to [16:9] with 1280 × 720/
50P, 60*P. (* Also compatible with 1/1.001.)
6) In effect with SD format
7) Functions when the YCbCr signal is input.
8) Does not function when the computer signal of HDMI is
input.
9) Functions when the [HDMI Auto] menu (page 39) of the
[Screen Aspect] menu is set to [Off].
10) For the operable input signal, see “Aperture Modification
Frequency” (page 94).
11) Sets when the SDI signal is input
12) Enabled only when the signal system is 480/59.94i.
13) When the composite signal is input and [Under Scan] is
selected, the blanking area of the horizontal direction is
masked.
14) Enabled during HD-SDI only
15) Does not function when the software version is 1.1 or later,
and [Gamma] is set to [S-LOG3(SDR)], [S-LOG2(SDR)],
[S-LOG3(HDR)], [S-LOG2(HDR)], [SMPTE
ST2084(HDR)], [ITU-R BT.2100(HLG)], or [S-
LOG3(Live HDR)].
16) Cannot be selected in the HDR display. [On] is always set
for signals of vertical frequency 24 Hz, 25 Hz, 48 Hz, and
50 Hz. [Off] is always set for signals of 30 Hz and 60 Hz.
Blending      
Error Notify Clear ×   1) × 1)
Audio Level Meter 11) × ×   
ALM Hold Reset 11) × ×   
Time Code × ×   
Flicker Free 16)      
Closed Caption × 12) 14) ×××
Item
Input signal
Analog SDI HDMI
Composite SD 3G/HD
YCbCr YCbCr RGB XYZ
Location and Function of Parts and Controls 13
Rear Panel
SDI input and output connectors (BNC)
SDI 1 IN connector
Input connector for serial digital signals.
SDI 2 IN connector
Input connector for serial digital signals.
MONITOR OUT connector
MONITOR OUT for SDI 1 IN and SDI 2 IN
connectors.
Notes
MONITOR OUT is activated when the unit is
turned on or in sleep mode.
MONITOR OUT cannot be used when powered
down by the Auto Power Down function or when
the main power is off.
COMPOSITE input and output connectors
(BNC)
IN connector
Input connector for composite video signals.
OUT connector
Loop-through output connector.
Notes
When the composite signal is used, adjust the signal
level in the [Picture Adj] menu (page 32).
When inputting a video signal with the jitters, etc.
the picture may be disturbed. We recommend using
the TBC (time base corrector).
When the unit is turned off, the signal wave of the
COMPOSITE input and output connectors may be
distorted.
BVM-E251
BVM-E171
Location and Function of Parts and Controls
14
HDMI IN (HDMI input) connector
Input connector for HDMI 1) signals.
HDMI (High-Definition Multimedia Interface) is an
interface that supports both video and audio on a single
digital connection, allowing you to enjoy high quality
digital picture and sound. The HDMI specification
supports HDCP (High-bandwidth Digital Content
Protection), a copy protection technology that
incorporates coding technology for digital video signals.
1) The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing Administrator,
Inc. in the United States and other countries.
Note
The HDMI audio signal is not available for this monitor.
Use HDMI compliant cable (sold separately), Category 2
(High Speed HDMI Cable), with HDMI logo.
DC 12V OUT connector (female)
Supplies the DC power to the controller.
Connect to the DC 12V connector of the controller with
the SMF-17R20 or the cable supplied with the BKM-
37H/38H/39H.
PARALLEL REMOTE connector (RJ-45, 8-pin)
Forms a parallel switch and controls the monitor
externally.
CAUTION
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
Pin assignment
You can assign functions using the [Parallel Remote]
menu (page 62) of the [System Configuration] menu.
Wiring required to use the Remote Control
Connect the function you want to use with a Remote
Control to the Ground (Pin 5).
LAN (10/100) connector
Connect to the LAN (10/100) connector of the
controller by using the SMF-17R20 or the cable supplied
with the BKM-37H/38H/39H. Or connect to the
network or the LAN (10/100) connector of the controller
by using a 10BASE-T/100BASE-TX LAN cable
(shielded-type, sold separately).
CAUTION
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
When you connect the LAN cable of the unit to
peripheral device, use a shielded-type cable to prevent
malfunction due to radiation noise.
The connection speed may be affected by the network
system. This unit does not guarantee the
communication speed or quality of 10BASE-T/
100BASE-TX.
NETWORK switch
LAN: When connecting to the network.
PEER TO PEER: When connecting to the LAN (10/100)
connector of the controller in 1 to 1 connection.
DC IN 24V – 28V (DC power input) connector
(XLR 4-pin, male)
Connect the 24V to 28V DC power supply.
AC IN connector (3-pin)
Connects the monitor to an AC power source, via the
supplied AC power cord.
Power switch
When turned on, the monitor enters operation mode. By
setting in the [Power] menu (page 63) of the [System
Pin number Functions
1 Designating input signal channel 1
(numeric keypad function)
2 Designating input signal channel 2
(numeric keypad function)
3 Marker (set in the [Marker Setting]
menu) On/Off (MARKER button
function)
4 Selecting whether monochrome image
is displayed or the monitor switches the
display mode automatically between
color image and monochrome image
depending on the input signal (MONO
button function).
5 GND
6 Not connected
7 Not connected
8 Tally lamp On/Off
Pin number Functions
1 – (GND)
2 NC
3 NC
4 + (DC 24V – 28V)
Pin number Functions
Preventing Falling of the Monitor (BVM-E251) 15
Configuration] menu, the monitor can also be set to
enter sleep mode when the power switch is turned on.
Note
If a no input-signal state continues for 60 minutes, the
monitor is powered down automatically by the Auto
Power Down function. To turn on the monitor, cut off
the power supply or turn off the power switch, then turn
the power back on. To change the settings, see [Auto
Power Down] (page 63) of [Power] in the [System
Configuration] menu.
Preventing Falling of the
Monitor (BVM-E251)
1
Tie a piece of stout string (commercially available)
to the left and right handles of the monitor.
2
Secure the ends of the string to the floor or wall.
String
String
String
16 Mounting the Unit in a Rack (BVM-E171) / Attaching the Handle (BVM-E171)
Mounting the Unit in a
Rack (BVM-E171)
To mount the unit in an EIA standard 19-inch rack, use
the supplied rack mount brackets and screws.
1
Remove the four feet from the bottom of the unit.
2
Attach the rack mount brackets to each side of the
unit with the supplied screws.
3
Screw the rack mount brackets to the rack to mount
the unit.
Use the commercially available screws that match
the size of the rack’s holes.
Attaching the Handle
(BVM-E171)
1
Remove the 2 screws on the top side.
Note
Keep the removed screws in a safe place to prevent
them from being lost.
2
Attach the handle with the supplied screws.
Notes
Make sure that the screw clamp is not loosened.
Secure the handle attachment.
Rack mount
bracket
Screws (supplied)
Rack
Screws (supplied)
Handle
(supplied)
Connecting the Controller (BKM-17R) 17
Connecting the Controller
(BKM-17R)
Note
When you connect the BKM-16R, refer to the operating
instructions of BKM-16R.
1
Turn off the power switch of the monitor before
connecting the units.
2
Set the NETWORK switches of the monitor and the
controller to PEER TO PEER.
3
Connect the LAN (10/100) connector of the
monitor and the LAN (10/100) connector of the
controller by using the SMF-17R20 or the cable
supplied with the BKM-37H/38H/39H, or a
10BASE-T/100BASE-TX straight LAN cable
(shielded-type, sold separately).
4
Connect the DC 12V OUT connector of the
monitor and DC 12V connector of the controller by
using the SMF-17R20 or the cable supplied with the
BKM-37H/38H/39H. Or connect the output cable
of the AC adaptor supplied with the controller to
the DC 12V connector of the controller.
Note on connecting the cable to the DC 12V
OUT connector
Insert the connector so as to fit the shape of the DC 12V
OUT connector.
NETWORK switch:
Set to PEER TO PEER.
LAN (10/100)
connector
DC 12V OUT
connector
LAN (10/100)
connector
DC 12V connector
SMF-17R20, etc.
Controller
(BKM-17R)
NETWORK switch:
Set to PEER TO PEER.
Connecting Multiple Units with the LAN
18
Connecting Multiple Units
with the LAN
The controller controls up to 32 monitors. Up to three
controllers are connected to one monitor in single mode.
Notes
The controller cannot control monitors in another
subnetwork.
When you connect the BKM-16R, refer to the
operating instructions of BKM-16R.
1
Turn off the power switch of the monitor before
connecting the units.
2
Connect to the network by using a 10BASE-T/
100BASE-TX cable (shielded-type, sold separately).
Note
We recommend to use an optional switching hub
with auto selection function (AUTO MDI/MDI-X)
of a straight/cross cable.
3
Connect the output cable on the AC adaptor
supplied with the controller to the DC 12V
connector of the controller.
Note
When multiple units are connected, set for the LAN
before setting the NETWORK switch to LAN
(page 22).
4
Set the NETWORK switches of each monitor and
the controller to LAN.
NETWORK switch:
Set to LAN.
NETWORK switch:
Set to LAN.
LAN (10/100)
connector
LAN (10/100)
connector
Switching hub
(recommended:
with AUTO MDI/
MDI-X function)
AC adaptor
(supplied with the
BKM-17R)
LAN (10/100)
connector
DC 12V
connector
Controller
(BKM-17R)
NETWORK switch:
Set to LAN.
19
Connecting the HDMI cable / Connecting the Power Cord
Connecting the HDMI
cable
1
Remove the two screws on both sides of the HDMI
IN connector.
2
Attach the HDMI cable holder (supplied) with the
removed screws.
3
Insert the HDMI cable and fix with a commercially-
available cable fixer (1 piece).
Connecting the Power
Cord
You can operate the monitor with AC or DC power
supply.
To connect the AC power cord
1
Plug the AC power cord into the AC IN connector
on the rear panel then attach the AC plug holder
(supplied) to the AC power cord.
2
Slide the AC plug holder over the cord until it locks.
To remove the AC power cord
Pull out the AC plug holder while pressing the lock
levers.
To connect the DC power supply
Connect the DC power supply to the DC IN 24V - 28V
connector.
When the AC power cord and DC power supply are
connected, the AC power supply is given preference over
the DC power supply. To use the DC power supply,
disconnect the AC power cord.
HDMI cable holder (supplied)
Cable fixer
HDMI cable
AC IN connector
AC power cord (supplied)
AC plug holder
(supplied)
Initial settings
20
Turning on the Monitor
Press the power switch on the rear panel to turn on the
power.
When you turn on the monitor for the first time after
purchasing it, the [Select Area] screen is displayed. Select
the area where you intend to use this monitor.
For selecting the area, see page 20.
The warm-up time is more than 30 minutes,
approximately.
When the monitor is in sleep mode
When the monitor is in sleep mode, the OPERATE
indicator is lit in red and the STATUS indicator is lit in
magenta. Press the MONITOR switch of the
controller to turn on the monitor.
The OPERATE indicator lights in green and the monitor
enters operation mode.
Initial settings
When you turn on the monitor for the first time after
purchasing it, select the area where you intend to use this
monitor from among the options.
When the area is selected, the menu item settings
suitable for the selected area are applied.
Default value for each area
Note on the setting of color temperature
If you measure the color temperatures of different
display types, such as CRT, LCD, or OLED, by using a
common (or general) color analyzer that is based on CIE
1931, and adjust the xy chromaticity to the same value,
the appearance may be different because of optical
spectrum differences.
To compensate for this difference, the [D93], [D65],
[D61], [D55], and [User1] to [User5] settings (except
[DCI]) of the monitor are adjusted by an offset 1).
1) The offset value applied (x-0.006, y-0.011) is based on the
Judd’s function to the CIE 1931 (x, y) value.
[Color
Temp]
[Setup
Level] [Color Profile]
[North America] [D65] [7.5%] [ITU-R BT.709]
[Latin America]
[PAL & PAL-N Area]
Argentina [D65] [0%] [ITU-R BT.709]
Paraguay [D65] [0%] [ITU-R BT.709]
Uruguay [D65] [0%] [ITU-R BT.709]
[NTSC & PAL-M Area] Other Area [D65] [7.5%] [ITU-R BT.709]
[Africa]
[Australasia]
[Europe]
[Middle-East]
[D65] [0%] [ITU-R BT.709]
[Asia Except Japan]
[NTSC Area] [D65] [7.5%] [ITU-R BT.709]
[PAL Area] [D65] [0%] [ITU-R BT.709]
[Japan] [D93] [0%] [ITU-R BT.709]

Termékspecifikációk

Márka: Sony
Kategória: hangszóró
Modell: Trimaster BVM-E251

Szüksége van segítségre?

Ha segítségre van szüksége Sony Trimaster BVM-E251, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hangszóró Sony

Sony

Sony SS-MB200H Útmutató

23 December 2024
Sony

Sony SS-SPG01 Útmutató

23 December 2024
Sony

Sony SS-RX900 Útmutató

7 Október 2024
Sony

Sony SS-AC5 Útmutató

21 Szeptember 2024
Sony

Sony SS-X9S Útmutató

19 Szeptember 2024
Sony

Sony CFD-G555CPK Útmutató

9 Szeptember 2024
Sony

Sony ULT FIELD 1 Útmutató

1 Szeptember 2024
Sony

Sony ULT FIELD 7 Útmutató

1 Szeptember 2024
Sony

Sony LMD-B240 Útmutató

1 Szeptember 2024
Sony

Sony SCA-S30 Útmutató

24 Augusztus 2024

Útmutatók hangszóró

Legújabb útmutatók hangszóró

Behringer

Behringer B2520 PRO Útmutató

10 Április 2025
Marshall

Marshall Willen Útmutató

10 Április 2025
JBL

JBL Control 426LP Útmutató

9 Április 2025
Crestron

Crestron SAROS IC8T Útmutató

8 Április 2025
LD Systems

LD Systems STINGER G3 TMB Útmutató

8 Április 2025
JBL

JBL Conceal C83 Útmutató

8 Április 2025
Crestron

Crestron SAROS ICE4T Útmutató

7 Április 2025
Crestron

Crestron SAROS ICI6T Útmutató

7 Április 2025
Focal

Focal K2 Power M FRAK Útmutató

5 Április 2025
Match

Match UP C42BMW-FRT.3 Útmutató

3 Április 2025