Használati útmutató Provision-ISR PR-HDoNet+

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Provision-ISR PR-HDoNet+ (4 oldal) a AV hosszabbító kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/4
PR-HDoNet + USER MANUAL
www.provision-isr.com
HDMI Extender over Cat5e/Cat6
I. Introduction
This HDMI Extender allows you to extend your HDMI signal over
standard Network cable.
While HDMI cables are expensive, inconvenient to wire and suffer
from very limited transmission distances Ethernet cables offers a
wonderful alternative.
PR-HDoNet+ enables you to extend HDMI signal to remote display
unit to a maximum of 60 meters over Ethernet cable while
maintaining your remote controller active (from the display unit
location).
II. Features:
1. Transmits HDMI signal up to 40m distance over single Cat5e and
up to 60m over single cat6 cable
2. HDMI 1.3 & 3D Support
3. 12Bit deep color and bandwidth of up to 225 MHz support
4. Support video resolution up to 1080P@60Hz
5. Support audio format: DTS-HD / Dolby- true HD / LPCM7.1 /
DTS / Dolby-AC3 / DSD
6. DC5Vpower supply is included
Note:Distancemaybe byaffected thecable quality, length
andotherenvironmental interferences.
III. Product interface pictures
Transmitter(Tx) Receiver(Rx)
Port name Description
HDMI IN/OUT HDMI signal input/output
UTP RJ45 port;
RST
According to the connected cable length to make adjustment
of RST (If you change your display unit and/or cable length,
you must use it)
EDID
EDID Copy button, Press 3 seconds to copy display
configuration from the transmitter. If there is no display after
connection to display connect, restore default by RST.
DC/5V Power adapter socket
LED indicator Description
PWR System power indicator
STA HDMI signal indicator
PR-HDoNet + USER MANUAL
www.provision-isr.com
IV. Specification
V. Installation Process:
1. Connect the provided DC/5V power supply to the power socket
of Tx (Transmitter) and Rx (Receiver) units
2. Connect the Tx unit to the display device by HDMI cable, and
hold the "EDID" button on the Tx unit for 3 seconds unit the
“STA” indicator start blinking.
3. Connect the Rx unit to the display device by HDMI cable (no
more than 10M)
4. Connect the Tx unit to the video source device by HDMI cable
(no more than 10M).
5. Connect between the Tx and Rx units using Cat5e/6 cable Up to
40M/60M.
6. Turn on the source device
7. If you change your display unit, please re-study by “EDID
button. (Repeat process 2)
8. If you change cable length, please press “RST” button to reset
the unit.
VI. Package Contents:
1. HDMI transmitter unit p2-x1 pcs
2. HDMI receiver unit p2-x1 pcs
3. Power adapter x 2 pcs
4. User manual p2-x1 pcs
Parameter Description
Video
Standard HDMI 1.3; HDCP 1.2
Maximum pixel clock 165MHz
Maximum data rate 6.75Gbps
Resolution 1920X1080@60Hz, 3D
Connector HDMI-A
Impedance 10
Ethernet Interface RJ45
Transmission distance CAT6---50m
Other
Power supply The power adapter: DC 5V/1A
Power consumption MAX 3W
Operating Temperature Operating: -5 ~ +70
Humidity Operating: 5% ~ 90%
Dimension 81*43*23mm

Termékspecifikációk

Márka: Provision-ISR
Kategória: AV hosszabbító
Modell: PR-HDoNet+

Szüksége van segítségre?

Ha segítségre van szüksége Provision-ISR PR-HDoNet+, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók AV hosszabbító Provision-ISR

Útmutatók AV hosszabbító

Legújabb útmutatók AV hosszabbító