Használati útmutató Sauter HB0 100-0

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Sauter HB0 100-0 (7 oldal) a Mérőberendezések kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/7
Sauter GmbH
Ziegelei 1
D-72336 Balingen
e-mail: info@kern-sohn.com
Phone : +49-[0]7433- 9933-0
Fax: +49-[0]7433- - 9933 149
Internet: www.sauter.eu
Instruction manual analog shore
hardness tester
SAUTER (&TI) HB
Version 2.0
03/2020
GB
HB- -e-2020 BA
PROFESSIONAL MEASURING
2 - -e-2020 HB BA
GB
Thank you for purchasing the analogue Shore hardness tester from SAUTER. We
hope you will be very satised with the high quality of the hardness tester and its
functionality. For any questions, wishes and suggestions we are at your disposal.
Table of contents:
1 Before commissioning .................................................................................. 3
2 General overview ........................................................................................... 3
3 Technical data ................................................................................................ 4
4 Measurement method .................................................................................... 4
5 Storage ........................................................................................................... 4
6 SHORE DUROMETER TEST STAND with HB .............................................. 5
7 Introduction .................................................................................................... 5
8 Structure ......................................................................................................... 5
9 Operation ........................................................................................................ 6
10 Note ................................................................................................................. 7
11 Maintenance ................................................................................................... 7
HB- -e-2020 3 BA
1 Before commissioning
Before putting the device into operation, check the delivery for any transport damage
to the packaging, the plastic case and the device itself. Should this be the case,
SAUTER must be contacted immediately.
2 General overview
The hardness of plastic is generally measured with a Shore hardness tester, using
either the or the scale. This is the preferred method for rubber or Shore A Shore D
elastomers and also for "softer" plastics such as polyolens, uoropolymers and vinyl.
The Shore A scale is used for "softer" rubbers and the Shore D scale for the "harder"
rubbers.
Shore C/ Shore 0 is mainly used for tests with foam rubber, sponges, microporous
plastic, etc.
These three dierent tips (see gure above) are not interchangeable. For each
hardness range the corresponding Shore hardness tester must be purchased.
Developed according to the following standards:
DIN 53505
ASTM D2240
ISO 868
This Shore hardness tester is especially recommended for internal comparison
measurements. Standard calibrations, e.g. to DIN 53505, are often not possible due to
very tightly specied standard tolerances and are therefore not oered by SAUTER.
Shore A, Shore C / Shore 0 and Shore D

Termékspecifikációk

Márka: Sauter
Kategória: Mérőberendezések
Modell: HB0 100-0

Szüksége van segítségre?

Ha segítségre van szüksége Sauter HB0 100-0, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Mérőberendezések Sauter

Sauter

Sauter FH 500 Útmutató

30 Március 2025
Sauter

Sauter FH 100 Útmutató

30 Március 2025
Sauter

Sauter CJ P4PG Útmutató

30 Március 2025
Sauter

Sauter DA 5-3 Útmutató

30 Március 2025
Sauter

Sauter SD 50N100 Útmutató

30 Március 2025
Sauter

Sauter LB 200-2 Útmutató

30 Március 2025
Sauter

Sauter CJ P2 Útmutató

8 Január 2025
Sauter

Sauter 289-100 Útmutató

8 Január 2025

Útmutatók Mérőberendezések

Legújabb útmutatók Mérőberendezések

Uni-T

Uni-T UT220 Útmutató

3 Április 2025
Uni-T

Uni-T UT681C Útmutató

3 Április 2025
Uni-T

Uni-T UT216C Útmutató

3 Április 2025
Uni-T

Uni-T UT611 Útmutató

3 Április 2025
Uni-T

Uni-T UT210D Útmutató

3 Április 2025
Uni-T

Uni-T UT210C Útmutató

3 Április 2025
Uni-T

Uni-T UT210B Útmutató

3 Április 2025
Uni-T

Uni-T UT682 Útmutató

3 Április 2025
Uni-T

Uni-T UT275 Útmutató

3 Április 2025
Uni-T

Uni-T UT08A Útmutató

3 Április 2025