Használati útmutató Premier Mounts ECM-3000

Premier Mounts Lapos panel támogatás ECM-3000

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Premier Mounts ECM-3000 (8 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 14 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/8

Elliptical Ceiling Mount for 37˝ to 63˝ Flat Panels

Model: ECM-3000

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

1321 S. State College Blvd., Fullerton, CA 92831 USA

Warranty, Garantie, Garantía, Garanzia, Garantie, Waarborg: http://www.mounts.com/warranty 9531- 000-001- 0X Rev.0

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

ECM-3000

Mounting

Bracket Arms

Decorative

Covers

Elliptical

Tilt Mount

Triple Mount

Structure Side Skirt Thread Depth

Indicator

M6 x 25mm

32˝ Allen Wrench

M4 x 16mmM4 x 25mm M5 x 16mm M5 x 25mm

M6 x 30mm M8 x 25mm M8 x 30mm M8 x 70mm Griplate™

Washers

AST-2446/2

x18

M8 x 16mm

Minimum four (4)

complete turns

Pan Philips

Threaded

Coupler

Mount

Lower Half

Upper Half

The ceiling should be capable of supporting a weight of at least ve times

the product weight. If not, the ceiling surface must be reinforced. Proper

installation procedure by qualied personnel as outlined in the installation

instructions must be adhered to.

Mounting hardware is not included with this product. Commercially

available hardware must be used for this installation. The hardware used

will depend on your installation environment (i.e. wood stud, concrete

surface, metal I-beam etc).

Separate the upper and lower halves of the AST-2446/2 by removing both

M8 screws and wave washers. Unpack the trio mount and place it on the

ground.

The set screw on the threaded coupler must be backed out in order for the

AST-2446/2 to be threaded into place.

Thread the lower half of the AST-2446/2 into the threaded coupler on the

trio mount. The lower half of the AST-2446/2 must be threaded fully until

the piece is safely secured to the threads, then tighten the screw back into

place. Use the screwdriver to tighten the set screw once the AST-2446/2

has been attached.

The following steps must be performed by a minimum of three people:

Two people lift the trio mount into place. Align the upper and lower halves

of the AST-2446/2. Slide the lower half/trio mount into the upper half of the

AST-2446/2.

It is recommended that the height, and location, of the ECM-3000 be

determined prior to performing the following steps.

Determine the mounting height. Align the M8 mounting holes on the upper

and lower halves of the AST-2446/2 and insert the M8 screws and wave

washers. Use the 516˝ wrench to tighten the M8 screws.

Verify that all hardware is secure and tight before proceeding to the next

section.

M4 x 30mm M5 x 30mm M6 x 16mm

M6 x 45mm M8 x 45mm

Universal Spacers

AST-2446/2

Lower Half

Upper Half

M8 Pan

Philips

Screw

Allen Wrench

x1 x3 x3 x6 x6

x18

x3 x1

x18x18 x18 x18

x18 x18 x18 x12 x24

x18 x18 x18

x72

x18 x18

Required for installation

Included components

Max Flat-Panel Capacity: 80 lb. each

Inverted

Projector

Figure 1

Figure 2 Figure 3

Thread Depth

Indicator

Thread Depth

Indicator

Depth MarkDepth Mark

Thread Depth

Indicator

Threaded

Insert

Marking the

Depth

ScrewScrew

Warranty: http://www.mounts.com/warranty

Garantie, Garantía, Garanzia, Garantie, Waarborg

Updates: The most up-to-date installation

guides can be found at mounts.com

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100 | Europe +44 (0) 24 7664 4105

9531-0 0 0 -001-0X Rev. 0

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

ECM-3000

Premier Mounts’ Griplate™ Washers are designed to accom-

modate the various M4, M5, M6 and M8 hole sizes required

by flat panels.

Do not place excessive pressure on the back of the flat

panel, as this may damage your flat panel.

The Griplate™ Washer must be installed between the head

of the mounting screw and the mounting bracket as shown.

Does your flat panel have:

Recessed mount points?

Uneven mount points?

A curved back?

Any obstruction near the mount point?

If Yes, you must install nylon spacers. Remove the mount-

ing brackets, Griplate™ washers, and mounting screws from

the back of the flat panel.

Insert the Thread Depth Indicator into the thread inserts

found on the bottom or top of the projector. Use a pencil to

mark the depth of the thread insert on the Thread Depth In-

dicator, as shown. Inser t the Thread Depth Indicator into the

remaining thread inserts to compare and verify their depth.

Locate the correct diameter screw for the thread insert.

If the screw you selected is longer than the mark on the

Thread Depth Indicator, as shown in Figure 2 and Figure 3,

do not use this screw. The screw length must not bypass

the mark.

Select another screw length until you find a screw that

comes closest to the mark without going past the mark.

Test each size of the screws provided.

The correct screws should thread easily into the mount point

and not pull out when tension is applied.

The optional M3 flat washers may be used to decrease the

screw depth of either the M2.5 x 12mm screws or the M3 x

16mm screws. Decrease the screw depth by placing an M3

flat washer inside the leveling barrel and then inserting the

mounting screw.

Termékspecifikációk

Márka:	Premier Mounts
Kategória:	Lapos panel támogatás
Modell:	ECM-3000

Szüksége van segítségre?

Ha segítségre van szüksége Premier Mounts ECM-3000, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Lapos panel támogatás Premier Mounts

Premier Mounts ECM-3763S Útmutató

18 Augusztus 2024

Premier Mounts RTM-L Útmutató

17 Augusztus 2024

Premier Mounts P4263F Útmutató

17 Augusztus 2024

Premier Mounts PRC-LA Útmutató

17 Augusztus 2024

Premier Mounts ECM-3763T Útmutató

16 Augusztus 2024

Premier Mounts EST100 Útmutató

16 Augusztus 2024

Premier Mounts MMA Útmutató

16 Augusztus 2024

Premier Mounts PRC Útmutató

16 Augusztus 2024

Premier Mounts FLIP-B Útmutató

15 Augusztus 2024

Premier Mounts MM-BE426 Útmutató

15 Augusztus 2024

Útmutatók Lapos panel támogatás

Legújabb útmutatók Lapos panel támogatás

Konig KNM-MM20 Útmutató

8 Április 2025

Ergotron Neo-Flex Widescreen Stand Útmutató

3 Április 2025

Ergotron Neo-Flex Cantilever Útmutató

3 Április 2025

Ergotron All-In-One Lift Stand Útmutató

3 Április 2025

Ergotron DS100 Dual Monitor Desk Stand Útmutató

3 Április 2025

Ergotron DS Series DS100 Quad Monitor Desk Stand, Horizontal Útmutató

3 Április 2025

Ergotron LX Series Desk Mount LCD Arm, Tall Pole Útmutató

3 Április 2025

Ergotron LX Series Dual Stacking Arm Útmutató

3 Április 2025

Ergotron 100 Series Double Pivot Útmutató

3 Április 2025

Ergotron Convert-to-LCD & Laptop Kit Útmutató

3 Április 2025