Használati útmutató QSC AD-C.SUB

QSC hangszóró AD-C.SUB

Olvassa el alább 📖 a magyar nyelvű használati útmutatót QSC AD-C.SUB (6 oldal) a hangszóró kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/6
Acoustic Design Series
Quick Start Guide
AD-C.SUB
AD-C.SAT
EXPLANATION OF SYMBOLS
The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death.
The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result in
damage to the equipment that may not be covered under the warranty.
The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of theprocedure.
The term "NOTE" is used to indicate additional useful information.
The intent of the lightning flash with arrowhead symbol in a triangle is to alert the user to the presence of un-insulated "dangerous"
voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans.
The intent of the exclamation point within a triangle is to alert the user to the presence of important safety, and operating and
maintenance instructions in this manual.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with a dry cloth.
6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
9. Do not use this apparatus in or near water or liquids.
10. Do not use any aerosol spray, cleaner, disinfectant or fumigant on, near or into the apparatus.
11. Adhere to all applicable, local codes.
12. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment installation.
Maintenance and Repair
Advance technology, e.g., the use of modern materials and powerful electronics, requires specially adapted maintenance and repair methods. To avoid
a danger of subsequent damage to the apparatus, injuries to persons and/or the creation of additional safety hazards, all maintenance or repair work
on the apparatus should be performed only by a QSC authorized service station or an authorized QSC International Distributor. QSC is not responsible
for any injury, harm or related damages arising from any failure of the customer, owner or user of the apparatus to facilitate those repairs.
Warranty
For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com
®
1
TD-001556-01-A1
*TD-001556-01*
2
TD-001556-01-A1
Install the AD-C.SUB Subwoofer
What's in the AD-C.SUB Box
(1x)
AD-C.SUB
(1x)
Grille
(3x)
Euro-
style plug
(4-pole)
(1x)
C-Ring
(2x)
Tile Rail
Screws
(sheet metal)
(2x)
Tile Rails
(1x)
Cutout
Template
(1x)
Terminal Cover
(1x)
Warranty
TD-000453
(1x)
Quick Start
Guide
TD-001556
Prepare Ceiling
Refer to Figure 1.
1. Use the supplied Cut-Out template to cut a 12 inch (305 mm) diameter
hole (1) in the ceiling where the loudspeaker is to be installed. For frame-
construction ceiling, skip to "Wire the Loudspeakers".
2. Install two V-rails (2), one on each side of the hole, and supported by the
suspended-ceiling support rails (3).
3. Install the C-ring (4) over the hole, using the V-rails as support. Make sure the
clips on the C-ring are properly fitted over the V-rail.
4. Use sheet-metal screws (5) to secure the C-ring to the V-rails.
Wire the Subwoofer
Refer to Figure 2.
1. Loosen the two screws (1) holding the wire-terminal cover
(2) to the body of the loudspeaker enclosure.
2. Pull the cover (2) up slightly in front, then pull away from
the enclosure.
3. Pass the wires through the conduit/stress-relief clamp
(3). Leave enough wire for making connections. Carefully
tighten the clamp (3) over the wires, or over the conduit if
it is used.
NOT: The wire-terminal cover has two
additional openings (4) that you can use if the
factory-selected opening causes conflict between
the wiring and the structure.
4. Wire the female Euro-style plugs as shown in Figure 3.
5. The Euro-style plugs are factory installed. If you remove
the connectors, make sure to re-tighten the screws
to secure the connections.
6. Slide the cover (2) over the connector and under the
two clips, then tighten the two Phillips screws.
Cut-Out Template
AD-C.SAT
— Figure 1 —
1
2
3
4
5
— Figure 2 —
2
3
1
1
4
4
— Figure 3 —
Input Thru Sat 1 Sat 2 Sat 3 Sat 4
Amp
3
TD-001556-01-A1
Mount the Subwoofer
Refer to Figure 5.
1. Use a small flat-tip screwdriver, or similar tool, to carefully pry the grille off the
loudspeaker housing giving you access to the dog-ear screws. The grille is
held on by magnets.
2. Make sure all four of the dog ears are turned in, up against the side of the
metal loudspeaker housing. Figure 5 (1) shows turned in, (2) shows the
dogear not turned in.
NOTE: The dog ears can be turned in at two places only. One
accommodates up to 2-inch thick ceiling material, the other
accommodates 1.25-inch thick material. See Figure 4. Use the one
most suitable to your installation.
3. Slide the Loudspeaker Housing up through the hole into the ceiling. Make
sure that the wiring does not get pinched or caught on anything.
4. Use a Phillips screwdriver to tighten all four of the dog-ear screws. As you
tighten the screws, the dog ears swing away from the housing and over the
ceiling material. Before the dog ears are completely tightened, make sure all
dog ears are properly positioned over the ceiling material.
CAUTION!: Do not overtighten the dog-ear screws!
Seismic Safety
WARNING!: Be sure to check and adhere to local building
codes for seismic requirements. If in doubt, consult an appropriate
engineer. Regardless of local building codes, QSC recommends
that you use the appropriate safety tethers for the installation.
Refer to Figure 6.
1. Attach appropriate safety tethers (1) to the tether tabs (2), on the back of the
loudspeaker enclosure, and to an appropriate part of the building's structure.
Set the Operating Mode
Refer to Figure 7
1. Use a small coin, or similar tool, to set the transformer tap (1) based on the requirements of
theinstallation.
2. Install the loudspeaker grill / tether.
— Figure 4 —
2” (50 mm)
Max
1.25” (31 mm)
Max
— Figure 5 —
1
2
— Figure 6 —
1
2
2
— Figure 7 —
50
100
25
12.5
4Ω
100
25Ω
50
N/A
4Ω
50
100
25
12.5
4Ω
100
25
50
N/A
4Ω
70 Volts
100 Volts
1

Termékspecifikációk

Márka: QSC
Kategória: hangszóró
Modell: AD-C.SUB

Szüksége van segítségre?

Ha segítségre van szüksége QSC AD-C.SUB, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hangszóró QSC

QSC

QSC MD-FP152-124r Útmutató

30 Március 2025
QSC

QSC PL-CA6 Útmutató

30 Március 2025
QSC

QSC PL-SUB15 Útmutató

30 Március 2025
QSC

QSC PL-SUB10 Útmutató

30 Március 2025
QSC

QSC MD-FP152-64r Útmutató

30 Március 2025
QSC

QSC PL-SUB12 Útmutató

30 Március 2025
QSC

QSC Wideline 10 WL2102-w Útmutató

13 Január 2025
QSC

QSC HF-63X1 Útmutató

8 Január 2025
QSC

QSC WL115-sw Útmutató

8 Január 2025
QSC

QSC AD-C42T Útmutató

8 Január 2025

Útmutatók hangszóró

Legújabb útmutatók hangszóró

Celly

Celly Ultraboost Útmutató

1 Április 2025
Muse

Muse MC-50 WI Útmutató

1 Április 2025
Audac

Audac ARCHI210 Útmutató

30 Március 2025
Audac

Audac ARCHI10 Útmutató

30 Március 2025
Prixton

Prixton Jaia Útmutató

30 Március 2025
Prixton

Prixton Jaia Max Útmutató

30 Március 2025
JBL

JBL sCl-4 Útmutató

29 Március 2025
LG

LG CD-969S Útmutató

28 Március 2025
LG

LG FFH-185AD Útmutató

28 Március 2025
Metronic

Metronic 477074 Útmutató

27 Március 2025