Használati útmutató NetworX NX-584 HOME AUTOMATION MODULE

NetworX Biztonság NX-584 HOME AUTOMATION MODULE

Olvassa el alább 📖 a magyar nyelvű használati útmutatót NetworX NX-584 HOME AUTOMATION MODULE (12 oldal) a Biztonság kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/12
NX-584 HOME AUTOMATION MODULE
Installation Manual
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to be
met during installation, operation, and maintenance. If further information is desired or if particular problems arise that are not
covered sufficiently for the purchaser’s purpose, the matter should be referred to GE Interlogix, Gladewater, Texas, USA.
This document contains proprietary information of GE Interlogix, USA and is furnished to its customer solely to assist that
customer in the installation, testing, operations, and/or maintenance of the equipment described. This document shall not be
reproduced in whole or in part nor shall its contents be disclosed to any third party without the written approval of GE Interlogix.
Please refer to the current GE Interlogix product catalog for detailed warranty information.
TABLE OF CONTENTS
I. GENERAL DESCRIPTION .................................................................................................2
II. TERMINALS & PIN-OUT....................................................................................................2
III. ENCLOSURE DIAGRAM....................................................................................................3
IV. WIRING DIAGRAM.............................................................................................................4
V. ENROLLING THE MODULE...............................................................................................4
VI. PROGRAMMING THE MODULE........................................................................................5
VII. PROGRAMMING DATA .....................................................................................................5
VIII. LEDS INDICATORS............................................................................................................6
IX. PROGRAMMING LOCATIONS..........................................................................................7
X. PROGRAMMING WORKSHEETS....................................................................................10
XI. SPECIFICATIONS ............................................................................................................12
© 2003 GE Interlogix
NetworX is a trademark of GE Interlogix. All rights reserved.
NX-584 Home Automation
2
I. GENERAL DESCRIPTION
The NetworX NX-584 is a low cost add-on module that fits neatly into any NetworX family system
enclosure and provides a standard RS-232 bi-directional DB-9 connector for connection to a home
automation host system. A simple three-wire connection to the main control is all that is required to
fully integrate this card into the system.
The NX-584 has several levels of security that can be programmed in at the time of installation to
allow as much or as little security system information to be passed to the host system. It can also be
set to limit the commands that will be accepted from the host system to prevent unauthorized
attempts to override the security system status.
The unit can be easily configured for communication in an ASCII or Binary protocol. A selectable
baud rate can be set from 600 baud to 76.8k baud with hardware RTS and CTS handshaking. The
ASCII implementation is easy to use and debug with standard programming tools while the Binary
version is a more efficient for method for transferring information between the two systems. The
system integrator can select any number of events or conditions to cause the NX-584 to send the
relevant information to the host without polling. This allows for a faster response to activity than
polling alone can provide.
All security system information can be requested at anytime if enabled to do so by the installer. This
is useful at system initialization and at periodic intervals to keep the two systems in sync without
worrying about missing any transitional event. This information is organized as System, Partition,
Zones and Outputs. System information will contain such information as power status, phone line
condition, module troubles, and other system wide condition. Partition information includes readiness
of all zones assigned, armed state, entry / exit delays, last user number, alarm condition and many
other conditions within a specific partition. Zone information includes faults, alarm memory, bypasses,
troubles, tampers, low batteries, missing and partition assignments. Output messages include
commands that can be passed to or from devices in X-10 compatible format.
II. TERMINALS & PIN-OUT
TERMINAL DESCRIPTIONS
POS Connect to the KP POS terminal of the NX-8
COM
Connect to the KP COM terminal of the NX-8
DATA
Connect to the KP DATA terminal of the NX-8
NX-584 Home Automation 3
DB-9 Pin-out Pin Number Signal
Name Direction
NX------PC Jumper
Number A Position B Position
Cts* → J7 8** 7
Txd → J8 2 3**
Rts* ← J9 8 7**
Rxd ← J10 2** 3
Sig.Gnd. ←→ -- 5
Unused -- -- 1,4,6,9
*Note: Rts and Cts signals are not currently supported
**Note: Default jumper settings
III. ENCLOSURE DIAGRAM
Inside the can, several 2-holed insertion points have been
constructed. This allows for either vertical or horizontal placement of
the modules. Notice that the insertion points have two sizes of
holes -- a larger hole and a smaller hole.
Diagram 1: The black plastic PCB guides are grooved on one edge
where the PC Board will be seated. The end with the half-moon
protrusion fits into the larger hole. The smaller hole is for the screw.
Diagram 2: Place the first black plastic PCB guide in the top insertion
point, grooved edge downward. The half-moon protrusion will be in
the large hole. It does not require force. Insert one of the provided
screws into the smaller hole (from inside the can) to secure it in place.
A screwdriver should reach through the notch that runs the length of
the guide to tighten the screw. The second PCB guide should be
positioned opposite of the first (grooved edge up) and placed in the
lower insertion point, using the same procedures described above.
Once mounted, screw it in securely.
Diagram 3: The PC board should slide freely in the grooves of both
guides.

Termékspecifikációk

Márka: NetworX
Kategória: Biztonság
Modell: NX-584 HOME AUTOMATION MODULE

Szüksége van segítségre?

Ha segítségre van szüksége NetworX NX-584 HOME AUTOMATION MODULE, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Biztonság NetworX

NetworX

NetworX NX-595E IP Communication Module Útmutató

5 Október 2024
NetworX

NetworX NX-408 Útmutató

20 Szeptember 2024
NetworX

NetworX NX-124E Útmutató

19 Augusztus 2024
NetworX

NetworX NX-108E Útmutató

17 Augusztus 2024
NetworX

NetworX NX-4 Útmutató

17 Augusztus 2024
NetworX

NetworX NX-448 Útmutató

7 Augusztus 2024
NetworX

NetworX NP0098.1 Útmutató

5 Augusztus 2024
NetworX

NetworX NX-10 Útmutató

5 Augusztus 2024
NetworX

NetworX NX-6V2 System Keypad Útmutató

4 Augusztus 2024
NetworX

NetworX NX-4SE Útmutató

3 Augusztus 2024

Útmutatók Biztonság

Legújabb útmutatók Biztonság

Aritech

Aritech SHATTERPRO 3 Útmutató

16 Január 2025
Axis

Axis Camera Station S9001 Mk II Desktop Terminal Útmutató

15 Január 2025
Eminent

Eminent EM6511 Útmutató

15 Január 2025
Ranex

Ranex RX2567-Z Útmutató

12 Január 2025
Technaxx

Technaxx TX-106 Útmutató

11 Január 2025
Provision-ISR

Provision-ISR NVR2-4100P Útmutató

23 Szeptember 2024
Gira

Gira 0342 Útmutató

23 Szeptember 2024
Unitron

Unitron Smart Alert Systeem Útmutató

23 Szeptember 2024
Netatmo

Netatmo Welcome Útmutató

22 Szeptember 2024
Provision-ISR

Provision-ISR I4s-371UVVF - Ultra-Vision WDR Útmutató

20 Szeptember 2024