Használati útmutató QTX Q1000

QTX Vevő Q1000

Olvassa el alább 📖 a magyar nyelvű használati útmutatót QTX Q1000 (4 oldal) a Vevő kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/4
Q-SERIES
POWER AMPLIFIERS
Item ref: 172.051UK, 172.052UK, 172.054UK, 172.05 5UK
User Manual
Version 1.1
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
Q240/Q480/Q600/Q1000 User Manual
Introduction
Thank you for choosing the QTX Q series power amplifiers as part of your sound reinforcement system. These
amplifiers are designed to offer high quality, dependable service for mobile and installed systems. Please read
this manual fully and follow the instructions to achieve the best results with your new purchase and to avoid
damage through misuse.
Warning
To prevent the risk of fire or electric shock, do not expose any of the components to rain or moisture.
If liquids are spilled on the casing, stop using immediately, allow unit to dry out and have checked by qualified
personnel before further use. Avoid impact, extreme pressure or heavy vibration to the case
No user serviceable parts inside Do not open the case refer all servicing to qualified service personnel. – –
Safety
• Check for correct mains voltage and condition of IEC lead before connecting to power outlet
• Ensure speaker leads are good condition with no short connections or damaged plugs
• Check impedance of speaker loads do not exceed the minimum stated load for the amplifier
• Do not allow any foreign objects to enter the case or through the ventilation grilles
Placement
• Keep out of direct sunlight and away from heat sources
• Keep away from damp or dusty environments
• When rack-mounting, ensure adequate support for the base of the amplifier and firm fixings for the front
• Ensure adequate air-flow and do not cover cooling vents at the front and rear of the amplifier
• Ensure adequate access to controls and connections
Cleaning
• Use a soft cloth with a neutral detergent to clean the casing as required
• Use a vacuum cleaner to clear ventilation grilles of any dust or debris build-ups
• Do not use strong solvents for cleaning the unit
Unpacking
Your QTX Q series amplifier should arrive in good condition with the appropriate mains IEC lead(s)
If any contents are missing or damaged, contact your dealer immediately.
Q240/Q480/Q600/Q1000 User Manual
Layout
1.
Cooling vents do not cover –
8.
2.
LED Clip indicators
9.
3.
Channel gain controls
10.
4.
Power on/off switch and LED
11.
5.
LED Signal indicators
12.
6.
IEC mains inlet and fuse holder
13.
7.
Voltage select or
Operation
Connect speaker cabinets to speaker outputs (8, 9 or 10 using good quality leads and ensure that the )
combined load on each channel is no lower than 4Ω (for speaker loads connected in parallel, Ω + Ω = 8 8 4Ω)
Connect each signal input from mixer or other line level source via the jack (11) or RCA (12) connectors on
the rear panel using good quality signal leads. The jack and RCA inputs are wired in parallel, so whichever is
not used for the input signal can be used to connect onto further amplifier inputs.
Connect the amplifier to the mains outlet, making sure that the IEC lead is earthed, in good condition and
connected securely. Ensure the correct voltage is selected on the rear panel voltage selector (7)
With channel gain controls turned fully down, switch the power switch (4) . (3) on
With mixer (or other signal source) levels turned down, gradually increase the amplifier’s channel gain controls
to the required level (normally full) and then gradually increase the signal level from the mixer or sound
source until sound can be heard through the speakers and then continue increasing up to the required level.
During use, the Signal LEDs (5 will illuminate to show that the signal is present. If the Clip LEDs illuminate ) (2)
more than very briefly, reduce the volume until they hardly light up at all. This will avoid distortion or
“clipping” through the speakers.
Before powering down, turn the channel gain controls fully down to avoid loud noises when switching off.

Termékspecifikációk

Márka: QTX
Kategória: Vevő
Modell: Q1000

Szüksége van segítségre?

Ha segítségre van szüksége QTX Q1000, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Vevő QTX

QTX

QTX Q240 Útmutató

4 Október 2024
QTX

QTX Q1000 Útmutató

11 Július 2024
QTX

QTX QA1000 Útmutató

9 Július 2024

Útmutatók Vevő

Legújabb útmutatók Vevő

Marshall

Marshall DSL1 Útmutató

11 December 2024
A-NeuVideo

A-NeuVideo ANI-0108POE-AU Útmutató

11 December 2024
Jensen

Jensen XDA95RB Útmutató

11 December 2024
AVMATRIX

AVMATRIX SD1121-12G Útmutató

11 December 2024
AVMATRIX

AVMATRIX SD1191 Útmutató

11 December 2024
ButtKicker

ButtKicker BKA1000-P Útmutató

11 December 2024
Phonic

Phonic NT2504 Útmutató

11 December 2024
Phonic

Phonic DMA8825 Útmutató

11 December 2024
Phonic

Phonic MAX 1000 Útmutató

11 December 2024
Phonic

Phonic XP 5000 Útmutató

11 December 2024