Használati útmutató Netgear MR814v2
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Netgear MR814v2 (142 oldal) a router kategóriában. Ezt az útmutatót 11 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/142
SM-MR814NA-2
Version 4.12
April 2003
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Reference Manual for the
MR814v2 Cable/DSL
Wireless Router
ii
© 2003 by NETGEAR, Inc. All rights reserved. April 2003.
Trademarks
NETGEAR is a trademark of Netgear, Inc.
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
Other brand and product names are registered trademarks or trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
EN 55 022 Declaration of Conformance
This is to certify that the MR814v2 Cable/DSL Wireless Router is shielded against the generation of radio interference in
accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application
of EN 55 022 Class B (CISPR 22).
iii
Bestätigung des Herstellers/Importeurs
Es wird hiermit bestätigt, daß das MR814v2 Cable/DSL Wireless Router gemäß der im BMPT-AmtsblVfg 243/1991 und
Vfg 46/1992 aufgeführten Bestimmungen entstört ist. Das vorschrifts Geräte (z.B. Testsender) mäßige Betreiben einiger
kann jedoch gewissen Beschränkungen unterliegen. Lesen Sie dazu bitte die Anmerkungen in der Betriebsanleitung.
Das Bundesamt für Zulassungen in der Telekommunikation wurde davon unterrichtet, daß dieses Gerät auf den Markt
gebracht wurde und es ist berechtigt, die Serie auf die Erfüllung der Vorschriften hin zu überprüfen.
Certificate of the Manufacturer/Importer
It is hereby certified that the MR814v2 Cable/DSL Wireless Router has been suppressed in accordance with the
conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example,
test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the
notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market
and has been granted the right to test the series for compliance with the regulations.
Voluntary Control Council for Interference (VCCI) Statement
This equipment is in the second category (information equipment to be used in a residential area or an adjacent area
thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing
Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas.
When used near a radio or TV receiver, it may become the cause of radio interference.
Read instructions for correct handling.
Customer Support
Refer to the Support Information Card that shipped with your MR814v2 Cable/DSL Wireless Router.
World Wide Web
NETGEAR maintains a World Wide Web home page that you can access at the universal resource locator (URL)
http://www.netgear.com. A direct connection to the Internet and a Web browser such as Internet Explorer
or Netscape are required.
iv
Contents v
Contents
Preface
About This Manual
Chapter 1
Introduction
Key Features of the Router ............................................................................................1-1
802.11b Standards-based Wireless Networking ......................................................1-2
A Powerful, True Firewall with Content Filtering ......................................................1-2
Security ....................................................................................................................1-3
Autosensing Ethernet Connections with Auto Uplink™ ...........................................1-3
Extensive Protocol Support ......................................................................................1-3
Easy Installation and Management ..........................................................................1-4
Maintenance and Support ........................................................................................1-4
Package Contents ..........................................................................................................1-5
The Router’s Front Panel .........................................................................................1-6
The Router’s Rear Panel .........................................................................................1-7
Chapter 2
Connecting the Router to the Internet
What You Will Need Before You Begin ...........................................................................2-1
Cabling and Computer Hardware Requirements .....................................................2-1
Computer Network Configuration Requirements .....................................................2-1
Internet Configuration Requirements .......................................................................2-2
Where Do I Get the Internet Configuration Parameters? .........................................2-2
Record Your Internet Connection Information ..........................................................2-3
Connecting the MR814v2 to Your LAN ...........................................................................2-4
PPPoE Wizard-Detected Option ..............................................................................2-8
Telstra Bigpond Cable Wizard-Detected Option .......................................................2-9
Dynamic IP Wizard-Detected Option .....................................................................2-10
Fixed IP Account Wizard-Detected Option ............................................................. 2-11
Manually Configuring Your Internet Connection ...........................................................2-13
vi Contents
Chapter 3
Wireless Configuration
Considerations For A Wireless Network ......................................................................... 3-1
Observe Performance, Placement, and Range Guidelines .....................................3-1
Implement Appropriate Wireless Security ................................................................ 3-2
Understanding Wireless Settings ...................................................................................3-2
Restricting Wireless Access to Your Network ..........................................................3-3
Restricting Access to Your Network by Turning Off Wireless Connectivity ........3-4
Restricting Wireless Access Based on the Wireless Network Name (SSID) .....3-4
Restricting Wireless Access Based on the Wireless Access List ......................3-4
Choosing Authentication and Security Encryption Methods ....................................3-6
Authentication Scheme Selection ......................................................................3-6
Encryption Strength Choices .............................................................................3-6
How to Set Up and Test Basic Wireless Connectivity ..............................................3-8
How to Restrict Wireless Access by MAC Address .................................................3-9
Configure WEP ......................................................................................................3-10
Chapter 4
Content Filtering
Content Filtering Overview .............................................................................................4-1
Blocking Access to Internet Sites ...................................................................................4-2
Blocking Access to Internet Services .............................................................................4-3
Configuring a User Defined Service .........................................................................4-4
Configuring Services Blocking by IP Address Range ..............................................4-5
Scheduling When Blocking Will Be Enforced .................................................................4-5
Viewing Logs of Web Access or Attempted Web Access ...............................................4-6
Configuring E-Mail Alert and Web Access Log Notifications ..........................................4-7
Chapter 5
Maintenance
Viewing Router Status Information .................................................................................5-1
Viewing a List of Attached Devices .................................................................................5-5
Upgrading the Router Software ......................................................................................5-5
Configuration File Management .....................................................................................5-6
Restoring and Backing Up the Configuration ...........................................................5-7
Erasing the Configuration .........................................................................................5-8
Changing the Administrator Password ...........................................................................5-8
Contents vii
Chapter 6
Advanced Configuration of the Router
Configuring for Port Forwarding to Local Servers ..........................................................6-1
Adding a Custom Service .........................................................................................6-2
Editing or Deleting a Port Forwarding Entry .............................................................6-2
Local Web and FTP Server Example .......................................................................6-3
Multiple Computers for Half Life, KALI or Quake III Example ..................................6-3
Configuring the WAN Setup Options ..............................................................................6-4
Setting Up a Default DMZ Server .............................................................................6-4
Respond to Ping on Internet WAN Port ...................................................................6-5
Setting the MTU Size ...............................................................................................6-5
Using the LAN IP Setup Options ....................................................................................6-6
Configuring LAN TCP/IP Setup Parameters ............................................................6-6
Using the Router as a DHCP server ........................................................................6-7
Using Address Reservation ......................................................................................6-8
Using a Dynamic DNS Service .......................................................................................6-9
Configuring Static Routes .............................................................................................6-10
Enabling Remote Management Access .......................................................................6-12
Using Universal Plug and Play (UPnP) ........................................................................6-14
Chapter 7
Troubleshooting
Basic Functioning ...........................................................................................................7-1
Power LED Not On ...................................................................................................7-1
LEDs Never Turn Off ................................................................................................7-2
LAN or WAN Port LEDs Not On ...............................................................................7-2
Troubleshooting the Web Configuration Interface ..........................................................7-3
Troubleshooting the ISP Connection ..............................................................................7-4
Troubleshooting a TCP/IP Network Using a Ping Utility .................................................7-5
Testing the LAN Path to Your Router .......................................................................7-5
Testing the Path from Your PC to a Remote Device ................................................7-6
Restoring the Default Configuration and Password ........................................................7-7
Problems with Date and Time .........................................................................................7-7
viii Contents
Appendix A
Technical Specifications
Appendix B
Network, Routing, Firewall, and Basics
Related Publications ...................................................................................................... B-1
Basic Router Concepts .................................................................................................. B-1
What is a Router? ................................................................................................... B-2
Routing Information Protocol ................................................................................... B-2
IP Addresses and the Internet ....................................................................................... B-2
Netmask .................................................................................................................. B-4
Subnet Addressing .................................................................................................. B-5
Private IP Addresses ............................................................................................... B-7
Single IP Address Operation Using NAT ....................................................................... B-8
MAC Addresses and Address Resolution Protocol ................................................. B-9
Related Documents ................................................................................................. B-9
Domain Name Server ............................................................................................ B-10
IP Configuration by DHCP ........................................................................................... B-10
Internet Security and Firewalls .................................................................................... B-10
What is a Firewall? .................................................................................................B-11
Stateful Packet Inspection ...............................................................................B-11
Denial of Service Attack ..................................................................................B-11
Ethernet Cabling .......................................................................................................... B-12
Uplink Switches, Crossover Cables, and MDI/MDIX Switching ............................ B-12
Cable Quality ......................................................................................................... B-13
Appendix C
Preparing Your Network
Preparing Your Computers for TCP/IP Networking ....................................................... C-1
Configuring Windows 95, 98, and Me for TCP/IP Networking ....................................... C-2
Install or Verify Windows Networking Components ................................................. C-2
Enabling DHCP to Automatically Configure TCP/IP Settings in Windows 95B, 98, and Me
C-4
Selecting Windows’ Internet Access Method .......................................................... C-6
Verifying TCP/IP Properties .................................................................................... C-6
Configuring Windows NT4, 2000 or XP for IP Networking ............................................ C-7
Install or Verify Windows Networking Components ................................................. C-7
DHCP Configuration of TCP/IP in Windows XP, 2000, or NT4 ............................... C-8
Contents ix
DHCP Configuration of TCP/IP in Windows XP ..................................................... C-8
DHCP Configuration of TCP/IP in Windows 2000 ................................................ C-10
DHCP Configuration of TCP/IP in Windows NT4 .................................................. C-13
Verifying TCP/IP Properties for Windows XP, 2000, and NT4 .............................. C-15
Configuring the Macintosh for TCP/IP Networking ...................................................... C-16
MacOS 8.6 or 9.x .................................................................................................. C-16
MacOS X ............................................................................................................... C-16
Verifying TCP/IP Properties for Macintosh Computers ......................................... C-17
Verifying the Readiness of Your Internet Account ....................................................... C-18
Are Login Protocols Used? ................................................................................... C-18
What Is Your Configuration Information? .............................................................. C-18
Obtaining ISP Configuration Information for Windows Computers ....................... C-19
Obtaining ISP Configuration Information for Macintosh Computers ..................... C-20
Restarting the Network ................................................................................................ C-21
Appendix D
Wireless Networking Basics
Wireless Networking Overview ...................................................................................... D-1
Infrastructure Mode ................................................................................................. D-1
Ad Hoc Mode (Peer-to-Peer Workgroup) ................................................................ D-2
Network Name: Extended Service Set Identification (ESSID) ................................ D-2
Authentication and WEP ................................................................................................ D-3
802.11b Authentication ............................................................................................ D-3
Open System Authentication ................................................................................... D-4
Shared Key Authentication ...................................................................................... D-4
Overview of WEP Parameters ................................................................................ D-5
Key Size .................................................................................................................. D-6
WEP Configuration Options .................................................................................... D-7
Wireless Channels ......................................................................................................... D-7
Glossary
Index
x Contents
About This Manual xi
Preface
About This Manual
Congratulations on your purchase of the NETGEAR® MR814v2 Cable/DSL Wireless Router.
The MR814v2 router provides connection for multiple personal computers (PCs) to the Internet
through an external broadband access device (such as a cable modem or DSL modem) that is
normally intended for use by a single PC.
Audience
This reference manual assumes that the reader has basic to intermediate computer and Internet
skills. However, basic computer network, Internet, firewall, and VPN technologies tutorial
information is provided in the Appendices and on the Netgear website.
Typographical Conventions
This guide uses the following typographical conventions:
italics Media titles and URLs.
bold times roman User input.
courier font Screen text.
[Enter] Named keys in text are shown enclosed in square brackets. The notation [Enter] is
used for the Enter key and the Return key.
[Ctrl]+C Two or more keys that must be pressed simultaneously are shown in text linked
with a plus (+) sign.
SMALL CAPS File and directory names.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
xii About This Manual
Special Message Formats
This guide uses the following formats to highlight special messages:
Note: This format is used to highlight information of importance or special interest.
Introduction 1-1
Chapter 1
Introduction
This chapter describes the features of the NETGEAR MR814v2 Cable/DSL Wireless Router.
Key Features of the Router
The MR814v2 Cable/DSL Wireless Router with 4-port switch connects your local area network
(LAN) to the Internet through an external access device such as a cable modem or DSL modem.
The MR814v2 router provides you with multiple Web content filtering options, plus browsing
activity reporting and instant alerts -- both via e-mail. Parents and network administrators can
establish restricted access policies based on time-of-day, Website addresses and address keywords,
and share high-speed cable/DSL Internet access for up to 253 personal computers. In addition to
the Network Address Translation (NAT) feature, the built-in firewall protects you from hackers.
With minimum setup, you can install and use the router within minutes.
The MR814v2 router provides the following features:
• 802.11b Standards-based wireless networking
• Easy, web-based setup for installation and management
• Content Filtering and Site Blocking Security
• Built in 4-port 10/100 Mbps Switch
• Ethernet connection to a wide area network (WAN) device, such as a cable modem or DSL
modem
• Extensive Protocol Support
• Login capability
• Front panel LEDs for easy monitoring of status and activity
• Flash memory for firmware upgrade
Reference Manual for the MR814v2 Cable/DSL Wireless Router
1-2 Introduction
802.11b Standards-based Wireless Networking
The MR814v2 router includes an 802.11b-compliant wireless access point, providing continuous,
high-speed 11 Mbps access between your wireless and Ethernet devices. The access point
provides:
• 802.11b Standards-based wireless networking at up to 11 Mbps
• 64-bit and 128-bit WEP encryption security
• WEP keys can be generated manually or by passphrase
• Wireless access can be restricted by MAC address.
• Wireless network name broadcast can be turned off so that only devices that have the network
name (SSID) can connect.
A Powerful, True Firewall with Content Filtering
Unlike simple Internet sharing NAT routers, the MR814v2 is a true firewall, using stateful packet
inspection to defend against hacker attacks. Its firewall features include:
• Denial of Service (DoS) protection.
Automatically detects and thwarts DoS attacks such as Ping of Death, SYN Flood, LAND
Attack, and IP Spoofing.
• Blocks unwanted traffic from the Internet to your LAN.
• Blocks access from your LAN to Internet locations or services that you specify as off-limits.
• Logs security incidents.
The MR814v2 will log security events such as blocked incoming traffic, port scans, attacks,
and administrator logins. You can configure the router to email the log to you at specified
intervals. You can also configure the router to send immediate alert messages to your email
address or email pager whenever a significant event occurs.
• With its content filtering feature, the MR814v2 prevents objectionable content from reaching
your PCs. The router allows you to control access to Internet content by screening for
keywords within Web addresses. You can configure the router to log and report attempts to
access objectionable Internet sites.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
Introduction 1-3
Security
The MR814v2 router is equipped with several features designed to maintain security, as described
in this section.
• PCs Hidden by NAT
NAT opens a temporary path to the Internet for requests originating from the local network.
Requests originating from outside the LAN are discarded, preventing users outside the LAN
from finding and directly accessing the PCs on the LAN.
• Port Forwarding with NAT
Although NAT prevents Internet locations from directly accessing the PCs on the LAN, the
router allows you to direct incoming traffic to specific PCs based on the service port number
of the incoming request, or to one designated “DMZ” host computer. You can specify
forwarding of single ports or ranges of ports.
Autosensing Ethernet Connections with Auto Uplink™
With its internal 8-port 10/100 switch, the MR814v2 can connect to either a 10 Mbps standard
Ethernet network or a 100 Mbps Fast Ethernet network. Both the LAN and WAN interfaces are
autosensing and capable of full-duplex or half-duplex operation.
The router incorporates Auto UplinkTM technology. Each Ethernet port will automatically sense
whether the Ethernet cable plugged into the port should have a ‘normal’ connection such as to a
PC or an ‘uplink’ connection such as to a switch or hub. That port will then configure itself to the
correct configuration. This feature also eliminates the need to worry about crossover cables, as
Auto Uplink will accommodate either type of cable to make the right connection.
Extensive Protocol Support
The MR814v2 router supports the Transmission Control Protocol/Internet Protocol (TCP/IP) and
Routing Information Protocol (RIP). For further information about TCP/IP, refer to Appendix B,
“Network, Routing, Firewall, and Basics.”
• IP Address Sharing by NAT
The MR814v2 router allows several networked PCs to share an Internet account using only a
single IP address, which may be statically or dynamically assigned by your Internet service
provider (ISP). This technique, known as NAT, allows the use of an inexpensive single-user
ISP account.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
1-4 Introduction
• Automatic Configuration of Attached PCs by DHCP
The MR814v2 router dynamically assigns network configuration information, including
IP, gateway, and domain name server (DNS) addresses, to attached PCs on the LAN using the
Dynamic Host Configuration Protocol (DHCP). This feature greatly simplifies configuration
of PCs on your local network.
• DNS Proxy
When DHCP is enabled and no DNS addresses are specified, the router provides its own
address as a DNS server to the attached PCs. The router obtains actual DNS addresses from
the ISP during connection setup and forwards DNS requests from the LAN.
• PPP over Ethernet (PPPoE)
PPPoE is a protocol for connecting remote hosts to the Internet over a DSL connection by
simulating a dial-up connection. This feature eliminates the need to run a login program such
as Entersys or WinPOET on your PC.
Easy Installation and Management
You can install, configure, and operate the MR814v2 Cable/DSL Wireless Router within minutes
after connecting it to the network. The following features simplify installation and management
tasks:
• Browser-based management
Browser-based configuration allows you to easily configure your router from almost any type
of personal computer, such as Windows, Macintosh, or Linux. A user-friendly Setup Wizard is
provided and online help documentation is built into the browser-based Web Management
Interface.
• Smart Wizard
The MR814v2 router automatically senses the type of Internet connection, asking you only for
the information required for your type of ISP account.
• Visual monitoring
The MR814v2 router’s front panel LEDs provide an easy way to monitor its status and
activity.
Maintenance and Support
NETGEAR offers the following features to help you maximize your use of the MR814v2 router:
• Flash memory for firmware upgrade
• Free technical support seven days a week, twenty-four hours a day
Reference Manual for the MR814v2 Cable/DSL Wireless Router
Introduction 1-5
Package Contents
The product package should contain the following items:
• MR814v2 Cable/DSL Wireless Router.
• AC power adapter.
• Category 5 (CAT5) Ethernet cable.
•MR814v2 Resource CD, including:
— This guide.
— Application Notes and other helpful information.
• .
• Registration and Warranty Card.
• Support Information Card.
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the router for repair.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
1-6 Introduction
The Router’s Front Panel
The front panel of the MR814v2 router contains the status LEDs described below.
Figure 1-1: MR814v2 Front Panel
You can use some of the LEDs to verify connections. Viewed from left to right, Table 1-1
describes the LEDs on the front panel of the router. These LEDs are green when lit.
Table 1-1. LED Descriptions
Label Activity Description
Power
On
Off
Power is supplied to the router.
Power is not supplied to the router.
Internet
On
Blink
The Internet (Wide Area Network) port has detected a link with an
attached device.
Data is being transmitted or received by the Internet port.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
Introduction 1-7
The Router’s Rear Panel
The rear panel of the Model RP614 router contains the port connections listed below.
Figure 1-2: MR814v2 Rear Panel
Viewed from left to right, the rear panel contains the following features:
• AC power adapter outlet
• Four Local (LAN) Ethernet ports for connecting the router to the local PCs
• Internet (WAN) Ethernet port for connecting the router to a cable or DSL modem
• Factory Default Reset push button
• Wireless antenna
Wireless
On Indicates that the Wireless port is initialized.
Local
On (Green)
Blink (Green)
On (Amber)
Blink (Amber)
Off
The Local (LAN) port has detected link with a 100 Mbps device.
Data is being transmitted or received at 100 Mbps.
The Local port has detected link with a 10 Mbps device.
Data is being transmitted or received at 10 Mbps.
No link is detected on this port.
Table 1-1. LED Descriptions
Reference Manual for the MR814v2 Cable/DSL Wireless Router
1-8 Introduction
Connecting the Router to the Internet 2-1
Chapter 2
Connecting the Router to the Internet
This chapter describes how to set up the router on your local area network (LAN) and connect to
the Internet. You find out how to configure your MR814v2 Cable/DSL Wireless Router for
Internet access using the Setup Wizard, or how to manually configure your Internet connection.
What You Will Need Before You Begin
You need to prepare these three things before you begin:
1. Have active Internet service such as that provided by an cable or DSL broadband account.
2. Locate the Internet Service Provider (ISP) configuration information for your DSL account.
3. Connect the router to a cable or DSL modem and a computer as explained below.
Cabling and Computer Hardware Requirements
To use the MR814v2 router on your network, each computer must have an installed Ethernet
Network Interface Card (NIC) and an Ethernet cable. If the computer will connect to your network
at 100 Mbps, you must use a Category 5 (CAT5) cable such as the one provided with your router.
Computer Network Configuration Requirements
The MR814v2 includes a built-in Web Configuration Manager. To access the configuration menus
on the MR814v2, your must use a Java-enabled web browser program which supports HTTP
uploads such as Microsoft Internet Explorer or Netscape Navigator. NETGEAR recommends
using Internet Explorer or Netscape Navigator 4.0 or above. Free browser programs are readily
available for Windows, Macintosh, or UNIX/Linux.
For the initial connection to the Internet and configuration of your router, you will need to connect
a computer to the router which is set to automatically get its TCP/IP configuration from the router
via DHCP.
Note: For help with DHCP configuration, please refer to Appendix C, “Preparing Your Network”.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
2-2 Connecting the Router to the Internet
The cable or DSL modem broadband access device must provide a standard 10 Mbps (10BASE-T)
Ethernet interface.
Internet Configuration Requirements
Depending on how your ISP set up your Internet account, you will need one or more of these
configuration parameters to connect your router to the Internet:
• Host and Domain Names
• ISP Login Name and Password
• ISP Domain Name Server (DNS) Addresses
• Fixed IP Address which is also known as Static IP Address
Where Do I Get the Internet Configuration Parameters?
There are several ways you can gather the required Internet connection information.
• Your ISP provides all the information needed to connect to the Internet. If you cannot locate
this information, you can ask your ISP to provide it or you can try one of the options below.
• If you have a computer already connected using the active Internet access account, you can
gather the configuration information from that computer.
— For Windows 95/98/ME, open the Network control panel, select the TCP/IP entry for the
Ethernet adapter, and click Properties. Record all the settings for each tab page.
— For Windows 2000/XP, open the Local Area Network Connection, select the TCP/IP entry
for the Ethernet adapter, and click Properties. Record all the settings for each tab page.
— For Macintosh computers, open the TCP/IP or Network control panel. Record all the
settings for each section.
• You may also refer to the MR814v2 Resource CD for the NETGEAR Router ISP Guide which
provides Internet connection information for many ISPs.
Once you locate your Internet configuration parameters, you may want to record them on the page
below.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
Connecting the Router to the Internet 2-3
Record Your Internet Connection Information
Print this page. Fill in the configuration parameters from your Internet Service Provider (ISP).
ISP Login Name: The login name and password are case sensitive and must be entered exactly as
given by your ISP. The Service Name is not required by all ISPs. If you connect using a login
name and password, then fill in the following:
Login Name: ______________________________ Password: ____________________________
Service Name: _____________________________
Fixed or Static IP Address: If you have a static IP address, record the following information. For
example, 169.254.141.148 could be a valid IP address.
Fixed or Static Internet IP Address: ______ . ______ . ______ . ______
Gateway IP Address: ______ . ______ . ______ . ______
Subnet Mask: ______ . ______ . ______ . ______
ISP DNS Server Addresses: If you were given DNS server addresses, fill in the following:
Primary DNS Server IP Address: ______ . ______ . ______ . ______
Secondary DNS Server IP Address: ______ . ______ . ______ . ______
Host and Domain Names: Some ISPs use a specific host or domain name like CCA7324-A or
home. If you haven’t been given host or domain names, you can use the following examples as a
guide:
• If your main e-mail account with your ISP is aaa@yyy.com, then use aaa as your host name.
Your ISP might call this your account, user, host, computer, or system name.
• If your ISP’s mail server is mail.xxx.yyy.com, then use xxx.yyy.com as the domain name.
ISP Host Name: _________________________ ISP Domain Name: _______________________
For Wireless Access: For configuration of the wireless network, record the following:
Wireless Network Name (SSID): __________________
Encryption (circle one): WEP 64, WEP 128, or IPSec
WEP passphrase or key: ____________________
Reference Manual for the MR814v2 Cable/DSL Wireless Router
2-4 Connecting the Router to the Internet
Connecting the MR814v2 to Your LAN
This section provides instructions for connecting the MR814v2 router. Also, the MR814v2
Resource CD included with your router contains an animated Installation Assistant to help you
through this procedure.
Procedure: Connecting the Router
There are three steps to connecting your router:
1. Connect the router to your network
2. Log in to the router
3. Connect to the Internet
Follow the steps below to connect your router to your network. You can also refer to the Resource
CD included with your router which contains an animated Installation Assistant to help you
through this procedure.
1. Connect the router to your network.
a. Turn off your computer and Cable or DSL Modem.
b. Disconnect the Ethernet cable ( )A from your computer which connects to your cable or
DSL modem.
Figure 2-1: Disconnect the cable or DSL Modem
Cable or DSL modem
A
Reference Manual for the MR814v2 Cable/DSL Wireless Router
Connecting the Router to the Internet 2-5
c. Connect the Ethernet cable from your cable or DSL modem to the Internet port (A) on the
MR814v2.
Figure 2-2: Connect the cable or DSL Modem to the router
d. Connect the Ethernet cable which came with the router from a Local port on the router (B)
to your computer.
Figure 2-3: Connect the computers on your network to the router
Note: The MR814v2 router incorporates Auto Uplink TM technology. Each LOCAL
Ethernet port will automatically sense if the cable should have a normal connection or an
uplink connection. This feature eliminates the need to worry about crossover cables
because Auto Uplink will make the right connection either type of cable.
e. Now, turn on your computer. If software usually logs you in to your Internet connection,
do not run that software or cancel it if it starts automatically.
Cable
or DSL modem
A
Cable or
DSL modem
B
Reference Manual for the MR814v2 Cable/DSL Wireless Router
2-6 Connecting the Router to the Internet
f. Verify the following:
When your turn the router on, the power light goes on.
The router’s local lights are lit for any computers that are connected to it.
The router’s Internet light is lit, indicating a link has been established to the cable or DSL
modem.
Note: For wireless placement and range guidelines, and wireless configuration
instructions, please see Chapter 3, “Wireless Configuration.”
2. Log in to the router.
Note: To connect to the router, your computer needs to be configured to obtain an IP address
automatically via DHCP. If you need instructions on how to do this, please refer to
Appendix C, “Preparing Your Network”.
a. Connect to the router by typing http://192.168.0.1 in the address filed of Internet Explorer
or Netscape® Navigator.
Figure 2-4: Log in to the router
b. For security reasons, the router has its own user name and password. When prompted,
enter admin
for the router user name and password for the router password, both in lower
case letters.
Note: The router user name and password are not the same as any user name or password
you may use to log in to your Internet connection.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
Connecting the Router to the Internet 2-7
A login window shown below opens:
Figure 2-5: Login window
3. Connect to the Internet
Figure 2-6: Setup Wizard
a. You are now connected to the router. If you do not see the menu above, click the Setup
Wizard link on the upper left of the main menu.
b. Click Next and follow the steps in the Setup Wizard for inputting the configuration
parameters from your ISP to connect to the Internet.
Note: If you choose not to use the Setup Wizard, you can manually configure your
Internet connection settings by following the procedure “Manually Configuring Your
Internet Connection” on page 2-13.
Unless your ISP automatically assigns your configuration automatically via DHCP, you
will need the configuration parameters from your ISP as you recorded them previously in
“Record Your Internet Connection Information” on page 2-3.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
2-8 Connecting the Router to the Internet
c. When the router successfully detects an active Internet service, the router’s Internet LED
goes on. The Setup Wizard reports which connection type it discovered, and displays the
appropriate configuration menu. If the Setup Wizard finds no connection, you will be
prompted to check the physical connection between your router and the cable or DSL line.
d. The Setup Wizard will report the type of connection it finds. The options are:
• Connections which require a login using protocols such as
PPPoE, PPTP, Telstra, or Bigpond broadband connections.
• Connections which use dynamic IP address assignment.
• Connections which use fixed IP address assignment.
The procedures for filling in the configuration menu for each type of connection follow
below.
PPPoE Wizard-Detected Option
If the Setup Wizard discovers that your ISP uses PPPoE, you will see this menu:
Figure 2-7: Setup Wizard menu for PPPoE accounts
• Enter the Account Name, Domain Name, Login, and Password as provided by your ISP. These
fields are case sensitive. The router will try to discover the domain automatically if you leave
the Domain Name blank. Otherwise, you may need to enter it manually.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
Connecting the Router to the Internet 2-9
• To change the login timeout, enter a new value in minutes. This determines how long the
router keeps the Internet connection active after there is no Internet activity from the LAN.
Entering a timeout value of zero means never log out.
Note: You no longer need to run the ISP’s login program on your PC in order to access the
Internet. When you start an Internet application, your router will automatically log you in.
• If you know that your ISP does not automatically transmit DNS addresses to the router during
login, select “Use these DNS servers” and enter the IP address of your ISP’s Primary DNS
Server. If a Secondary DNS Server address is available, enter it also.
Note: If you enter DNS addresses, restart your computers so that these settings take effect.
• Click Apply to save your settings.
• Click Test to verify that your Internet connection works. If the NETGEAR website does not
appear within one minute, refer to Chapter 7, “Troubleshooting.”
Telstra Bigpond Cable Wizard-Detected Option
If the Setup Wizard discovers Telstra Bigpond Cable is your ISP, you will see this menu:
Figure 2-8: Setup Wizard menu for Telstra Bigpond Cable accounts
• Enter your Login, Password and Authentication Server. These fields are case sensitive.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
2-10 Connecting the Router to the Internet
Note: You will no longer need to launch the ISP’s login program on your PC in order to access
the Internet. When you start an Internet application, your router will automatically log you in.
• The Domain Name Server (DNS) Address parameters may be necessary to access your ISP’s
services such as mail or news servers.
Note: If you enter DNS addresses, restart your computers so that these settings take effect.
• Router MAC Address:
This section determines the Ethernet MAC address that will be used by the router on the
Internet port. Some ISPs will register the Ethernet MAC address of the network interface card
in your PC when your account is first opened. They will then only accept traffic from the
MAC address of that PC. This feature allows your router to masquerade as that PC.
To change the MAC address, select “Use this Computer’s MAC address.” The router will then
capture and use the MAC address of the PC that you are now using. You must be using the one
PC that is allowed by the ISP. Or, select “Use this MAC address” and enter it.
• Click Apply to save your settings.
• Click Test to test your Internet connection. If the NETGEAR website does not appear within
one minute, refer to Chapter 7, “Troubleshooting.
Dynamic IP Wizard-Detected Option
If the Setup Wizard discovers that your ISP uses Dynamic IP assignment, you will see this menu:
Figure 2-9: Setup Wizard menu for Dynamic IP address accounts
Reference Manual for the MR814v2 Cable/DSL Wireless Router
Connecting the Router to the Internet 2-11
• Enter your Account Name (may also be called Host Name) and Domain Name. These
parameters may be necessary to access your ISP’s services such as mail or news servers. If you
leave the Domain Name field blank, the router try to discover the domain. Otherwise, you may
need to enter it manually.
• If you know that your ISP does not automatically transmit DNS addresses to the router during
login, select Use these DNS servers and enter the IP address of your ISP’s Primary DNS
Server. If a Secondary DNS Server address is available, enter it also.
Note: If you enter DNS addresses, restart your computers so that these settings take effect.
• Click Apply to save your settings.
• Click Test to test your Internet connection. If the NETGEAR website does not appear within
one minute, refer to Chapter 7, “Troubleshooting.”
Fixed IP Account Wizard-Detected Option
If the Setup Wizard discovers that your ISP uses Fixed IP assignment, you will see this menu:
Figure 2-10: Setup Wizard menu for Fixed IP address accounts
• Fixed IP is also called Static IP. Enter your assigned IP Address, Subnet Mask, and the IP
Address of your ISP’s gateway router. This information should have been provided to you by
your ISP. You will need the configuration parameters from your ISP you recorded in “Record
Your Internet Connection Information” on page 2-3.
• Enter the IP address of your ISP’s Primary and Secondary DNS Server addresses.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
2-12 Connecting the Router to the Internet
Note: Restart the computers on your network so that these settings take effect.
• Click Apply to save the settings.
• Click Test to test your Internet connection. If the NETGEAR website does not appear within
one minute, refer to Chapter 7, “Troubleshooting.”
Reference Manual for the MR814v2 Cable/DSL Wireless Router
Connecting the Router to the Internet 2-13
Manually Configuring Your Internet Connection
You can manually configure your router using the menu below, or you can allow the Setup Wizard
to determine your configuration as described in the previous section.
Figure 2-11: Browser-based configuration Basic Settings menus
ISP Does Not Require Login ISP Does Require Login
Reference Manual for the MR814v2 Cable/DSL Wireless Router
2-14 Connecting the Router to the Internet
You can manually configure the router using the Basic Settings menu shown in Figure 2-11 using
these steps:
1. Click the Basic Settings link on the Setup menu.
2. If your Internet connection does not require a login, click No at the top of the Basic Settings
menu and fill in the settings according to the instructions below. If your Internet connection
does require a login, click Yes, and skip to step 3.
a. Enter your Account Name (may also be called Host Name) and Domain Name.
These parameters may be necessary to access your ISP’s services such as mail or news
servers.
b. Internet IP Address:
If your ISP has assigned you a permanent, fixed (static) IP address for your PC, select
“Use static IP address”. Enter the IP address that your ISP assigned. Also enter the
netmask and the Gateway IP address. The Gateway is the ISP’s router to which your router
will connect.
c. Domain Name Server (DNS) Address:
If you know that your ISP do DNS addresses to the router es not automatically transmit
during login, select “Use these DNS servers” and enter the IP address of your ISP’s
Primary DNS Server. If a Secondary DNS Server address is available, enter it also.
Note: If you enter an address here, restart the computers on your network so that these
settings take effect.
d. Gateway’s MAC Address:
This section determines the Ethernet MAC address that will be used by the router on the
Internet port. Some ISPs will register the Ethernet MAC address of the network interface
card in your PC when your account is first opened. They will then only accept traffic from
the MAC address of that PC. This feature allows your router to masquerade as that PC by
“cloning” its MAC address.
To change the MAC address, select “Use this Computer’s MAC address.” The router will
then capture and use the MAC address of the PC that you are now using. You must be
using the one PC that is allowed by the ISP. Or, select “Use this MAC address” and enter
it.
e. Click Apply to save your settings.
3. If your Internet connection does require a login, fill in the settings according to the instructions
below. Select Yes if you normally must launch a login program such as Enternet or WinPOET
in order to access the Internet.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
Connecting the Router to the Internet 2-15
Note: After you finish setting up your router, you will no longer need to launch the ISP’s login
program on your PC in order to access the Internet. When you start an Internet application,
your router will automatically log you in.
a. Select you Internet service provisory from the drop-down list.
b. The screen will change according to the ISP settings requirements of the ISP you select.
c. Fill in the parameters for your ISP according to the Wizard-detected procedures starting on
page 2-8.
d. Click Apply to save your settings.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
2-16 Connecting the Router to the Internet
Wireless Configuration 3-1
Chapter 3
Wireless Configuration
This chapter describes how to configure the wireless features of your MR814v2 router.
Considerations For A Wireless Network
In planning your wireless network, you should consider the level of security required. You should
also select the physical placement of your firewall in order to maximize the network speed. For
further information on wireless networking, refer to in Appendix D, “Wireless Networking
Basics.”
Observe Performance, Placement, and Range Guidelines
The operating distance or range of your wireless connection can vary significantly based on the
physical placement of the wireless firewall. The latency, data throughput performance, and
notebook power consumption also vary depending on your configuration choices.
For best results, place your firewall:
• Near the center of the area in which your PCs will operate.
• In an elevated location such as a high shelf where the wirelessly connected PCs have
line-of-sight access (even if through walls).
• Away from sources of interference, such as PCs, microwaves, and 2.4 GHz cordless phones.
• Away from large metal surfaces.
The time it takes to establish a wireless connection can vary depending on both your security
settings and placement. WEP connections can take slightly longer to establish. Also, WEP
encryption can consume more battery power on a notebook PC.
Note: Failure to follow these guidelines can result in significant performance
degradation or inability to wirelessly connect to the router. For complete range/
performance specifications, please see Appendix A, “Technical Specifications.”
Reference Manual for the MR814v2 Cable/DSL Wireless Router
3-2 Wireless Configuration
Implement Appropriate Wireless Security
Unlike wired network data, your wireless data transmissions can extend beyond your walls and
can be received by anyone with a compatible adapter. For this reason, use the security features of
your wireless equipment. The MR814v2 router provides highly effective security features which
are covered in detail in this chapter. Deploy the security features appropriate to your needs.
Figure 3-1: MR814v2 wireless data security options
Restricting access by MAC address filtering adds an obstacle against unwanted access to your
network, but the data broadcast over the wireless link is fully exposed. To block a determined
eavesdropper, you should use one of the data encryption options of the firewall. Wired Equivalent
Privacy (WEP) data encryption provides data security.
Understanding Wireless Settings
To configure the Wireless settings of your firewall, click the Wireless link in the main menu of the
browser interface. The Wireless Settings menu will appear.
Note: Indoors, computers can connect over 802.11b wireless networks at a
maximum range of up to 500 feet. Such distances can allow for others outside of your
immediate area to access your network.
1) Open System: Easy but no security
2) MAC Access List: No data security
3) WEP: Security but some performance impact
Wireless Data
Security Options
Range: Up to 500 Feet
MR814 v2
Reference Manual for the MR814v2 Cable/DSL Wireless Router
Wireless Configuration 3-3
Figure 3-2: Wireless Settings menu
The Wireless Network menu sections are discussed below.
• Name (SSID). The Service Set Identification is also known as the wireless network name.
Enter a value of up to 32 alphanumeric characters. In a setting where there is more than one
wireless network, different wireless network names provide a means for separating the traffic.
Any device you want to participate in this wireless network will need to use this SSID. The
MR814v2 default SSID is: NETGEAR.
• Region. This field identifies the region where the MR814v2 can be used. It may not be legal to
operate the wireless features of the router in a region other than one of those identified on this
drop-down list.
• Channel. This field determines which operating frequency will be used. It should not be
necessary to change the wireless channel unless you notice interference problems with another
nearby access point. For more information on the wireless channel frequencies please refer to
“Wireless Channels” on page D-7.
Restricting Wireless Access to Your Network
The MR814v2 Cable/DSL Wireless Router provides several ways to restrict wireless access to
your network:
• Turn off wireless connectivity completely
• Restrict access based on the Wireless Network Name (SSID)
• Restrict access based on the Wireless Card Access List
These options are discussed below.
Reference Manual for the MR814v2 Cable/DSL Wireless Router
3-4 Wireless Configuration
Figure 3-3: Wireless Access Point settings
Restricting Access to Your Network by Turning Off Wireless Connectivity
You can completely turn off the wirless portion of the MR814v2. For example, if your notebook
computer is used to wirelessly connect to your router and you take a business trip, you can turn off
the wireless portion of the router while you are travelling. Other members of your household who
use computers connected to the router via Ethernet cables will still be able to use the router.
Restricting Wireless Access Based on the Wireless Network Name (SSID)
The MR814v2 can restrict wireless access to your network by not broadcasting the wireless
network name (SSID). However, by default, this feature is turned off. If you turn this feature on,
any wireless device will not ‘see’ your MR814v2. You must configure your wireless devices to
match the wireless network name (SSID) you configure in the MR814v2 router.
Note: The SSID of any wireless access adapters must match the SSID you configure in the
MR814v2 Cable/DSL Wireless Router. If they do not match, you will not get a wireless
connection to the MR814v2.
Restricting Wireless Access Based on the Wireless Access List
This list determines which wireless hardware devices will be allowed to connect to the firewall.
1. To activate this feature, click the Setup Access List button.
Figure 3-4: Wireless Card Access List
2. Click the Turn Access Control On check box.
3. Click Add to view the Wireless Card Access Setup screen.
Termékspecifikációk
| Márka: | Netgear |
| Kategória: | router |
| Modell: | MR814v2 |
Szüksége van segítségre?
Ha segítségre van szüksége Netgear MR814v2, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók router Netgear
11 Október 2024
8 Október 2024
28 Szeptember 2024
18 Szeptember 2024
18 Szeptember 2024
18 Szeptember 2024
11 Szeptember 2024
11 Szeptember 2024
11 Szeptember 2024
8 Szeptember 2024
Útmutatók router
- router Samsung
- router Acer
- router Milwaukee
- router Bosch
- router AEG
- router StarTech.com
- router Einhell
- router Nokia
- router HP
- router Makita
- router BenQ
- router Apple
- router Ubiquiti Networks
- router Siemens
- router TP-Link
- router Medion
- router Motorola
- router Vimar
- router LogiLink
- router Alcatel
- router Roland
- router TCL
- router Digitus
- router Zebra
- router Xiaomi
- router TRENDnet
- router Mercusys
- router AVM
- router EZVIZ
- router Dell
- router Lancom
- router Strong
- router Gigabyte
- router Conceptronic
- router Thomson
- router Juniper
- router Kyocera
- router Hikvision
- router Keewifi
- router Vivanco
- router Huawei
- router Asus
- router Vtech
- router Hama
- router Zoom
- router Renkforce
- router Synology
- router Draytek
- router Iogear
- router Güde
- router Hitachi
- router Mikrotik
- router Toolcraft
- router ZyXEL
- router SPL
- router Dahua Technology
- router Smart-AVI
- router Black & Decker
- router Devolo
- router Planet
- router Tenda
- router BT
- router Black Box
- router MSI
- router Gembird
- router Cisco
- router PowerPlus
- router ATen
- router Google
- router Metabo
- router Bea-fon
- router ZTE
- router Edimax
- router Vodafone
- router ModeCom
- router HiKOKI
- router Foscam
- router Milan
- router Manhattan
- router Kogan
- router Festool
- router EnGenius
- router Sigma
- router Western Digital
- router D-Link
- router Media-Tech
- router Blustream
- router Milesight
- router Moxa
- router Sagem
- router Razer
- router Trust
- router Porter-Cable
- router Konig
- router Alfa
- router MuxLab
- router DeWalt
- router AVMATRIX
- router IFM
- router A-NeuVideo
- router Atlona
- router Schneider
- router AJA
- router Lindy
- router Cudy
- router Barco
- router QNAP
- router NEC
- router Silverline
- router Cotech
- router Siig
- router Gefen
- router Kathrein
- router Avenview
- router Lantronix
- router Technicolor
- router FSR
- router Topcom
- router Holzmann
- router Arris
- router Anker
- router I-TEC
- router Keenetic
- router Linksys
- router Teltonika
- router Sitecom
- router Intelix
- router Comprehensive
- router Ocean Matrix
- router Digitalinx
- router Alfatron
- router Belkin
- router RGBlink
- router Kopul
- router KanexPro
- router Key Digital
- router Kramer
- router BZBGear
- router UPC
- router Allnet
- router Allied Telesis
- router Airlive
- router Proximus
- router Skil
- router Eminent
- router Nilox
- router Sonos
- router Patton
- router Techly
- router Totolink
- router KPN
- router Netis
- router Envivo
- router Buffalo
- router Nest
- router LevelOne
- router ICIDU
- router Clas Ohlson
- router AT&T
- router Sweex
- router Aruba
- router Phicomm
- router Kasda
- router Jung
- router Digi
- router Verizon
- router Billion
- router T-Mobile
- router RAVPower
- router Hawking Technologies
- router Nexxt
- router Beafon
- router Kraun
- router LTS
- router Zolid
- router Sagemcom
- router Telstra
- router Eero
- router Advantech
- router Mercku
- router Hercules
- router Xantech
- router Intellinet
- router Arcadyan
- router Digiconnect
- router Ubee
- router SMC
- router Tele 2
- router Peak
- router CradlePoint
- router Davolink
- router Sixnet
- router 7inova
- router AVPro Edge
- router F-Secure
- router Rosewill
- router Digicom
- router Sabrent
- router On Networks
- router PENTAGRAM
- router Leoxsys
- router Readynet
- router OneAccess
- router Accelerated
- router Nexaira
- router Hamlet
- router Approx
- router T-com
- router Amped Wireless
- router Cambium Networks
- router 3Com
- router WyreStorm
- router Ruckus Wireless
- router Dovado
- router Mach Power
- router EXSYS
- router NetComm
- router Comtrend
- router Premiertek
- router GL.iNet
- router Shinybow
- router Edgewater
- router Atlantis Land
- router Lumantek
- router Starlink
- router PulseAudio
- router Predator
- router Evolution
- router Luxul
- router StarIink
- router Silentwind
- router Keezel
- router United Telecom
- router Wisetiger
Legújabb útmutatók router
9 Április 2025
9 Április 2025
9 Április 2025
31 Március 2025
30 Március 2025
30 Március 2025
30 Március 2025
30 Március 2025
30 Március 2025
23 Március 2025