Használati útmutató Nxg Onyx NX-C8.2-ENC-X

Nxg hangszóró Onyx NX-C8.2-ENC-X

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Nxg Onyx NX-C8.2-ENC-X (2 oldal) a hangszóró kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
NX-C8.2-ENC-X 8˝ Two-Way In-Ceiling Enclosed Speaker System
Where To Place Your In-Ceiling Speakers
Placement can make all the difference in how your speakers sound, and how easy they will be to
install. Carefully consider where your speakers should be positioned. For optimum performance,
speakers should be mounted to the left and right of the main listening area and a minimum of 8
to 10 feet apart (See Fig. 2). Avoid mounting speakers in stud cavities containing electrical wiring,
heating ducts, water pipes, etc. Make sure the ceiling materials are sturdy enough to support the
weight of the speakers.
Adjustable Tweeters (Fig. 3)
The tweeter in your NXG speaker may be adjusted, allowing you to tailor the speaker to better fit
the listening area. The overall smoothest response is achieved with the tweeter facing straight out:
however, you may find the sound more pleasing by aiming tweeters toward a particular listening
area. To adjust the tweeter, grasp the outside of the tweeter plate and gently pivot it toward the
listening area.
Speaker Installation In Existing Construction (See Fig. 4 on reverse)
Once you have selected the location for your speakers, you are ready to install them.
You will need the following:
• Stud Finder • Drill & Drill Bits • Wire Cutter/Strippers • Speaker Wire
• Pencil • Masking Tape Phillips Screwdriver • Utility Knife or Drywall Saw •
NXG recommends the use of 16-gauge wire minimum. For wire options consult your retailer or
custom audio contractor.
1. NXG Architectural Speakers are designed to be installed in the ceiling or wall area between studs.
Using a stud finder, make sure you are between two studs. Tape the supplied template to the wall
and lightly trace around the inside with a pencil.
2. Cut the hole using your drywall saw. You may want to start with a small hole in the center of the
outline. This will allow you to check for any obstructions that may exist behind the desired location.
CAUTION: Be certain electrical wiring, water pipes or heating ducts do not interfere in the planned
installation areas prior to drilling or cutting the wall.
3. Run speaker wire from your amplifier or speaker switching device to the speaker location.
4. Carefully remove the grille and inner grille backing. (Note: The open cell foam inner grille backing
is designed to hide speaker components from view and may be removed if desired.) If you like the
standard white finish of your NXG speakers, skip to step 5, but if if you want your speakers to blend
in with a colored wall or ceiling, now is the time to paint your speaker’s outer frame and perforated
grille. (Remove the foam inner grille backing and put it aside in a clean and dust free area for later
reinstallation if desired.) The speaker’s outer surface will accept ordinary latex wall paint or aerosol
spray paint. Because the speaker baffle surface behind the grille should remain unpainted, you will
need to cover this area with the supplied cardboard paint mask. Cover the speaker’s interior black
surface, woofer and tweeter. Paint the outer speaker frame and grille separately. (Grille painting hint:
Use a paint roller that is nearly out of paint to first paint the inside of the grille, then the outside. This
will avoid paint filling the grille perforations.)
Congratulations on choosing NXG In-Ceiling
Loudspeakers. Like all NXG products, great
care has been taken in their design. Their
combination of advanced engineering and
state-of-the-art materials will provide you with
years of listening pleasure, while blending
smoothly into your home’s decor. Before you
get started, it is a good idea to identify all the
parts and hardware (See Fig. 1).
FIG. 1
FIG. 2
NXG ceiling speakers can be used as rear
surround channels by mounting them
(1) on each side of, (2) just behind, or
(3) in back of the viewing position.
1
1
2
2
3
3
FIG. 3
OWNER’S MANUAL
(Continued on reverse)
Speaker with self-contained
mounting clamps
Metal grille with foam
inner grille cover
Black
grille
adhesive
Cutout
template
Painting mask
Pivoting
tweeter
Grille
removal
tool
Warranty Service
Warranty service must be performed by an authorized service center, usually a NXG speaker
systems dealer or its authorized agent. You may obtain a list
of authorized service centers by contacting NXG. All war-
ranty repairs must be accompanied by the original bill of
sales. No other document is acceptable or is required. This
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
NXG reserves the right to revise speaker system specifications
without notice.
NXG Speakers Three-Year Limited Warranty
If the NXG speaker system proves to be defective in workmanship or materials within three
years from the date of the original customer’s purchase, we will, at our option, repair or
replace the defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability and fitness for a particular
purpose, are limited in duration to the length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or replacement of the product at
our option.NXG shall not be liable for incidental or consequential damages of any kind or
character because of product defects. Some states do not allow limitations on how long an
implied warranty lasts and/or do not allow the exclusion or limitation of incidental or conse-
quential damages, so the above limitations and exclusions may not apply.
5. Attach the wire to the input terminals on the rear of the
speaker. Remember to maintain proper polarity with the
amplifier by attaching the positive (+) lead to the red ter-
minal and the negative (-) lead to the black terminal.
6. See Fig. 5. With the speaker wire attached to the
speaker, slide the speaker up inside the cut-out hole.
Center the speaker in the cut-out hole and turn the four
locking screws clockwise until the speaker is drawn up
snugly to the wall board from behind, clamping the speak-
er in place. Try to tighten each screw equally. Replace the
speaker grill by gently pressing it into place. If necessary,
use black grille adhesive to secure the grille.
New Construction
1. Determine speaker locations and mark them on your
plans for future reference.
2. If possible, run speaker wires after HVACand electrical
wiring is in place.
3. Secure speaker wires in place along the run with insu-
lated staples only and be careful not to pierce the wire’s
insulation. Allow a bit of slack for expansion of building
materials.
4. Needless to say, the actual speakers should not be
installed until the wall board is in place. In the meantime,
leave several feet of wire coiled up and secured at the
back side of the mounting hole.
5. To complete the installation follow steps 2 through 5
above.
Operational Check
After making all connections it’s a good idea to make sure
every thing is working properly. Turn on your surround or
stereo system making sure the volume control is turned
down and that the balance control is in the center position.
Activate a musical or movie source such as FM, a CD or
DVD player. Gently turn up the volume, you should hear
sound coming from your new NXG speakers. If no sound
is heard from any or all speakers, switch off the system
immediately and check for open or loose connections,
wrong polarity or shorts, or improper source selection.
FIG. 5
16648 North 94th Street
Scottsdale, AZ 85260
1-800-733-0008
www.nxgtech.com
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or improper operation.
• Any product whose serial number has been altered, defaced, or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage must be made with the carrier.)
FIG. 4
(Continued from front)
Input
Connectors
NX-C8.2-ENC-X Specifications
Maximum Power Handling: 5 - 80 watts
Sensitivity: 90dB @ 1 watt/1 meter
Frequency Response: 55 Hz-20,000 Hz
Driver Complement:
8˝ (20 mm) mica-filled polylaminate 3 cone woofer with rubber surround
1/2˝ (13mm) zero-diffraction pivoting, liquid-cooled titanium anodized dome tweeter
Nominal Impedance: 8 ohms
Overall Dimensions: 11˝ (diameter) round x 7˝ D (279mm x 178mm)
Required Ceiling Cutout: 95/8˝ (diameter) round (244mm)

Termékspecifikációk

Márka: Nxg
Kategória: hangszóró
Modell: Onyx NX-C8.2-ENC-X

Szüksége van segítségre?

Ha segítségre van szüksége Nxg Onyx NX-C8.2-ENC-X, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hangszóró Nxg

Nxg

Nxg NX-W5.2-LCR-P Útmutató

18 Augusztus 2024
Nxg

Nxg NX-W6.2-P Útmutató

18 Augusztus 2024
Nxg

Nxg NX-C6.2-P Útmutató

17 Augusztus 2024
Nxg

Nxg Onyx NX-C8.2-ENC-X Útmutató

17 Augusztus 2024
Nxg

Nxg NX-C8.3-P Útmutató

16 Augusztus 2024
Nxg

Nxg NX-C8.2-P Útmutató

16 Augusztus 2024
Nxg

Nxg NX-AW5 Útmutató

7 Július 2024

Útmutatók hangszóró

Legújabb útmutatók hangszóró

Match

Match UP C42BMW-FRT.3 Útmutató

3 Április 2025
Turbosound

Turbosound PQ12-SB Útmutató

3 Április 2025
Trust

Trust Tytan GXT 658 Útmutató

3 Április 2025
Turbosound

Turbosound PQ15-YB Útmutató

3 Április 2025
Klipsch

Klipsch Synergy KSB-S1 Útmutató

3 Április 2025
Klipsch

Klipsch Synergy KSF-10.5 Útmutató

3 Április 2025
Klipsch

Klipsch kO-R1 Útmutató

3 Április 2025
Klipsch

Klipsch Synergy SB-1 Útmutató

3 Április 2025
Klipsch

Klipsch Reference RB-5 II Útmutató

3 Április 2025
Klipsch

Klipsch Contractor CS-800-R Útmutató

3 Április 2025