Használati útmutató Sauter TG 1250-0.1FN

Sauter Mérőberendezések TG 1250-0.1FN

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Sauter TG 1250-0.1FN (10 oldal) a Mérőberendezések kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/10
Sauter GmbH
Ziegelei 1
D-72336 Balingen
e-mail: info@kern-sohn.com
Phone : +49-[0]7433- 9933-0
Fax: +49-[0]7433- - 9933 149
Internet: www.sauter.eu
Instruction Manual Digital Coating
Thickness Gauge
SAUTER TG/TF
Version 2.0
04/2020
GB
TG_TF- -e-2020 BA
PROFESSIONAL MEASURING
TF 1250-0.1FN
TG 1250-0.1FN
2 TG_TF- -e-2020 BA
SAUTER TG/TF
V. 2.0 04/2020
Instruction Manual Digital Coating Thickness
Gauge
Thank you for purchasing a digital coating thickness gauge from SAUTER. We hope
you will be very satised with the high quality of this measuring device and its extensive
functionality. For any questions, wishes and suggestions please do not hesitate to
contact us.
Table of contents:
1. Introduction .................................................................................................... 3
2. Functions ........................................................................................................ 3
3. Technical data ................................................................................................ 4
4. Front panel description ................................................................................. 5
5. Measurement procedure ............................................................................... 6
6. Statistics ......................................................................................................... 6
7. How to store and recall readings 7..................................................................
8. How to delete readings .................................................................................. 7
9. Transfer of readings to a PC......................................................................... 7
10. Calibration ...................................................................................................... 8
11. Battery replacement ...................................................................................... 8
12. Adjustment foils ............................................................................................. 8
13. Correct handling at Coating Thickness Measurement with external
sensors ...................................................................................................................... 9
14. Trouble shooting 9............................................................................................
15. Restore factory settings ................................................................................ 9
16. Annotations .................................................................................................. 10
TG_TF- -e-2020 3 BA
1. Introduction
1.1 General description
This coating thickness gauge is small, light and handy. Although it has complex and
advanced equipment, it is convenient and easy to use.
Its robustness allows it to be used for many years, provided that all instructions in this
manual are carefully followed.
Therefore please keep them always within reach!
Note: It is strongly recommended to adjust the new meter before rst use, as
described in chapter 6. This will result in a higher measurement accuracy from
the beginning.
2. Functions
"This device complies with ISO 2178 and ISO 2361, as well as DIN, ASTM and BS
standards. This means that it can be used both under laboratory conditions and under
rough environmental conditions "in the eld".
"In F mode, the thickness of non-magnetic layers, e.g. paint, plastic, enamelled
porcelain, copper, zinc, aluminium, chrome, lacquer layers etc., is measured.
These layers should be on magnetic materials such as steel, iron, nickel, etc. This test
method is often used to measure the thickness of galvanised layers, lacquer layers,
enamelled porcelain layers, phosphorescent layers, copper plates, aluminium plates,
alloys, paper etc.
"In the N- mode, the layer thickness of non-magnetic layers on non-magnetic metals.
It is used to measure anodizations, lacquer layers, glazes, colours, enamel, plastic
layers, powder coating etc. These should be on non-magnetic substrates such as
aluminium, sheet metal, non-magnetic stainless steel and others.
"Automatic recognition of the carrier material
"Manual or automatic switch-o to conserve battery power.
"Two measurement modes: -single and continuous
"Metric/imperial unit conversion
"Wide measuring range and high resolution
"The backlit display allows accurate reading
"Up to 99 measured values can be stored.
"A statistics function is available
" Can be connected to a PC for data transfer via RS 232 interface for statistical
purposes Cable and software are available as optional accessories (ATC-01). .

Termékspecifikációk

Márka: Sauter
Kategória: Mérőberendezések
Modell: TG 1250-0.1FN

Szüksége van segítségre?

Ha segítségre van szüksége Sauter TG 1250-0.1FN, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Mérőberendezések Sauter

Sauter

Sauter FH 500 Útmutató

30 Március 2025
Sauter

Sauter FH 100 Útmutató

30 Március 2025
Sauter

Sauter TVS 20KN100 Útmutató

30 Március 2025
Sauter

Sauter CJ P4PG Útmutató

30 Március 2025
Sauter

Sauter DA 5-3 Útmutató

30 Március 2025
Sauter

Sauter SD 50N100 Útmutató

30 Március 2025
Sauter

Sauter LB 200-2 Útmutató

30 Március 2025
Sauter

Sauter TVM 20KN120N Útmutató

30 Március 2025
Sauter

Sauter CJ P2 Útmutató

8 Január 2025
Sauter

Sauter 289-100 Útmutató

8 Január 2025

Útmutatók Mérőberendezések

Legújabb útmutatók Mérőberendezések

Uni-T

Uni-T UT220 Útmutató

3 Április 2025
Uni-T

Uni-T UT681C Útmutató

3 Április 2025
Uni-T

Uni-T UT216C Útmutató

3 Április 2025
Uni-T

Uni-T UT611 Útmutató

3 Április 2025
Uni-T

Uni-T UT210D Útmutató

3 Április 2025
Uni-T

Uni-T UT210C Útmutató

3 Április 2025
Uni-T

Uni-T UT210B Útmutató

3 Április 2025
Uni-T

Uni-T UT682 Útmutató

3 Április 2025
Uni-T

Uni-T UT275 Útmutató

3 Április 2025
Uni-T

Uni-T UT08A Útmutató

3 Április 2025