Használati útmutató Selfsat Snipe Platinum

Selfsat Vevő Snipe Platinum

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Selfsat Snipe Platinum (134 oldal) a Vevő kategóriában. Ezt az útmutatót 10 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/134
ENGLISH - 3
•
•
•
•
•
•
•
Please also note the following instructions from the manufacturer :
1-2. Proper use and operation
This product has been designed for portable use or xed installation on vehicles with
maximum speeds of 130 km/h. The unit is programmed to automatically aims at geostation-
ary television satellites.
The power is supplied by a standard vehicle electrical system with a rated voltage of 12VDC.
For installations on the vehicle, use power input cable (cigarette lighter cable) to supply
power.
For portable use, optional power adaptor produced by manufacturer must be used.
1-3. Safety notes
Please carefully read and follow the operating instructions in this manual and use the
SNIPE PLATINUM for its intended purpose.
Upon installation of SNIPE PLATINUM, please ensure the installation is done with
supplied cables and ensure the cables are not modied in any way.
As the user of this equipment, be responsible for ensuring compliance with the relevant
laws and regulations.
The manufacturer does not take liability for direct or indirect consequential damage of
the system, motor vehicles or other equipment by reason of unsuitable battery usage or
erroneous installation or wrong wire connection.
It is not possible to add or remove components on this product.
The use of other components other than those originally supplied is not permitted.
To complete installation, installer must strictly follow instruction in the supplied user manual.
Failure to follow the user manual may cause damage to the unit or user's vehicle.
The product does not require any regular maintenance; all service must be carried out at
approved service centers.
All relevant guidelines of the automotive industry must be observed and complied with.
The equipment must only be installed on solid vehicle roofs.
Avoid cleaning user's vehicle with the mounted satellite system in a drive-through car wash or
a car wash with a high-pressure cleaner.
ENGLISH - 4
2. Contents
2-1. Accessory included
Actual components may dier from the above images.
The unit enables to have power from car battery. To make power input cable for
direct connection, cut o cigarette lighter adaptor and peel o to take copper
cables out.
Only power adaptor produced by SNIPE series manufacturer is guaranteed and
has be used.
Power adaptor has to be purchased separate. Please ask to local dealer/shop for
more information.
※
※
※
※
Main unit Mounting plate
Cable glandCable holder
PI box
Remote control bracketRemote control
M6 × 15(8), M4 ×20(14)
User manualAllen wrench Power adaptor
(Optional)
Cigarette lighter adaptor Signal cable - 12 m
(x2 for twin outputs)
PI cable - 1.5m Base pads
ENGLISH - 5
2-2. Name of parts
Main unit
Latch
Antenna
LNB
Skew pivot
to PI (ANT Port)
to Receiver (optional)
Elevation
Main body
Base
Mounting plate
PI box Remote control
HOME LED
POWER LED
HOME button
POWER button
Fixed hole
Power
to STB
to unit
Display window
BT button
Power button
HOME button
SET button
Arrow button
DiSEqC button
Bracket
Pairing antenna
with remote control
ENGLISH - 7
HOME LED
POWER LED
HOME button
POWER button
Power
Fixed hole
to STB
to unit
3-2. Functional description
1. PI box
A. HOME Button / HOME LED (Blue)
C. Basic Features
When the Home button is pressed, the antenna moves to the home position
HOME LED turn on when the antenna is in the home position, and Blink when the antenna is
move to home from another position
i.
ii.
Press the POWER button to turn on the PI box, and power to the antenna unit
a.
i. POWER ON / LED ON
ii. POWER OFF / LED OFF
B. POWER Button / POWER LED (Red)
n order to turn o the PI power, you must rst turn o the STB power
When the power of the STB is turned o, Press and hold for more than 3 seconds to turn o the
power. (Power LED OFF)
- At this time, if the antenna is not in the home position (e.g. when towards the satellite), the
power is turned o after the antenna is moved to the home position
If the STB is not powered o, the PI BOX does not turn o even when the power button is
pressed, and the POWER LED ashes to indicate that the STB Power is ON.
- At this time, the PI does not turn o, and only the antenna moves to the home position
a.
b.
c.
i. Power save mode
When receiving a broadcast signal or when the antenna is in the home position, the antenna
operates only with the current from the STB
When searching for a satellite or when the antenna moves, it automatically changes to the power
connected to DC power adapter
a.
b.
ENGLISH - 8
Display window
BT button
Power button
HOME button
SET button
Arrow button
DiSEqC button
Bracket
Pairing antennas with remote controls
When not used for more than 15 seconds, it
enters the power saving mode.
(When the battery is inserted in the remote
control)
To return from sleep mode, press only SET
button
i.
ii.
2. Remote control
A. Sleep mode – battery save mode
When use antenna and remote control for the rst time or when you delete the
antenna list stored in the remote control, a list of products that can be connected
will appear.
Press the left and right buttons on the remote control to select the MAC Address of
your antenna unit, and press the SET button to connect to the remote control
SNIPE PLATINUM has two MAC addresses, so need to choose exactly according to
the use
MAC address of PI BOX of SNIPE PLATINUM
When use antenna and remote control for the rst time,
must select a MAC address starting with WP
SELECT MAC
WP - E9 : FC : E4
PRESS SET
Delete the MAC Address of antenna stored in the remote control.
Used to connect to other products
BT SET
REMOVE MAC
PRESS SET
WP - XX : XX : XX
MAC address starting with WM used for special
operations and should not be selected in general
situations.
For details, refer to [G. Additional function].
WM - XX : XX : XX
When using general operations,
it is displayed abbreviated on
the remote control screen
W - XX : XX : XX W - XX : XX
or
Press BT button to change to BT setting screen. Press the arrow to move to the desired function
and set with the SET button
Press and hold BT button for more than 5 seconds to reset the remote control
a.
b.
i. BT button
B. BT Setting

Termékspecifikációk

Márka: Selfsat
Kategória: Vevő
Modell: Snipe Platinum

Szüksége van segítségre?

Ha segítségre van szüksége Selfsat Snipe Platinum, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Vevő Selfsat

Selfsat

Selfsat Snipe Dish 85 Útmutató

29 December 2024
Selfsat

Selfsat Snipe Dish 65 Útmutató

29 December 2024
Selfsat

Selfsat Snipe Dome Útmutató

23 Augusztus 2024
Selfsat

Selfsat Caravan Plus Útmutató

22 Augusztus 2024
Selfsat

Selfsat Snipe Mobil Camp Útmutató

22 Augusztus 2024
Selfsat

Selfsat Snipe Air Útmutató

22 Augusztus 2024
Selfsat

Selfsat Snipe Platinum Útmutató

22 Augusztus 2024

Útmutatók Vevő

Legújabb útmutatók Vevő

Yamaha

Yamaha Aventage RX-A4A Útmutató

9 Április 2025
Yamaha

Yamaha Aventage RX-A8A Útmutató

9 Április 2025
DJI

DJI D-RTK 3 Útmutató

5 Április 2025
Phonocar

Phonocar PH544 Útmutató

5 Április 2025
QSC

QSC SPA-Qf 60x2 Útmutató

2 Április 2025
Harper

Harper HDT2-5010 Útmutató

2 Április 2025
Harper

Harper HDT2-2010 Útmutató

2 Április 2025
Alpine

Alpine MRX-F65 Útmutató

31 Március 2025
Streacom

Streacom TL1 Útmutató

31 Március 2025
Pro-Ject

Pro-Ject Stereo Box DS Útmutató

30 Március 2025