Használati útmutató Smith Corona MEMORY CORRECT

Smith Corona MEMORY CORRECT

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Smith Corona MEMORY CORRECT (2 oldal) a kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
Margins
Margins are preset depending on your pitch
setting. They are:
10 Pitch 12 Pitch 15 Pitch
(Pica) (Elite) (Micro)
Left Margin 12 14 18
Right Margin 72 86 108
Changing Margins
When you need to change the margins,
follow the instructions below:
1. Press Back Space or Spacebar to
desired left margin.
2. Press Margin. Unit beeps.
3. Press Spacebar to desired right margin.
4. Press Code + Margin. Unit beeps.
Note: To signal that you are near the right
margin, your typewriter will beep once 5
spaces before the right margin.
Tabs
You can set up to six tabs, either regular or
decimal. Tabs may be set outside of
margins.
Regular Tab Decimal Tab
This is 123.56
a Regular 12.47
Tab 2.09
Regular Tabs
Regular tabs justify text at the tab stop. To
set a regular tab:
1. Position print hammer at desired location.
2. Press Tab S. Unit beeps.
Decimal Tabs
Decimal tabs are used to align numbers with
the decimal point. To set a decimal tab:
1. Position the print hammer at desired
location.
2. Press Code + D. Tab (O). Unit beeps.
3. Repeat steps 1 and 2 to set more decimal
tabs if desired.
4. Press Return when all tabs are set.
Using Tabs
Once tabs are set, they can be used as you
are typing your text.
1. Press Tab to move to tab location.
2. Type text. If using a decimal tab, type the
numbers preceding the decimal point. The
carrier moves to the left for each number
you type. If you make a mistake, press
Tab to start again.
3. Type the decimal point. The numbers
print to this point.
4. Type the numbers following the decimal
point.
Clearing a Tab
Both types of tabs are cleared the same way.
1. Position print hammer to tab setting.
2. Press Code + Tab (Tab C). Release
immediately. Unit beeps.
Clearing All Tabs Quickly
Press and hold Code + Tab (Tab C) until 2
beeps are heard. If you are positioned at a
tab stop, you will hear 3 beeps.
Pitch
Your typewriter has been designed with triple
pitch capabilities. To set the Pitch:
Press Code + Tab S for 10 Pitch.
Press Code + 1 for 12 Pitch.
Press Code + 2 for 15 Pitch.
Unit beeps when selecting pitch.
Note: Your typewriter is set at 10 pitch.
Change the printwheel if you select another
pitch. Changing pitch in the middle of a line
erases Correction Memory. However, after
the new pitch is selected, Correction Memory
begins again.
Line Spacing
Each time you turn the typewriter on, it is set
for single line spacing. You can change line
spacing to 1
1
⁄
2
line spacing or double line
spacing. To change line spacing:
Press Code + 3 for single line spacing.
Press Code + 4 for 1
1
⁄
2
line spacing.
Press Code + 5 for double line
spacing.
Unit beeps when selecting line spacing.
Impression Control
Impression control is the force used by the
print mechanism to strike the paper. When
you turn the typewriter on, it is set at
medium. You can change to light or heavy
impression. It is recommended that you
select heavy impression when typing on
carbons. For normal typing, use medium
impression. To set impression control:
Press Code + L for light impression.
Press Code + M for medium
impression.
Press Code + H for heavy impression.
The unit beeps when Impression control is
changed.
Note: Standard bond paper stock is
recommended for best quality. Copier paper,
erasable bonds and very heavily textured
bond papers do not print well with
Correctable Film ribbon. For these paper
types, we recommend High Density
Correctable Film or Multi-Strike ribbons. If
typing stencils, use those specifically
designed for daisywheel printers.
Correcting Text
There are two ways to correct typing errors:
off-line and on-line. The half-space feature
can be used for both.
On-Line Correction
The typewriter can automatically correct all
characters in a one-line memory buffer called
the Correction Memory. You can easily
correct characters no longer in Correction
Memory using Off-Line correction. After
correcting an error you can quickly return to
your previous typing position.
Important: Bold and auto underscore must
be activated before correcting characters
having these enhancements.
Correct Key
Use Correct for erasing character(s) in
Correction Memory.
1. Position the print hammer on the incorrect
character and then press Correct. Hold
down Correct to continue correcting, or
press Back Space and then Correct
again until all characters are removed.
2. Type correct text.
3. Press Code + Reloc (Return) if
necessary to relocate. The unit beeps.
Note: You erase Correction Memory when
you turn off the typewriter, press Return,
change pitch, or use the Half Space feature.
WordEraser Key
Use WordEraser for erasing word(s) in
Correction Memory.
1. Position the print hammer on any
character in the right most word to be
corrected, and then press WordEraser
once for each word to be erased. If you
press WordEraser while between words,
the word to the left of the space will be
deleted.
2. Type correct text.
3. Press Code + Reloc (Return) if
necessary to relocate. The unit beeps.
Off-Line Correction
To correct an error not in the current line
Correction Memory:
1. Press Code + Up (6), Down (7), or
Return to position the print hammer on
the line containing the incorrect character.
2. Press Back Space or Spacebar to move
to incorrect character.
3. Press Code + Correct. The unit beeps.
4. With correction cassette installed, retype
the incorrect character to remove it.
5. Type the correct character.
Important: Bold and auto underscore must
be activated before correcting characters
having these enhancements.
Half Space
The Half Space feature is used when making
corrections when you omit a character or
type one too many. When the Half Space
feature is activated, the typing position
moves a half space to the right. Regular
spacing returns when the Half Space feature
is deactivated.
Note: When you activate the Half Space
feature, the Correction Memory is erased.
The typewriter remembers the half spaced
characters until the Half Space feature is
deactivated. Then, the typewriter begins to
remember normal spaced characters again.
Adding a Character
1. Press Correct or WordEraser to
erase error.
2. Press Back Space to position the carrier
one space before the first character of the
erased word.
3. Press Code + Half Space (Spacebar).
Print hammer advances a half space.
4. Type correct word.
5. Press Code + Half Space (Spacebar).
12
5
Important: Save all packing materials. If you
ship or move the typewriter, it should be
repacked in the original carton. See
“Shipping Instructions.”
This diagram depicts only basic features. For
information on coded features, see specific
chapters or the Quick Reference Guide at the
end of these instructions. Product
appearance and/or specifications are subject
to change without notice.
My Most Popular Features
Correcting Cassette
Easy to change and snap into place.
Automatic Memory Correction
Instant correction.
WordEraser
Erases an entire word.
Auto Center
Quickly and accurately centers text.
Bold
Highlights text.
Decimal Tab
Automatically aligns numbers by decimal
points.
Self Demonstration...
Activate this Self Demonstration Program
and discover my most popular features.
This built-in Demo is easy to use. Follow the
instructions below.
1. Insert Paper.
2. Press and hold Code while pressing Z.
3. Release both.
Hardware Basics
Typewriter Diagram
Inserting Paper
Note: Your typewriter handles 12” wide
paper and a 9” typing line. Standard bond
paper stock is recommended for best quality.
Copier paper, erasable bonds and very
heavily textured bond papers do not print
well with Correctable Film ribbon. For these
paper types, we recommend High Density
Correctable Film or Multi-Strike ribbons. If
typing stencils, use those specifically
designed for daisywheel printers.
1. Insert paper securely in the slot behind
the platen (3) against the paper alignment
mark. (For 12” wide paper, center on the
platen area.)
2. Advance
paper by using
the platen
knob (6), Index
Up/Down
feature, or
Return key.
3. Push the
paper release
lever (4) back,
and straighten
the paper if
necessary.
Return lever to
original
position.
4. Make sure the
protective
cover is in its
original
position.
Platen Knob/Variable Line Spacer
Rotate the platen knob to position the paper
up or down at variable line positions.
Removing Paper
To remove paper, push the paper release
lever back and gently pull the paper out of
the machine.
Turning the Typewriter Off
When typing is completed, move the power
switch to Standby. We suggest you unplug
the typewriter if it will not be used for an
extended period of time.
Keyboard
Code Key
The Code key is used in combination with
other keys to activate features. Code key
combinations are activated by pressing and
holding the Code key while pressing the
second key.
Shift Key
Press Shift while typing an alpha key to type
upper case letters or to type the characters
located on the top of certain keys, such as $, %.
Lock Key and
Indicator Light
Press Lock to type continuously in upper
case characters and access the characters
located on top of certain keys. The shift lock
light will light when Lock is pressed. To
deactivate shift lock, press Lock or a Shift
key. The light goes out.
Important: When the shift lock light flashes,
the typewriter has received an incorrect
command. Press Code to stop the flashing
light.
Repeat Action
All keys will automatically repeat when held
down except the following
Keyboard II characters: ^ ‘ ~ .
Format
Each time you turn on your typewriter, a
preset format is activated. It is set for general
typing purposes. These settings remain
active until you change them.
Setting Up
Before you can use your typewriter, you must
remove the packing materials from the print
mechanism. This is essential to the proper
functioning of your typewriter. Do not turn
the unit on until you have prepared the
typewriter for use. Follow the steps listed
below using the typewriter diagram for
reference. The numbers on the diagram
correspond to those in the instructions.
1. Tilt the protective cover (1) toward you.
2. Release the rubber band (left side first)
from the tabs.
3. Remove the print hammer restraint card.
4. Remove the ribbon cassette. If the
typewriter ribbon is slack, advance it by
turning the gear wheel on the bottom of
the cassette in the direction indicated (see
illustration).
5. Place the cassette back on the carrier,
and return the protective cover to its
original position. You will hear it snap into
place.
Turning the Typewriter On
The electrical cord is stored on the back of the
unit. Remove the plug from the protection slot
and unwind the cord for use.
1. Plug the typewriter into a proper electrical
outlet. (Use the correct electrical current.)
2. The symbol indicates the unit is in
Standby mode. This means your keyboard
is inactive until you select ON (|). Move
the power switch (5) to ON (|). The carrier
(2) moves to the preset left margin.
Removing a Character
1. Press Correct or WordEraser to
erase error.
2. Press Code + Half Space (Spacebar).
Print hammer advances a half space.
3. Type the correct word.
4. Press Code + Half Space (Spacebar).
Note: Before activating the Half Space
feature on another line, you have to remove
the error using off-line correction procedures.
(See “Off-Line Correction.”)
Enhanced Text
You can enhance your text by using Bold,
Auto Center, Underscore, Superscript and
Subscript.
Bold Print
This feature is used for highlighting text. To
use Bold:
1. Press Code + Bold (B). Unit beeps.
2. Type text.
3. Press Code + Bold (B) to deactivate
bold.
Important: Bold and auto underscore must
be activated before correcting characters
having these enhancements.
Auto Underscore
You can automatically underscore just the
words or the words and spaces using the
Auto Underscore feature.
Activating Word Underscore
1. Press Code + Word (_/-). Unit beeps.
2. Type text.
3. Press Code + Word (_/-) to deactivate
Underscore.
Activating Underscore All
1. Press Code + All (+/=). Unit beeps.
2. Type text.
3. Press Code + All (+/=) to deactivate
Underscore.
Manual Underscore
You can manually go back and underscore
text.
1. Position print hammer under the first
character of the text to be underscored.
2. Press Shift + —.
Auto Center
This feature automatically centers text
between current margins. To use Auto Center:
1. Press Code + Center (0). Unit beeps.
The carrier moves to the center of the
margins.
2. Type the text. The carrier will backspace
in half space increments for each
character typed.
3. Press Return. Text prints and centers
automatically.
Note: If you make a mistake, press
Code + Center to restart centering. If you
decide not to center text, press Return prior
to entering text.
Superscript/Subscript
Your typewriter can easily create superscript
and subscript characters.
Typing Superscripts
1. Press Code + Super (9). Typing position
moves up
1
⁄
2
line.
2. Type the superscript. Carrier returns to
the original line.
Typing Subscripts
1. Press Code + Sub (8). Typing position
moves down
1
⁄
2
line.
2. Type the subscript. The carrier returns to
the original line.
Note: If you superscript or subscript more
than one character, you must repeat steps 1
and 2 above. If you decide not to type a
superscript or subscript after activating the
feature, press Correct to return to the
original line.
Correcting Superscript and
Subscript Errors
To correct errors made while using
Superscript or Subscript:
1. Press Back Space to error.
2. Activate superscript or subscript.
3. Press Code + Correct.
4. Type the incorrect character. It is erased
and carrier returns to original line.
This User’s Manual should be used with the following model: Memory Correct.
Copyright Smith Corona Corporation, 1997.
799558 Rev. A NAES Printed in USA
Code
Lock
Shift
R
`
RRRRRR
4
3
6
MEMORY CORRECT
Electronic Typewriter
Multi-Strike Film with Cover-Up
Correction
When using Multi-Strike film ribbon
cassettes, use Smith Corona Cover-Up
correcting cassettes.
Cover-Up tape covers your errors neatly and
quickly. Cover-Up correcting cassettes have
a pink cut-out on the lower right.
Removing the Ribbon Cassette
Replace the ribbon cassette when a different
colored portion begins to unwind from it.
1. Tilt protective cover forward.
2. Grasp cassette on both sides.
3. Lift cassette STRAIGHT up and out.
Inserting the Ribbon Cassette
1. Turn the gear wheel on the bottom of the
cassette in the direction indicated to
tightly wind the cassette.
2. Turn the cassette over with the name face
up and the ribbon toward the print hammer.
3. Set the cassette in the carrier while
guiding the ribbon between the printwheel
and the typing guide. Press down. Ribbon
snaps into place.
4. Return protective cover to its original
position. Be sure it snaps into place.
Note: Stencils designed specifically for
daisywheel typewriters perform best when the
print ribbon is inserted. To determine which
brand best fits your individual requirements,
check with your office supplies retailer.
Correcting Cassettes
Replace the correcting cassette when a
different colored portion unwinds from the
right spool.
Removing the Correcting Cassette
1. Tilt protective cover forward, and remove
the print ribbon cassette.
2. Grasp correcting cassette on sides as
shown. Lift correcting cassette up and out.
Inserting a New Correcting Cassette
1. Turn appropriate gear wheel on bottom of
the correcting cassette in direction
indicated by arrows to wind tightly.
2. Hold correcting cassette (using both
hands as shown) with the Smith Corona
name facing up.
3. Guide correcting tape between the
printwheel and typing guide and position
left gear wheel on left mount and right
gear wheel on right mount.
4. Snap correcting cassette securely in place.
Important: After the cassette is
mounted, tighten slack in tape by
moving red plastic lever toward platen.
The lever is located under left side of
cassette towards the platen. Repeat as
many times as necessary.
5. Replace ribbon cassette. Be sure
printwheel and print hammer are secure.
6. Return protective cover to its original
position. Be sure it is closed securely.
Printwheels
Removing the Printwheel
1. Move switch to Standby .
2. Tilt the protective cover forward.
3. Remove the print ribbon cassette and
correcting cassette.
4. Locate the print hammer release/engage
lever (left of print hammer). Press the lever
toward you until
the print hammer
mechanism springs
away from the
printwheel.
5. Lift the printwheel
up and out.
Inserting a Printwheel
1. Drop printwheel between print hammer
and typing guide with type style name
facing you.
2. Push the print hammer release lever back
to secure the printwheel.
3. Replace the correcting cassette and
ribbon cassette.
4. Return the protective cover to its original
position.
5. Return the switch to the operating
position.
Important: If incorrect characters are printed,
after changing the printwheel, turn the
typewriter off, then on.
Cleaning
Do not attempt to disassemble the typewriter
to clean it.
Important: Always unplug the machine
before using cleaning solutions on its
surfaces.
Printwheel
To remove residue, dip the characters into a
small container of ethyl or isopropyl alcohol
(rubbing alcohol) and wipe with a clean dry
cloth. Do not soak the printwheel.
Platen
Wipe surface with a clean cloth dampened
with ethyl or isopropyl alcohol (rubbing
alcohol).
Keyboard
To clean the keyboard, dampen a sponge
with a mild ammonia or soap solution. DO
NOT use household cleaners containing
chlorinated compounds. DO NOT spray
anything directly on the product.
Warning: Keep all solvents and petroleum
distillates (gasoline, kerosene, lighter fluids,
etc.) away from plastic parts. Keep all
cleaning solutions away from electrical
components and moving parts.
Check Points
If your typewriter does not function properly,
check the following:
✔Is the typewriter plugged into a live
socket?
✔Is the typewriter switched on?
✔Is the protective cover completely closed?
✔Are the printwheel, ribbon cassette and
the correcting cassette properly installed?
✔Have the ribbon or correcting cassette
been used up?
✔Is the carrier lock completely disengaged?
✔Are compatible ribbon and correcting
cassettes installed?
✔Is the print hammer in a locked position?
✔Has a foreign object fallen into the
typewriter?
If the typewriter still does not work properly
after checking the above, contact your
nearest Smith Corona Service Center.
Obtaining Service
If you are experiencing difficulty, before
returning the unit for service, call Consumer
Affairs, toll-free at 1-800-448-1018, for
assistance. Customer Service
Representatives are available to assist you
Monday through Friday, from 8:00 AM to
6:00 PM, EST.
Note: If you need to send your unit for
service, to qualify for Warranty, proof of
purchase must accompany the unit. Your
sales receipt is your proof of purchase.
Shipping Instructions
Important: When the machine is to be
shipped for any reason, the printwheel carrier
inside the typewriter must be stabilized to
prevent movement. The typewriter as a
whole must be properly protected from
shipping and handling hazards. Use original
packing material to pack the unit.
Stabilizing the Printwheel Carrier
1. Tilt the protective
cover forward.
2. Select a rubber
band to use to
secure the carrier
mechanism.
3. Place the rubber
band around the
foot retainer on
the right side of
the machine.
Position the
carrier
mechanism near
the rubber band.
• BEFORE CLEANING any part of your unit,
make sure it is unplugged.
• WHEN FINISHED TYPING, switch to
Standby or Off. Unplug unit if it is not to
be used for an extended period. Unplug
unit for a complete cut from the main
electrical circuit.
Warning: To reduce the risk of fire or
electric shock, do NOT expose unit to rain or
moisture.
Product Consumer Warranty
Limited Warranty
90 Day Warranty
Smith Corona warrants this typewriter
against defects in material or workmanship
for a period of 90 days from the date of
original purchase for use, and agrees to
repair or, at our option, replace any defective
unit without charge for either parts or labor.
Proof of Purchase will be required.
Limited Warranty
Following the first 90 days from the date of
purchase and thereafter until 1 year from the
date of purchase Smith Corona will replace
any defective part at no charge. There will be
a standard charge for labor and the cost of
transportation.
Important: This warranty does not cover
damage resulting from accident, misuse or
abuse, any modification or alteration
including attaching the unit to other than the
recommended receptacle or voltage, nor
does it cover ribbon replacement or cleaning
of the unit.
THIS WARRANTY IS VOID WHEN SERVICE
OR REPAIRS ARE PERFORMED BY A NON-
AUTHORIZED SERVICE LOCATION. This
warranty does not cover shipping expenses
to and from a service location.
NO RESPONSIBILITY IS ASSUMED FOR
ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES. You may
obtain warranty service through one of our
service locations. To obtain the location of
the nearest Service Center, call toll-free:
1-800-448-1018
The toll-free number operates Monday
through Friday, from 8:00 a.m. to 6:00 p.m.
Eastern Time. Simply take or ship the unit
prepaid to the nearest service location.
Damage occurring during transit is not
covered by this warranty.
Note: No other warranty, written or verbal, is
authorized by Smith Corona. This warranty
applies to units sold in the United States and
Puerto Rico only.
This warranty gives you specific legal rights,
and you may also have other rights which
vary from state to state. Some states do not
allow the exclusion or limitation of incidental
or consequential damages or limitations on
how long an implied warranty lasts, so the
above exclusion and limitations may not
apply to you.
Smith Corona Corporation
839 Route 13 South
P.O. Box 2090
Cortland, New York 13045-0980
Warning: Use Smith Corona “H” Series
supplies. Use of non-Smith Corona (brand or
manufactured) supplies or accessories will not
(except as noted below) void this warranty.
THE WARRANTY WILL BE VOID if the
typewriter is damaged or rendered wholly or
partially inoperable as a result of using a
non-Smith Corona supply or accessory
item(s).
FCC
The following information is provided to you
in accordance with the rules and regulations
of the United States Federal Communications
Commission. Questions concerning this
information can be directed to Smith Corona
Corporation by writing:
Smith Corona Corporation
839 Route 13 South
Box 2090
Cortland, NY 13045
Note: This typewriter generates and uses
radio-frequency energy and if not installed
and used properly, that is, in strict
accordance with the manufacturer’s
instructions, may cause interference to radio
and television reception. It has been type
tested and found to comply with the limits for
a Class B typewriter in accordance with the
specifications in Sub-part J of Part 15 of
FCC rules, which are designed to provide
reasonable protection against such
interference in a residential installation.
However, there is no guarantee that
interference will not occur in a particular
installation. If this typewriter does cause
interference to radio or television reception,
which can be determined by turning the
typewriter off and on, the user is encouraged
to try to correct the interference with one or
more of the following measures:
Quick Reference Guide
Function Command
Activates Caps Lock Lock
Auto Center Code + Center (0)
Auto Return Code + Back Space
Auto Underscore All Code +/=
Auto Underscore Word Code + _/-
Bold Print Code + B
Clears Tabs Code + Tab (Tab C)
Correct Characters Correct
(On-line)
Correct One Character Code + Correct
(Off-line)
Correct Words (On-line) WordEraser
Decimal Tab Code + O
Half Space Code + Spacebar
Heavy Impression Control Code + H
Index Up Code + 6
Index Down Code + 7
Keyboard II Code + Desired
Keyboard II character
Left Margin Margin
Light Impression Control Code + L
Manual Underscore Code + —
Medium Impression Code + M
Control
Move to Tab Setting Tab (Tab C)
Regular Tabs Tab S
Return to Previous Code + Return
Typing Position (Reloc)
Right Margin Code + Margin
Self-Demonstration Code + Z
Set Double Line Spacing Code + 5
Set 11⁄2 Line Spacing Code + 4
Set 10 Pitch (Pica) Code + Tab S
Set 12 Pitch (Elite) Code + 1
Set 15 Pitch (Micro) Code + 2
Set Single Line Spacing Code + 3
Subscript Code + 8
Superscript Code + 9
Keyboard II: International
Characters and Special Symbols
The Keyboard II feature allows you to access
the international characters and special
symbols (for example: ç é ¿ ) that appear on
the bottom right of certain keys.
Accessing Keyboard II Characters
Press Code then the desired Keyboard II
character key or symbol.
For those characters ( ^ ~ ‘ ) printed above
the letters, type the KB II character first. The
print hammer remains in place so you can
type a letter below the symbol.
Other Features
Your typewriter also has Index Up/Down and
Auto Return.
Index Up/Index Down
This feature moves the paper up or down in
increments equal to the current line space
setting.
To use Index Up/Down:
1. Press Code + Up (6) to move the typing
position up (paper down).
2. Press Code + Down (7) to move the
typing position down (paper up).
Note: These are repeating keys. If they are
held down, the paper will continue to move
up or down.
Auto Return
You can program your typewriter to
automatically return at the end of each line.
When a space or hyphen is typed in the
“warning zone,” which begins five spaces
before the right margin, the carrier
automatically returns to the next line. For
lengthy words falling at the end of the line,
simply type a hyphen as you normally would
and the carrier returns automatically. To
activate Auto Return:
1. Press Code + Return (Back Space).
Unit beeps.
2. Type text. Do not press Return at the
end of a line.
Deactivating Auto Return
Press Code + Return (Back Space).
Care and Maintenance
Ribbon Cassettes and
Correcting Cassette
Warning: Use Smith Corona brand “H”
Series supplies. Use of non-Smith Corona
(brand or manufactured) supplies or
accessories will not (except as noted below)
void this warranty.
THE WARRANTY WILL BE VOID IF the
typewriter is damaged or rendered wholly or
partially inoperable as a result of using a
non-Smith Corona supply or accessory
item(s).
Your Smith Corona typewriter uses Ribbon
and Correcting Cassettes with the Right
Ribbon System
®
feature. Smith Corona’s
patented Right Ribbon System feature
assures that the right combination of ribbon
and correcting cassette is inserted in the
typewriter.
• Assures use of Correctable film with Lift-
Off correction.
• Assures use of Multi-Strike film with
Cover-Up correction.
For example: Correctable film ribbon with
Cover-Up correcting cassette. If a
mismatched set is inserted, the ribbon
cassette cannot be fully or properly inserted
into your typewriter.
The exclusive Right Ribbon System feature
using the patented Smith Corona Ribbon and
Correcting Cassettes is designed to make
changing ribbons and correcting tapes quick,
easy, and error-free.
Because of Smith Corona’s patented
correcting tape feed mechanism, the lift-off
correcting cassette has approximately two
times the yield of spooled tapes found in
other machines.
Replace the ribbon cassette when a different
colored portion begins to unwind from the
Cassette. Be sure to use the Right Ribbon
System combination.
Correctable Film with Lift-Off
Correction
When using Correctable film ribbon
cassettes, use Smith Corona Lift-Off
correcting cassettes. Lift-Off tape removes
your errors quickly and cleanly. It will not
remove the print of a Multi-Strike ribbon.
Lift-Off correcting cassettes have a yellow
cut-out on the lower right.
4. Stretch the
rubber band
over the top of
the mechanism
and around the
tab on the left
side.
5. Return the
protective cover to its original position
and tape shut.
6. Wrap the cord around the cord wrap
panel as many times as possible. Some
excess cord will remain loose. Secure the
plug in the protection slot. Tuck the
excess cord up under the lip. Your
typewriter is ready for transport.
Note: If the original packing materials are not
available or the carrier cannot be put into the
correct position, ball up single sheets of
newspaper and insert them on each side of
the carrier until all open spaces are filled to
capacity.
Packing the Typewriter
Pack the typewriter in the original materials. If
you do not have the original packing
materials:
1. Use box slightly larger than the typewriter.
2. Place the typewriter in a large plastic bag.
3. Place at least 2” of packing material in the
bottom of the box for cushioning.
4. Place the typewriter inside the box and fill
the sides and top with more packing
material (2” of material on all sides).
5. Seal carton using either filament tape or
wide plastic tape.
6. Address the package for shipment to the
nearest service location. Remember to
include your return address and retain
your shipping receipt.
Important Information
Safe Operating
Recommendations
To avoid unnecessary operator injury or
damage to the machine, please review the
following recommendations.
• USE THE CORRECT VOLTAGE to avoid
electrical short circuiting, overheating or
shocks.
• If in doubt, check the electrical rating
label affixed to the unit. Smith Corona
does not recommend attaching your unit
to any power source other than that
which is indicated on the original electric
rating label of the machine. Smith Corona
does not recommend the use of a voltage
converter.
• THE UNIT SHOULD BE PLUGGED into an
outlet which is nearby and easily
accessible.
• ALWAYS HAVE THE UNIT SERVICED by a
qualified service technician. There are no
user-serviceable parts inside.
• TO AVOID ELECTRICAL SHOCK, never
insert metal objects such as screwdrivers,
paper clips, nail files, etc. inside the unit.
For safety’s sake, never place any object
inside the unit.
• BEFORE REACHING INTO THE CARRIER
PATH AREA, always switch to standby or
off, depending on the model.
• KEEP FINGERS, HAIR, JEWELRY, etc.
away from the carrier area when in
operation.
• IF THE UNIT IS DROPPED, the insulation
system may be disturbed. Have the unit
checked by a qualified service technician
before using it again.
• DO NOT remove the housing from the
unit.
• AVOID PLACING THE UNIT near an
excessively warm or humid location.
• IF LIQUIDS ARE SPILLED OR SPLASHED
on the unit, immediately unplug it. Have
the unit checked by a qualified service
technician.
Reorient the receiving antenna.
Relocate the typewriter with respect to
the receiver.
Move the typewriter away from the
receiver.
Plug the typewriter into a different
outlet so that typewriter and receiver
are on different branch circuits.
If necessary, the user should consult the
dealer or an experienced radio/television
technician for additional suggestions. The
user may find the following booklet prepared
by the Federal Communications Commission
helpful: “How to Identify and Resolve Radio-
TV Interference Problems.”
This booklet is available from the U.S.
Government Printing Office, Washington, DC
20402, Stock No. 004-00-00345-4
Notice: Any modification or alteration of a
typewriter which allows electronic
communication with a computer or attaching
it to a receptacle or module interface which
is not recommended will void Smith Corona’s
warranty on this product to the extent that
any such modification may be related to a
failure. Some typewriters are not designed as
computer printers and when modified to
perform this function may be in violation of
the safety and emission rules and
regulations.
Note: This digital apparatus does not exceed
the class B limits for radio emissions from
digital apparatus as set out in the radio
interference regulations of the Canadian
Department of Communications.
For your convenience and protection make a
record of the model number and serial
number. The serial number is located on the
inside of the typewriter on the bottom right
side. Use these numbers when ordering
supplies and accessories and for
identification in case of theft.
Model Name_____________________________
Serial Number ___________________________
Date of Purchase ________________________

Termékspecifikációk

Márka: Smith Corona
Kategória:
Modell: MEMORY CORRECT

Szüksége van segítségre?

Ha segítségre van szüksége Smith Corona MEMORY CORRECT, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Smith Corona

Smith Corona

Smith Corona Wordsmith 150 Útmutató

21 Augusztus 2024
Smith Corona

Smith Corona Wordsmith 200 Útmutató

19 Augusztus 2024
Smith Corona

Smith Corona MEMORY CORRECT Útmutató

18 Augusztus 2024
Smith Corona

Smith Corona Office 2000 Memory Útmutató

16 Augusztus 2024
Smith Corona

Smith Corona Spellmate Electronic Typewriter Útmutató

16 Augusztus 2024
Smith Corona

Smith Corona Display Typewriter Útmutató

15 Augusztus 2024
Smith Corona

Smith Corona Wordsmith 100 Útmutató

14 Augusztus 2024

Útmutatók

Legújabb útmutatók

PCE Instruments

PCE Instruments PCE-889B Útmutató

16 Október 2024
PCE Instruments

PCE Instruments PCE-WSAC 50 Útmutató

16 Október 2024
PCE Instruments

PCE Instruments PCE-777N Útmutató

16 Október 2024
Jawbone

Jawbone Jambox Útmutató

15 Október 2024
Jawbone

Jawbone Up2 Útmutató

15 Október 2024
Kundo XT

Kundo XT CO2 Control Útmutató

5 Október 2024
Univers By FTE

Univers By FTE U5000 Útmutató

5 Október 2024
Master

Master CD 5000 Útmutató

21 Szeptember 2024
InterBar

InterBar 8115-004.01 Útmutató

17 Szeptember 2024
Fresh 'n Rebel

Fresh 'n Rebel Rockbox Fold 2013 - 1RB700 Luidspreker Útmutató

14 Szeptember 2024