Használati útmutató Quantum EC-LLHAE-YF

Quantum nincs kategorizálva EC-LLHAE-YF

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Quantum EC-LLHAE-YF (210 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/210
81-81317-07 B01
SuperLoader™ 3
SuperLoader 3
User’s Guide User’s Guide User’s Guide User’s Guide User’s Guide User’s Guide User’s Guide
.
Quantum SuperLoader 3 Quick Start Guide
Quantum SuperLoader 3 Quick Start Guide
ON
Home
ON
Home
Settings>Control Panel>System>Hardware>Device Manager>Tape
Drive Media Changer
Function Green Amber
OFF OFF
Command Status
Commands Enter
Commands Log Out
Enter Session Complete
Escape Escape
ON OFF
Flashing OFF
OFF Flashing
OFF ON
Enter Eject
Load Unload
Security
Commands Enter
Commands Enter Enter
Enter EnterTo Drive
Insert Tape, Push Until Prompted
Insert Tape, Push Until Prompted
Tape Loaded
Enter
Missed Tape
Exit
Commands Enter
Commands Enter Enter
Enter To Location Enter
Insert Tape, Push Until Prompted
Insert Tape, Push Until Prompted
Tape Loaded
Enter
Missed Tape
Exit
Commands Enter
Commands Move Enter
Move From:
*
* Enter
Enter
No Source Element
Destination Full
Commands Enter
Commands Eject Enter
Eject Tape, Mailslot
Enter
By Barcode
Enter
Commands Enter
Commands Eject Enter
Eject Tape Mailslot
Enter
By Location
*
@ Auto Clean
Enter
Commands Enter
Commands Eject Enter
Eject Cartridge Enter
From Drive Enter
Commands Enter
Commands Eject Enter
Eject Right Magazine Left Magazine
Enter
Left magazine has been
ejected Right magazine has been ejected
Left Mag Inserted Right
Mag Inserted
6/14
3/11
6/14
3
/1
1
Status Enter
Status Autoloader Enter
Autoloader Status Enter
Status Enter
Status Autoloader Enter
Autoloader Element Status
Enter
Enter
*
!
@
Enter
Element Status
Move
To: Enter
Escape
Status Enter
Status Drive Enter
Drive Enter
Status Enter
Status Drive Enter
Drive Version Enter
Status Enter
Status Ethernet Enter
Commands Enter
Commands Inventory
Enter
DHCP
Enabled Disabled.
Diagnostic
Diagnostic
Diagnostic
Commands
Configurations
Diagnostics Updates
Home
Allow META
REFRESH
Tools>Internet Options
Security
Home
Updates
Refresh
Status
guest
guest
Nov/21/2004 19:28
POC:00121,
POH:00002:07:45
submit
Configurations
System Operations Networking Security
System Operations SCSI ID (or Fibre
Channel) SAS Mode Compression Cleaning Tape Magazines
System Time
Configurations Configurations
System Operations SCSI ID
submit
Configurations Configurations
System Operations Fibre Channel
Fibre Channel Topology.
Fibre Channel Speed
submit
SAS
Configurations Configurations
SAS
submit
Random Sequential
Random
Random
Sequential
Sequential
Device Manager
Device Manager Random
Sequential Cycle Sequential
Sequential Cycle
Mode
Configurations Configurations
Mode
Sequential Cycle
Sequential
submit
Configurations Configurations
Compression
Compression Enabled
Compression Disabled
Auto Clean
None
Commands
Auto Clean
Auto Clean
Auto Clean
Configurations Configurations
Cleaning Tape
Auto Clean
Auto Clean
Auto Clean
Auto Clean
Cleaning Tape Location
Auto Clean
submit
Both
Left Right
Left Right
Magazines
Configurations Configurations
Magazines Magazines
Magazines Esc
Magazines
submit Both Right
Left
This will require a power cycle and ISV configuration
change. Enter To Continue
submit Please
power cycle the tape autoloader and reconfigure the ISV app.
Time Zone
Time Zone Month
Day
Year
Hour
Minute
submit
Current Network Parameters Set IP Set Network Configuration
Current Network Parameters
Configurations Configurations
Configurations Networking
Current Network Parameters
Set IP DHCP
Set IP
DHCP
< >Tab
DHCP
< >Tab
DHCP
Set Network Configuration
< >Tab
submit
submit
Select User Type
Select User Type submit
User Name Password
Client Authorization Control
Configurations Configurations
Security
Client Authorization Control
Enable Disabled
submit
Client Overlap Control
No Locking Full
Locking Time-Based Locking
No Locking
Full Locking
Home
Time-Based Locking Full Locking
submit
Configurations Configurations
Security
Client Overlap Control
No locking
Full Locking
Time-based Locking
Home
submit
Restore Default
Configuration Menu
Updates Firmware Update
Browse
.img
Upload
OK
Initialization
Diagnostics
Diagnostics Diagnostics
View Error and History Logs View Logs
Save Logs
View Logs
Save Logs
Home
Diagnostics Diagnostics
Diagnostics
Test
Start Test
View Diagnostic Test Progress View Status
View Diagnostic Test
Progress View Status
Identification
Diagnostics Diagnostics
Identification Time (secs)
Identify
System Reset
Diagnostics Diagnostics
System Reset System Reset
Commands
Commands
Commands Commands
Moving Tapes
From:
To:
submit
Commands Commands
Commands Inventory
Moving Tapes
Inventory Set to Home
Set to Home
Home
1Commands Commands
2Commands Set to Home
Sequential Operations Sequential Operations
Note: Sequential
Configurations Sequential Operations
1Commands Commands
2Commands Sequential Operations
3Sequential Operations Start
Sequential Operations Stop
Sequential Operations Resume
Note: Start Resume
Chapter 5 Administration
Configuring the Autoloader
62 Quantum SuperLoader 3 User’s Guide
Note: The front panel requires a six-digit password to change the
configuration (see “ Setting Passwords” on page 74). The LCD
front panel default password for the Administrator is 000000.
The default password for the Operator is 111111.
• If the autoloader does not power on successfully, check the
following:
• Power switch is on.
• Power cable is inserted correctly.
• SCSI (or SAS, or Fibre Channel) cable is connected to the
autoloader and host computer.
• SCSI bus is terminated (SCSI autoloader).
• No error code displays on the autoloader LCD.
• If you cannot resolve the problem yourself, contact your service
representative or go to www.quantum.com .
When you first power on the autoloader, the setting for the Internet
Protocol (IP) address is static with the address 192.168.20.128. If you
want to use Dynamic Host Configuration Protocol (DHCP) to change the
IP address, see “ Setting the IP Address” on page 67. To determine the IP
address when using DHCP, view the Ethernet status information (see
“Viewing Ethernet Information” on page 40).
Configuring the Autoloader
To configure the autoloader, start with the main menu on the front
panel. If the main menu is not already visible on the LCD, press Enter.
When you first power on the autoloader, the default is set with no
password protection. However, after you set the security option, all the
configuration functionality is password-protected. You need an
administrator-level password to configure the autoloader.
To configure the Quantum SuperLoader 3 autoloader, you must verify
the setup of the following:
• SCSI, SAS, or Fibre Channel autoloader.
SCSI ID
Diagnostics
Error Logs
Hard
Tape Alert Logs
End Curr. Test
Picker Test
Magazine Test
Inventory Test
Last Test Log
Random Moves
Eject
Tape (Mailslot)
By Barcode
By Location
From Drive
Right Magazine
Left Magazine
Enter (Mailslot)
Autoloader
Autoloader
Autoloader
Commands
To Drive
To Location
Move
Inventory
Enter Password
Operator
Administrator
Log Out
Home
Resume
Start
Stop
Sequential Ops
Autoloader
Status
Version
Element Status
Drive
Status
Version
Ethernet
Status
IPv6 Link Local
Enter To View
Configuration
SCSI ID
Set Topology
Set FC Speed
Set Loop Id
SAS
Fibre Channel
Fibre Channel
Set TLR
Ethernet
Set IPv4 Addr
Set IP
Set Gateway
Set Subnet Mask
Set IPv6 Addr
Set IP
Time
Set Timezone
Set Date/Time
Change Mode
Random
Sequential
Cleaning Tape
Auto Clean
Magazines
Left
Both
Right
Security
Security
Set Password
Operator
Administrator
Restore Default
Seq Cycle Mode
Barcode Reader
SCSI Barcode
or
or
Enter
Configuration Enter
Configuration SCSI ID Enter
Enter Cycle Power new SCSI ID
System
Shutdown wait 60 sec Power Off
SAS SCSI ID.
Enter
Configuration Enter
Configuration SAS Interface
Enter
Enable or Disable
transport layer retries Enter
Please
Cycle Power
Power Off
Fibre Channel
SCSI ID.
Enter
Configuration Enter
Configuration Fibre Channel
Enter
Set Topology Set
FC Speed Set Loop ID Enter
Set Topology Auto Negotiate Loop P2P
Set FC Speed Auto Negotiate 1 Gig 2 Gig
Set Loop ID 0 – 127Loop ID Loop
Set Topology)
Please
Cycle Power
Power Off
0.0.0.0
255.255.255.255
Configuration Enter
Configuration Ethernet
Enter
Ethernet Set IP Enter
DHCP Enter Please reboot to use DHCP
System
Shutdown wait 60 sec Power Off
Configuration Enter
Configuration Ethernet
Enter
Ethernet Set IP Enter
Static IP Enter
Enter
Enter to save
Chapter 5 Administration
Setting Ethernet
68 Quantum SuperLoader 3 User’s Guide
Note: If you make a mistake, press Escape to backspace to the
digit you want to change.
6 Press Enter. The Configuration submenu appears and the static IP is
now in effect. You do not need to reboot the autoloader.
7 Press Escape or Enter to return to the Ethernet submenu.
Setting the Subnet
Mask
Creating a subnet mask is a method of splitting IP networks into a series
of subgroups, or subnets, to improve performance or security.
To set a subnet mask:
1 From the main menu, scroll to Configuration, and then press Enter.
2 From the Configuration menu, scroll to Ethernet, and then press
Enter.
3 From the Ethernet submenu, scroll to Set Subnet Mask, and then
press Enter.
4 At each position of the Subnet Mask address, use the up and down
arrows to change the value of each digit. Press Enter to advance the
cursor to the next digit.
When you have advanced through all of the digits of the subnet
mask address, the autoloader displays Enter to save.
Note: If you make a mistake, press Escape to backspace to the
digit you want to change.
5 Press Enter. New Subnet Mask xxx.xxx.xxx appears on the LCD. You
do not need to reboot the autoloader.
6 Press Escape or Enter to return to the Ethernet submenu.
Setting an IP Gateway To set an IP gateway:
1 From the main menu, scroll to Configuration, and then press Enter.
2 From the Configuration menu, scroll to Ethernet, and then press
Enter.
Ethernet Set Gateway
Enter
Enter
Enter to save.
Escape
Enter New Gateway is xxx.xxx.xxx
Escape Enter
POC: 00121, POH: 00002:07:45
Configuration Enter
Configuration Time Enter
Time Set Timezone
Enter Time Zone
Enter
Chapter 5 Administration
Setting the Change Mode
70 Quantum SuperLoader 3 User’s Guide
Press Escape or Enter as necessary to return to the main menu.
To set the date and time:
From the main menu, scroll to Configuration, and then press Enter.
From the Configuration menu, scroll to Time, and then press Enter.
From the Time submenu, scroll to Set Date/Time, and then press
Enter. The Date/Time screen appears, allowing you to set the date
and time. The cursor automatically appears at the first digit.
The first four digits represent the current year. At each position of
the year, use the up and down arrows to change the value of each
digit. Press Enter to advance the cursor to the next digit.
The next two digits represent the current month. At each position of
the month, use the up and down arrows to change the value of
each digit. Press Enter to advance the cursor to the next digit.
The next two digits represent the current day. At each position of
the day, use the up and down arrows to change the value of each
digit. Press Enter to advance the cursor to the next digit.
The next two digits represent the current hour. At each position of
the hour, use the up and down arrows to change the value of each
digit. Press Enter.
The last two digits represent the current minute. At each position of
the minute, use the up and down arrows to change the value of
each digit. Press Enter to advance the cursor to the next digit.
Press Enter to save.
Press Escape as necessary to return to the main menu.
You can set the autoloader to either Random or Sequential. The default
change mode is Random.
Random
Sequential
Note: Sequential
Device Manager
Device Manager Random
Seq Cycle Sequential
Seq Cycle
Change Mode
1Configuration Enter
2Configuration Change Mode
Enter
3
Escape
Enter Reboot to enable new
mode
4System
Shutdown wait 60 sec Power Off
Chapter 5 Administration
Setting the Change Mode
72 Quantum SuperLoader 3 User’s Guide
5 Press the power button again to power up the autoloader. The new
change mode is now in effect.
Sequential Mode
Operations
If you enable Sequential mode, you must use the Sequential Ops
submenu under the Commands menu to operate the autoloader after
you reboot.
• The Start command allows you to load the first cartridge.
• The Resume command allows you to continue from the next unused
slot, if a user stopped the cycle.
• The Stop command allows you to stop the cycle.
To start Sequential mode operation:
1 From the main menu, scroll to Commands, and then press Enter.
2 From the Commands menu, scroll to Sequential Ops, and then press
Enter.
3 From the Sequential Ops menu, scroll to Start, and then press Enter.
Moving first tape to drive appears on the LCD.
To stop Sequential mode operation:
1 From the main menu, scroll to Commands, and then press Enter.
2 From the Commands menu, scroll to Sequential Ops, and then press
Enter.
3 From the Sequential Ops menu, scroll to Stop, and then press Enter.
Ejecting tape from drive appears on the LCD.
To resume Sequential mode operation:
1 From the main menu, scroll to Commands, and then press Enter.
2 From the Commands menu, scroll to Sequential Ops, and then press
Enter.
3 From the Sequential Ops menu, scroll to Resume, and then press
Enter. Moving next tape to drive appears on the LCD.
Chapter 5 Administration
Setting Passwords
Quantum SuperLoader 3 User’s Guide 75
If you forget the administrator-level password, you cannot access the
autoloader's functionality to enter a new password. In this case, you
must call customer support. When you call, have the autoloader
connected to the Ethernet and open On-board Remote Management.
You can reset front panel passwords to the factory defaults
from On-board Remote Management. However, if the On-
board Remote Management passwords are lost, you must
contact customer support. If you must contact customer
support, be at the host computer with On-board Remote
Management on line. From the main screen, click Configuration.
The enter Network Password or User name screen displays. The
customer support representative will need the number
surrounded by asterisks to locate and reset your password. This
is your “realm number.”
Chapter 5 Administration
Setting Passwords
76 Quantum SuperLoader 3 User’s Guide
Quantum SuperLoader 3 User’s Guide 77
Chapter 6
This chapter provides troubleshooting information that might be helpful
with problems encountered during autoloader operation.
•Power-on Self Test (POST)
•Diagnostic Tests from the Front Panel
•On-board Remote Management Diagnostic Tests
This section describes the POST and its various tests and also explains
how to perform diagnostic tests from the front panel and from the On-
board Remote Management interface.
The Power-on Self Test (POST) and diagnostic tests are helpful tools for
testing the autoloader’s functionality and for troubleshooting errors.
With the results from the POST and diagnostic tests, you can determine
how well the autoloader is working and locate any problems
Every time you turn on the autoloader, the POST checks all of the
autoloader’s basic components. If you experience problems with the
autoloader, the POST is a good method to determine if any major parts
are malfunctioning.
System Shutdown Please
Wait...
Chapter 6 Diagnostics
Diagnostic Tests from the Front Panel
Quantum SuperLoader 3 User’s Guide 79
While the POST is running, a progress indicator showing the name of
the test displays on the front panel. If the autoloader is working
properly, the message System Ready and the current configuration
display after the POST completes successfully.
If the autoloader is not working properly, error messages display on the
front panel (see “ Autoloader Logs” on page 103).
Diagnostic tests allow you to calibrate parts of the autoloader, check the
condition of parts, or test the autoloader’s functionality. From the front
panel, you can perform all of the diagnostic tests.
Use of the Diagnostic Commands from the On-board Remote
Management interface should not be issued while the
autoloader is being used by host applications. Only use the
Diagnostics Commands when the autoloader is known to be
idle and unavailable to host backup/restore applications.
The autoloader recognizes when the drive or autoloader is executing
host commands and will respond appropriately to prevent application
failures. A diagnostic command issued between host application
commands may not be recognized appropriately, resulting in a failed
application.
Because certain tests require you to manually insert a cartridge, you can
perform only some of the diagnostic tests using On-board Remote
Management (see “ On-board Remote Management Diagnostic Tests” on
page 82 ).
On-board Remote Management allows you to request all
diagnostic tests, but any tests that require a cartridge to be
inserted will time-out unless someone manually inserts the
cartridge at the appropriate time.
Administrator
To enter an Administrator password:
Commands Commands
Command Enter Password
Enter
Enter Password Administrator
Enter
Login
Enter
Escape
Submit Password
Enter
Enter Password
Halt
Test Halt Test
Halt Test
Escape
Diagnostics
Halt Test Enter. User Abort
Enter Diagnostics
Halt Test
Halt Test Diagnostics
Stop Test
View Status Test Stopped
Diagnostics Enter
Enter.
Administrator
Running Test
Test Successful
Test Failed
Administrator
Administrator
Up Down
Enter
Escape
Enter
Diagnostics Enter
Running Test
Test Successful
Test Failed
Enter Diagnostics
Diagnostics
Administrator
Enter Diagnostics
Diagnostics
Start Test
View Diagnostic
Test Progress View Status
Eject
Commands
Enter
Commands Eject Enter
Eject Right Magazine Left Magazine
Enter
Inside edge view of left
magazine
Outside edge view of left
magazine
Left magazine blank
Screws
3.4” [86 mm]
Support brackets
Support bracket screws
Long autoloader
brackets (74-60604-01)
Short autoloader
brackets (74-60604-03)
(74-60605-01)
Clip nut
Outer covers
of the rack
Rail Rail
Rail
1.75 in
(44.45 mm)
Clip nut
Outer cover of rack
Rear rail in rack
Support bracket
Clip nuts
Rack
screws
Support bracket
Autoloader bracket
Front rail
Tab (one
Autoloader (front)
Rack
screws
per side)
System Reset
Diagnostics
System Reset
1
Status
Drive Status
Configuration
Random
System Reset
Diagnostics System
Reset
System Reset
Diagnostics System
Reset
Hard Log
Soft Log
Hard Log
Update Log
Boot Log

Termékspecifikációk

Márka: Quantum
Kategória: nincs kategorizálva
Modell: EC-LLHAE-YF

Szüksége van segítségre?

Ha segítségre van szüksége Quantum EC-LLHAE-YF, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva Quantum

Quantum

Quantum Xcellis QXS-484 Útmutató

12 Január 2025
Quantum

Quantum CoPilot Útmutató

31 Augusztus 2024
Quantum

Quantum TRU-Balance 4 Útmutató

27 Augusztus 2024
Quantum

Quantum TRU-Balance 3 Útmutató

27 Augusztus 2024
Quantum

Quantum TC-L52BN-EZ Útmutató

22 Augusztus 2024
Quantum

Quantum Scalar i3 Útmutató

22 Augusztus 2024
Quantum

Quantum EC-LLHAE-YF Útmutató

22 Augusztus 2024
Quantum

Quantum TC-L51AN-BR Útmutató

22 Augusztus 2024
Quantum

Quantum LTO-2 Útmutató

22 Augusztus 2024
Quantum

Quantum Xcellis QXS-456 Útmutató

22 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
Soundstream

Soundstream VRN-64HBL Útmutató

10 Április 2025
Panasonic

Panasonic Lumix DMW-AC11 Útmutató

10 Április 2025
Planet

Planet PWR-240-48 Útmutató

9 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
Alpine

Alpine DP2-40C-BC Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025