Használati útmutató Philips 27E1N5600E

Philips Monitor 27E1N5600E

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Philips 27E1N5600E (29 oldal) a Monitor kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/29
E1N5600E
5000 Series
Monitor
Register your product and get support at www.philips.com/welcome
EN
User manual 1
Customer care and warranty 19
Troubleshooting and FAQs 23
Table of Contents
1. Important ...................................... 1
1.1 Safety precautions and
maintenance 1 ..................................
1.2 Notational Descriptions 3 ..............
1.3 Disposal of product and packing
material 4 ............................................
2. Setting up the monitor 5 ..............
2.1 Installation ......................................5
2.2 Operating the monitor 6 ................
2.3 Remove the Base Assembly for
VESA Mounting 10 ..........................
3. Image Optimization 11 .................
3.1 SmartImage ................................. 11
3.2 SmartContrast ............................. 12
4. Adaptive Sync 13 ............................
5. TechnicalSpecications ...........14
5.1 Resolution & Preset Modes 17 .....
6. Power Management 18 ................
7. Customercareandwarranty..19
7.1 Philips’ Flat Panel Monitors Pixel
Defect Policy 19 ................................
7.2 Customer Care & Warranty 22 .....
8. Troubleshooting&FAQs .........23
8.1 Troubleshooting ......................... 23
8.2 General FAQs 24 ...............................
1
1. Important
This electronic user’s guide is intended
for anyone who uses the Philips monitor.
Take time to read this user manual
before you use your monitor. It contains
important information and notes
regarding operating your monitor.
The Philips guarantee applies provided
the product is handled properly for
its intended use, in accordance with
its operating instructions and upon
presentation of the original invoice
or cash receipt, indicating the date of
purchase, dealer’s name and model and
production number of the product.
1.1 Safety precautions and
maintenance
Warnings
Use of controls, adjustments or
procedures other than those specied
in this documentation may result in
exposure to shock, electrical hazards
and/or mechanical hazards.
Read and follow these instructions when
connecting and using your computer
monitor.
Excessive sound pressure from earphones
and headphones can cause hearing
loss. Adjustment of the equalizer to
maximum increases the earphones
and headphones output voltage and
therefore the sound pressure level.
Operation
• Please Keep the monitor out of
direct sunlight, very strong bright
lights and away from any other heat
source. Lengthy exposure to this
type of environment may result in
discoloration and damage to the
monitor.
• Keep the display away from oil. Oil
may damage the plastic cover of the
display and void the warranty.
• Remove any object that could fall
into ventilation holes or prevent
proper cooling of the monitor’s
electronics.
• Do not block the ventilation holes
on the cabinet.
• When positioning the monitor, make
sure the power plug and outlet are
easily accessible.
• If turning off the monitor by
detaching the power cable or DC
power cord, wait for 6 seconds
before attaching the power cable or
DC power cord for normal operation.
• Please use approved power cord
provided by Philips all the time. If
your power cord is missing, please
contact with your local service
center. (Please refer to Service
contact information listed in
Important information manual.)
• Operate under the specified power
supply. Be sure to operate the
monitor only with the specified
power supply. Use of an incorrect
voltage will cause malfunction and
may cause fire or electric shock.
• Protect the cable. Do not pull or
bend the power cable and signal
cable. Do not place the monitor
or any other heavy objects on the
cables, if damaged, the cables may
cause fire or electric shock.
• Do not subject the monitor to severe
vibration or high impact conditions
during operation.
• To avoid potential damage, for
example the panel peeling from the
bezel, ensure that the monitor does
not tilt downward by more than -5
degrees. If the -5 degree downward
tilt angle maximum is exceeded, the
2
monitor damage will not be covered
under warranty.
• Do not knock or drop the monitor
during operation or transportation.
• Excessive usage of monitor can cause
eye discomfort, it’s better to take
shorter breaks more often at your
workstation than longer breaks
and less often; for example a 5-10
minute break after 50-60-minute
continuous screen use is likely to
be better than a 15-minute break
every two hours. Try to keep your
eyes from eye strain while using the
screen for a constant period of time
by :
• Looking at something varying
distances after a long period
focusing on the screen.
• Conscious Blinking often while
you work.
• Gently closing and rolling your
eyes to relax.
• Reposition your screen to appro-
priate height and angle accord-
ing to your height.
• Adjusting the brightness and
contrast to appropriate level.
• Adjusting the environment light-
ing similar to that of your screen
brightness, avoid the uorescent
lighting, and surfaces that don’t
reect too much light.
• Seeing a doctor if your symp-
toms.
Maintenance
• To protect your monitor from
possible damage, do not put
excessive pressure on the LCD panel.
When moving your monitor, grasp
the frame to lift; do not lift the
monitor by placing your hand or
fingers on the LCD panel.
• Oil-based cleaning solutions may
damage the plastic parts and void
the warranty.
• Unplug the monitor if you are not
going to use it for an extensive
period of time.
• Unplug the monitor if you need to
clean it with a slightly damp cloth.
The screen may be wiped with a
dry cloth when the power is off.
However, never use organic solvent,
such as, alcohol, or ammonia-based
liquids to clean your monitor.
• To avoid the risk of shock or
permanent damage to the set, do
not expose the monitor to dust,
rain, water, or excessive moisture
environment.
• If your monitor gets wet, wipe it
with dry cloth as soon as possible.
• If foreign substance or water gets in
your monitor, please turn the power
off immediately and disconnect
the power cord. Then, remove the
foreign substance or water, and send
it to the maintenance center.
• Do not store or use the monitor in
locations exposed to heat, direct
sunlight or extreme cold.
• In order to maintain the best
performance of your monitor and
use it for a longer lifetime, please
use the monitor in a location
that falls within the following
temperature and humidity ranges.
• Temperature: 0-40°C 32-104°F
• Humidity: 20-80% RH
Important information for Burn-in/
Ghost image
• Always activate a moving screen
saver program when you leave
your monitor unattended. Always
activate a periodic screen refresh
application if your monitor will
display unchanging static content.
3
Uninterrupted display of still or
static images over an extended
period may cause “burn-in”, also
known as “after-imaging” or “ghost
imaging”, on your screen.
• “Burn-in”, “after-imaging”, or
“ghost imaging” is a well-known
phenomenon in LCD panel
technology. In most cases, the “burn-
in” or “after-imaging” or “ghost
imaging” will disappear gradually
over a period of time after the
power has been switched off.
Warning
Failure to activate a screen saver, or
a periodic screen refresh application
may result in severe “burn-in” or “after-
image” or “ghost image” symptoms
that will not disappear and cannot be
repaired. The damage mentioned above
is not covered under your warranty.
Service
• The casing cover should be opened
only by qualified service personnel.
• If there is any need for any
document for repair or integration,
please contact with your local
service center. (Please refer to
Service contact information listed in
Important information manual.)
• For transportation information,
please refer to “Technical
Specifications”.
• Do not leave your monitor in a car/
trunk under direct sun light.
Note
Consult a service technician if the
monitor does not operate normally, or
you are not sure what procedure to take
when the operating instructions given in
this manual have been followed.
1.2 Notational Descriptions
The following subsections describe
notational conventions used in this
document.
Notes, Cautions and Warnings
Throughout this guide, blocks of text
may be accompanied by an icon and
printed in bold or italic type. These blocks
contain notes, cautions or warnings.
They are used as follows:
Note
This icon indicates important
information and tips that help you make
better use of your computer system.
Caution
This icon indicates information that
tells you how to avoid either potential
damage to hardware or loss of data.
Warning
This icon indicates the potential for
bodily harm and tells you how to avoid
the problem.
Some warnings may appear in alternate
formats and may not be accompanied
by an icon. In such cases, the specic
presentation of the warning is
mandated by the relevant regulatory
authority.
4
1.3 Disposal of product and
packing material
Waste Electrical and Electronic
Equipment-WEEE
This marking on the product or on
its packaging illustrates that, under
European Directive 2012/19/EU
governing used electrical and electronic
appliances, this product may not be
disposed of with normal household
waste. You are responsible for disposal
of this equipment through a designated
waste electrical and electronic
equipment collection. To determine the
locations for dropping o such waste
electrical and electronic, contact your
local government oce, the waste
disposal organization that serves your
household or the store at which you
purchased the product.
Your new monitor contains materials
that can be recycled and reused.
Specialized companies can recycle your
product to increase the amount of
reusable materials and to minimize the
amount to be disposed of.
All redundant packing material has
been omitted. We have done our utmost
to make the packaging easily separable
into mono materials.
Please nd out about the local
regulations on how to dispose of your
old monitor and packing from your sales
representative.
Taking back/Recycling Information for
Customers
Philips establishes technically and
economically viable objectives
to optimize the environmental
performance of the organization's
product, service and activities.
From the planning, design and
production stages, Philips emphasizes
the important of making products
that can easily be recycled. At Philips,
end-of-life management primarily
entails participation in national take-
back initiatives and recycling programs
whenever possible, preferably in
cooperation with competitors,
which recycle all materials (products
and related packaging material) in
accordance with all Environmental
Laws and taking back program with the
contractor company.
Your display is manufactured with high
quality materials and components which
can be recycled and reused.
To learn more about our recycling
program please visit
http://www.philips.com/a-w/about/
sustainability.html
5
2. Setting up the
monitor
2.1 Installation
1 Package contents
*DP *HDMI
*USB C-C/A
*USB C-C
*USB C-A
Power
5000 S eries
Monitor
Q rtuick sta
Regis ter y r r ge aou p oduct and t s upport t www lips.c /welcome.phi om
N5600AE
N5600E
*Dierent according to region
2 Install the base
1. Place the monitor face down on a
smooth surface. Pay attention not to
scratch or damage the screen.
2. .Hold the stand with both hands
(1) Gently attach the base to the
stand.
(2) Use your ngers to tighten the
screw located at the bottom of
the base.
(3) Use a screwdriver to tighten the
screw located at the bottom of
the base, and secure the base to
the stand tightly.
(4) Gently attach the stand to the
VESA mount area until the latch
locks the stand.
1
2
3
4
Caution
Place the monitor face down on a
smooth surface. Pay attention not to
scratch or damage the screen.
6
3 Connecting to your PC
12 3 4 5
6
1 AC power input
2 HDMI input
3 DisplayPort input
4 USB-C
5 Audio Out
6 Kensington anti-theft lock
Connect to PC
1. Connect the power cord to the back
of the monitor rmly.
2. Turn o your computer and unplug
its power cable.
3. Connect the monitor signal cable to
the video connector on the back of
your computer.
4. Plug the power cord of your
computer and your monitor into a
nearby outlet.
5. Turn on your computer and monitor.
If the monitor displays an image,
installation is complete.
2.2 Operating the monitor
1 Description of the control buttons
Press to switch power on.
Press more than 3 seconds to
switch power o.
Access the OSD menu
.
Conrm the OSD adjustment.
Adjust the Brightness
Adjust the OSD menu.
Change the signal input
source.
Adjust the OSD menu.
SmartImage Game menu.
There are multiple selections:
FPS, Racing, RTS, Gamer 1,
Gamer 2, LowBlue Mode,
EasyRead and O.
Return to previous OSD level.
7
2 Description of the On Screen Display
What is On-Screen Display (OSD)?
On-Screen Display (OSD) is a feature in
all Philips LCD monitors. It allows an end
user to adjust screen performance or
select functions of the monitors directly
through an on-screen instruction
window. A user friendly on screen
display interface is shown as below:
 


 


 


 

 

Basic and simple instruction on the
control keys
To access the OSD menu on this Philips
display simply use the single toggle
button on the rear side of the display.
The single button operates like a
joystick. To move the cursor, simply
toggle the button in four directions.
Press the button to select desired option.
The OSD Menu
Below is an overall view of the structure
of the On-Screen Display. You can use
this as a reference when you want to
work your way around the dierent
adjustments later on.
Main menu Sub menu
Picture
OSD Setting
Setup
Language
Color
Input
Audio
LowBlue
Mode
Horizontal
Vertical
Transparency
OSD Time Out
English, Deutsch, Español, , Français, Italiano, MagyarΕλληνική ，
Nederlands, Português, Português do Brasil Polski ,， ，Русский
Svenska Suomi Türkçe Čeština , ， ， ， ，Українська 简体中文,
繁體中文，日本語，
Color Temperature
sRGB
User Dene
HDMI 1.4
DisplayPort
Sharpness
SmartContrast
Brightness
Contrast
Picture Format
SmartImage
Mute
Gamma
Pixel Orbiting
USB C
On
O
0 100~
0 100~
O, 1, 2, 3, 4
5s, 10s, 20s, 30s, 60s
Native, 5000K, 6500K, 7500K,
8200K, 9300K, 11500K
Red: 0 100~
Green: 0 100~
Blue: 0 100~
0 100~
0 100~
0 100~
On, O
0 100~
Wide screen, 4:3
FPS, Racing, RTS, Gamer1, Gamer2,
LowBlue Mode, EasyRead, O
On, O
Over Scan On, O
1.8, 2.0, 2.2, 2.4, 2.6
Information
On, O
On, O
Resolution
Notication
USB Setting USB Standby
Mode
Reset Yes, No
Volume
On, O
1, 2, 3, 4
Game Setting
SmartResponse
SmartFrame
MPRT Level
MPRT
O, Fast , Faster, Fastest
0 20~
On, O
Adaptive Sync On, O
On, O
Size (1, 2, 3, 4, 5, 6, 7)
Brightness (0 100)~
Contrast(0 100)~
H. position
V. position
8
Note
• MPRT: To reduce motion blur, LED
backlight will strobe synchronously
with screen refresh, which may
cause noticeable brightness change.
• 75Hz refresh rate or higher is re-
quired for MPRT.
• Adaptive Sync and MPRT cannot be
enabled simultaneously.
• MPRT is to adjust brightness for blur
reduction, so cannot adjust bright-
ness while MPRT is turned on.
• MPRT is gaming-optimized mode.
Turn on MPRT may cause noticeable
screen ickering. It is recommended
to turn o when you are not using
the gaming function.
3 Resolution notication
This monitor is designed for optimal
performance at its native resolution,
2560 x 1440. When the monitor is
powered on at a dierent resolution, an
alert is displayed on screen: Use 2560 x
1440 for best results.
Display of the native resolution alert can
be switched o from Setup in the OSD
(On Screen Display) menu.
4 Physical Function
Tilt
20°
-5°
Height adjustment
130mm
9
Pivot
90°-90°
0°0°
Warning
• To avoid potential screen damage,
such as panel peeling, ensure that
the monitor does not tilt downward
by more than -5 degrees.
• Do not press the screen while
adjusting the angle of the monitor.
Grasp only the bezel.
10
2.3 Remove the Base Assembly
for VESA Mounting
Before you start disassembling the
monitor base, please follow the
instructions below to avoid any possible
damage or injury.
1. Place the monitor face down on a
smooth surface. Pay attention not to
scratch or damage the screen. Then
lift the monitor stand.
2. While keeping the release button
pressed, tilt the base and slide it out.
Note
This monitor accepts a 100mm x 100mm
VESA-Compliant mounting interface.
VESA Mounting Screw M4. Always
contact manufacturer for wall-mount
installation.
100mm
100mm
0° 90°
* Display design may dier from those
illustrated.
Warning
• To avoid potential screen damage,
such as panel peeling, ensure that
the monitor does not tilt downward
by more than -5 degrees.
• Do not press the screen while
adjusting the angle of the monitor.
Grasp only the bezel.
11
3. Image Optimization
3.1 SmartImage
1 What is it?
SmartImage provides presets that
optimize display for dierent types
of content, dynamically adjusting
brightness, contrast, color and sharpness
in real time. Whether you're working
with text applications, displaying images
or watching a video, Philips SmartImage
delivers great optimized monitor
performance.
2 Why do I need it?
You want a monitor that delivers
optimized display all your favorite
types of content, SmartImage software
dynamically adjust brightness, contrast,
color and sharpness in real time
to enhance your monitor viewing
experience.
3 How does it work?
SmartImage is an exclusive, leading edge
Philips technology that analyzes the
content displayed on your screen. Based
on a scenario you select, SmartImage
dynamically enhances the contrast, color
saturation and sharpness of images to
enhance the contents being displayed -
all in real time with the press of a single
button.
4 How to enable SmartImage?
1. Toggle to the left to launch the
SmartImage on screen display.
2. Toggle to the up or down to select
between the smartImage modes.
3. The SmartImage on screen display
will remain on screen for 5 seconds,
or you can also toggle to the left to
make conrmation.
There are multiple selections: FPS,
Racing, RTS, Gamer 1, Gamer 2, LowBlue
Mode, EasyRead and O.







 


• FPS:For playing FPS (First Person
Shooters) games. Improves dark
theme black level details.
• Racing:For playing Racing games.
Provides fastest response time and
high color saturation.
• RTS:For playing RTS (Real Time
Strategy) games, a user-selected
portion can be highlighted for RTS
12
games (through SmartFrame). The
picture quality can be adjusted for
the highlighted portion.
• Gamer1:User’s preference settings
saved as Gamer 1.
• Gamer2:User’s preference settings
saved as Gamer 2.
• LowBlueMode: LowBlue Mode for
easy on-the-eyes productivity Studies
have shown that just as ultra-
violet rays can cause eye damage,
shortwave length blue light rays
from LED displays can cause eye
damage and affect vision over time.
Developed for wellbeing, Philips
LowBlue Mode setting uses a smart
software technology to reduce
harmful shortwave blue light.
• EasyRead:Helps improve reading
of text based application like PDF
ebooks. By using a special algorithm
which increases the contrast and
boundary sharpness of text content,
the display is optimized for a
stress-free reading by adjusting
the brightness, contrast and color
temperature of the monitor.
• Off:No optimization by
SmartImageGAME.
3.2 SmartContrast
1 What is it?
Unique technology that dynamically
analyzes displayed content and
automatically optimizes a Monitor's
contrast ratio for maximum visual
clarity and viewing enjoyment, stepping
up backlighting for clearer, crisper
and brighter images or dimming
backlighting for clear display of images
on dark backgrounds.
2 Why do I need it?
You want the very best visual clarity
and viewing comfort for every type of
content. SmartContrast dynamically
controls contrast and adjusts
backlighting for clear, crisp, bright
gaming and video images or displays
clear, readable text for oce work.
By reducing your monitor's power
consumption, you save on energy costs
and extend the lifetime of your monitor.
3 How does it work?
When you activate SmartContrast, it will
analyse the content you are displaying
in real time to adjust colors and control
backlight intensity. This function will
dynamically enhance contrast for a great
entertainment experience when viewing
videos or playing games.
13
4. Adaptive Sync
Adaptive Sync
PC gaming has long been an imperfect
experience because GPUs and monitors
update at dierent rates. Sometimes
a GPU can render many new pictures
during a single update of the monitor,
and the monitor will show pieces of each
picture as a single image. This is called
“tearing.” Gamers can x tearing with
a feature called “v-sync,” but the image
can become jerky as the GPU waits on
the monitor to call for an update before
delivering new pictures.
The responsiveness of mouse input and
overall frames per second are reduced
with v-sync, too. AMD Adaptive Sync
technology eliminates all of these
problems by letting the GPU update the
monitor the moment a new picture is
ready, leaving gamers with unbelievably
smooth, responsive, tearing-free games.
Followed by the graphic card that are
compatible.
■Operating system
• Windows 10/8.1/8/7
■Graphic Card: R9 290/300 Series &
R7 260 Series
• AMD Radeon R9 300 Series
• AMD Radeon R9 Fury X
• AMD Radeon R9 360
• AMD Radeon R7 360
• AMD Radeon R9 295X2
• AMD Radeon R9 290X
• AMD Radeon R9 290
• AMD Radeon R9 285
• AMD Radeon R7 260X
• AMD Radeon R7 260
■Processor A-Series Desktop and
Mobility APUs
• AMD A10-7890K
• AMD A10-7870K
• AMD A10-7850K
• AMD A10-7800
• AMD A10-7700K
• AMD A8-7670K
• AMD A8-7650K
• AMD A8-7600
• AMD A6-7400K
14
5. TechnicalSpecifications
Picture/Display
Monitor Panel Type IPS Technology
Backlight W-LED
Panel Size 27" W (68.6 cm)
Aspect Ratio 16:9
Pixel Pitch 0.2331 (H) mm x 0.2331 (V) mm
Contrast Ratio(typ.) 1000:1
Optimum Resolution 2560 x 1440 @ 60 Hz
Viewing Angle 178° (H) / 178° (V) @ C/R > 10 (typ.)
Monitor Colors 16.7M
Flicker Free Yes
Picture Enhancement SmartImage Game
Vertical Refresh Rate 48 Hz - 75 Hz
Horizontal Frequency 30 KHz - 114 KHz
sRGB YES
LowBlue Mode YES
EasyRead YES
Adaptive Sync YES
Connectivity
Signal Input source HDMI, DisplayPort, USB-C (DisplayPort Alt mode)
Connectors
1 x HDMI 1.4 (HDCP 1.4)
1 x DisplayPort 1.2 (HDCP 1.4)
1 x Audio out
1 x USB C (upstream)
Sync input Separate Sync
USB
USB Ports USB C p16-x1 (upstream, DisplayPort Alt mode, HDCP 1.4)
Power Delivery
USB C:
USB PD version 3.0, up to 65W (5V/3A, 9V/3A, 10V/3A,
12V/3A, 15V/3A, 20V/3.25A)
Super Speed USB C/USB A: USB 3.2 Gen1, 5 Gbps
Convenience
OSD Languages
English, German, Spanish, Greek, French, Italian, Hungarian,
Dutch, Portuguese, Brazil Portuguese, Polish, Russian,
Swedish, Finnish, Turkish, Czech, Ukranian, Simplied
Chinese, Traditional Chinese, Japanese, Korean
Other Convenience VESA mount (100 x 100 mm), Kensington Lock
Plug & Play
Compatibility DDC/CI, sRGB, Windows 10/8.1/8/7, Mac OS X
15
Stand
Tilt -5 / +20 degree
Height adjustment 130 mm
Pivot -90 / +90 degree
Power
Consumption
AC Input Voltage
at 100VAC ,
60Hz
AC Input Voltage
at 115VAC ,
60Hz
AC Input Voltage
at 230VAC, 50Hz
Normal Operation 30.2 W (typ.) 30.2 W (typ.) 29.2 W (typ.)
Sleep (Standby mode) 0.5 W 0.5 W 0.5 W
O mode 0.3 W 0.3 W 0.3 W
Heat Dissipation*
AC Input Voltage
at 100VAC ,
60Hz
AC Input Voltage
at 115VAC ,
60Hz
AC Input Voltage
at 230VAC ,
50Hz
Normal Operation 103.07 BTU/hr
(typ.)
103.07 BTU/hr
(typ.)
102.05 BTU/hr
(typ.)
Sleep (Standby mode) 1.71 BTU/hr 1.71 BTU/hr 1.71 BTU/hr
O mode 1.02 BTU/hr 1.02 BTU/hr 1.02 BTU/hr
Power LED indicator On mode: White, Standby/Sleep mode: White (blinking)
Power Supply Built-in, 100-240VAC, 50/60Hz
Dimensions
Product with stand (WxHxD) 614 x 510 x 212 mm
Product without stand
(WxHxD) 614 x 365 x 52 mm
Product with packaging
(WxHxD) 780 x 525 x 186 mm
Weight
Product with stand 6.52 kg
Product without stand 4.62 kg
Product with packaging 10.60 kg
Operating Condition
Temperature range
(operation) 0°C to 40°C
Relative humidity
(operation) 20% to 80%
Atmospheric pressure
(operation) 700 to 1060hPa
Temperature range
(Non-operation) -20°C to 60°C
Relative humidity
(Non-operation) 10% to 90%
Atmospheric pressure
(Non-operation) 500 to 1060hPa
16
Environmental and energy
ROHS YES
Packaging 100% recyclable
Specic Substances 100% PVC BFR free housing
Cabinet
Color Black
Finish Texture
Note
This data is subject to change without notice. Go to www.philips.com/support to
download the latest version of leaet.
17
5.1 Resolution & Preset Modes
1 Maximum Resolution
2560 x 1440 @ 75 Hz
2 Recommended Resolution
2560 x 1440 @ 60 Hz
H. freq
(kHz)
Resolution V. freq (Hz)
31.47 720 x 400 70.09
31.47 640 x 480 59.94
35.00 640 x 480 66.67
37.86 640 x 480 72.81
37.50 640 x 480 75.00
35.16 800 x 600 56.25
37.88 800 x 600 60.32
46.88 800 x 600 75.00
48.08 800 x 600 72.19
47.73 832 x 624 74.55
48.36 1024 x 768 60.00
56.48 1024 x 768 70.07
60.02 1024 x 768 75.03
44.77 1280 x 720 59.86
60 1280 x 960 60
63.89 1280 x 1024 60.02
79.98 1280 x 1024 75.03
55.94 1440 x 900 59.89
65.29 1680 x 1050 59.95
67.50 1920 x 1080 60.00
88.79 59.952560 x 1440
111.03 2560 x 1440 74.97
Note
Please notice that your display works
best at native resolution of 2560 x 1440.
For best output performance, please
always ensure that your graphic card
is capable of achieving the maximum
resolution and refresh rate of this Philips
display.
18
6. Power Management
If you have VESA DPM compliance display
card or software installed in your PC, the
monitor can automatically reduce its
power consumption when not in use. If
an input from a keyboard, mouse or other
input device is detected, the monitor will
'wake up' automatically. The following
table shows the power consumption and
signaling of this automatic power saving
feature:
Power Management Denition
VESA Mode Video H-sync V-sync Power
Used
LED
Color
Active ON Yes Yes
30.2 W
(typ.)
118.6 W
(max.)
White
Sleep
(Standby
mode)
OFF No No 0.5 W White
(blink)
O mode OFF - - 0.3 W OFF
The following setup is used to measure
power consumption on this monitor.
• Native resolution: 2560 x 1440
• Contrast: 50%
• Brightness: 80%
• Color temperature: 6500k with full
white pattern
Note
This data is subject to change without
notice.
19
7. Customercareand
warranty
7.1 Philips’ Flat Panel Monitors
Pixel Defect Policy
Philips strives to deliver the highest
quality products. We use some of the
industry's most advanced manufacturing
processes and practice stringent quality
control. However, pixel or sub pixel
defects on the TFT Monitor panels used
in at panel monitors are sometimes
unavoidable. No manufacturer can
guarantee that all panels will be
free from pixel defects, but Philips
guarantees that any monitor with an
unacceptable number of defects will be
repaired or replaced under warranty.
This notice explains the dierent types
of pixel defects and denes acceptable
defect levels for each type. In order to
qualify for repair or replacement under
warranty, the number of pixel defects
on a TFT Monitor panel must exceed
these acceptable levels. For example,
no more than 0.0004% of the sub
pixels on a monitor may be defective.
Furthermore, Philips sets even higher
quality standards for certain types or
combinations of pixel defects that are
more noticeable than others. This policy
is valid worldwide.
Sub pixels
Pixels
Pixels and Sub pixels
A pixel, or picture element, is composed
of three sub pixels in the primary colors
of red, green and blue. Many pixels
together form an image. When all sub
pixels of a pixel are lit, the three colored
sub pixels together appear as a single
white pixel. When all are dark, the three
colored sub pixels together appear as a
single black pixel. Other combinations of
lit and dark sub pixels appear as single
pixels of other colors.
Types of Pixel Defects
Pixel and sub pixel defects appear on the
screen in dierent ways. There are two
categories of pixel defects and several
types of sub pixel defects within each
category.
Bright Dot Defects
Bright dot defects appear as pixels or
sub pixels that are always lit or 'on'. That
is, a bright dot is a sub-pixel that stands
out on the screen when the monitor
displays a dark pattern. There are the
types of bright dot defects.
One lit red, green or blue sub pixel.
Two adjacent lit sub pixels:
- Red + Blue = Purple
- Red + Green = Yellow
- Green + Blue = Cyan (Light Blue)

Termékspecifikációk

Márka: Philips
Kategória: Monitor
Modell: 27E1N5600E

Szüksége van segítségre?

Ha segítségre van szüksége Philips 27E1N5600E, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Monitor Philips

Philips

Philips 221V8LB Útmutató

4 Április 2025
Philips

Philips Evnia 49M2C8900LA Útmutató

28 Március 2025
Philips

Philips 25M2N5200U Útmutató

26 Március 2025
Philips

Philips 150S3F Útmutató

24 Március 2025
Philips

Philips Brilliance B-line 241B4LPYCS Útmutató

24 Március 2025
Philips

Philips Momentum 242M7 Útmutató

20 Március 2025
Philips

Philips 27E1N1600AM Útmutató

17 Március 2025
Philips

Philips S Line 222S9 Útmutató

14 Január 2025
Philips

Philips 27B2U6903 Útmutató

3 Január 2025
Philips

Philips Envia 27M1N3500LS Útmutató

29 December 2024

Útmutatók Monitor

Legújabb útmutatók Monitor

PureTools

PureTools PT-SCREEN-100 Útmutató

2 Április 2025
Extron

Extron TLS 1025M Útmutató

2 Április 2025
Viewsonic

Viewsonic VG2752-2K Útmutató

30 Március 2025
Satco

Satco S13165 Útmutató

30 Március 2025
Satco

Satco S16434 Útmutató

30 Március 2025
Satco

Satco S23165 Útmutató

30 Március 2025
Satco

Satco S23168 Útmutató

30 Március 2025
Satco

Satco S16503 Útmutató

30 Március 2025
Satco

Satco S23167 Útmutató

30 Március 2025
Satco

Satco S13167 Útmutató

30 Március 2025