Használati útmutató Muse M-33 NY

Muse hi-fi rendszer M-33 NY

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Muse M-33 NY (4 oldal) a hi-fi rendszer kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

HX-2706 IB MUSE 001 REV1 GB

DATE:29-04-2013

AUX IN

1. Plug one end of cable (not included)

into the AUX IN socket (15) on the unit.

2. Plug the other end of the cable into the

Headphone or Line Out socket of the

external source.

GB - 2

POWER SUPPLY

2. The remote control unit operates on 2pcs

“AAA/UM4” battery (excluded). To

power up the remote control, open the

battery door, install the battery

according to the polarity diagram on the

battery compartment, then close the

battery door.

Before throwing any batteries away, consult your distributor who may be able

to take them back for specific recycling.

Important note

If an abnormal display indication or an operating problem occurs, disconnect the AC

power cord. Wait at least 5 seconds, then reconnect the AC power cord.

3. Press the

Unit will be automatically off after 4.5 hours without further operation.

STOP / FUNCTION button (20) on the unit or the FUNCTION button

(H1) on the remote control to select Auxiliary function. “AUX” indicator shows on

the display.

1. This micro system operates on AC230V~50Hz line power supply.

An external (auxiliary) audio source (i.e., personal CD player or MP3 player) can be

connected to this unit and heard through the speakers.

Installing Battery

Insert 2 “AAA/ UM4” batteries to the remote control prior to use. Make sure to match

their polarities (+/-) to the markings inside the compartment.

NOTES:

- In order to avoid leakage, always remove the batteries when unit will not be used for

a long period of time.

- If the remote control is not going to be used for a long time, remove the battery to

avoid damage caused by battery leakage corrosion. -

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type.

Track number “01” ,“CD”& the symbol “ ” will be shown during

normal compact disc playback.

Track number “001”,“CD”, the symbol “ ” & “MP3”will be shown during MP3 playback.

Track number “001”,“MP3”, the symbol “ ” & “USB” will be shown during USB

playback.

During Repeat 1

mode, display shows

During Repeat all

mode, display shows

During Random mode,

display shows

FOR NORMAL COMPACT

DISC PLAYBACK

To: PRESS:

Stop play

Pause play once

Resume play after pause again

Scan forward and backward and hold /

Skip tracks /

Repeat current track PLAY MODE once

Repeat all tracks PLAY MODE twice

Random play PLAY MODE three times

DISC ERROR

Note: If the disc is dirty, damaged or unreadable, or if the disc is placed upside down,

the “ ” indicator will appear on the display. If this occurs, clean the disc, insert the

disc correctly, or try another disc.

Unit will be automatically oﬀ after 30mins without any operation (in stop mode / CD

door open).

REPEAT, REPEAT FOLDER AND RANDOM PLAYBACK

Press PLAY MODE button (12) during unit ON mode.

CD plays with a single track repeat, all tracks repeat or

randomly.

FOR MP3/USB PLAYBACK

During Repeat 1

mode, display shows

During Repeat folder

mode,display shows

During Repeat all

mode, display shows

During Random mode,

display shows

RANDOM

GB -5

M-33CM

MICRO SYSTEM CD/MP3/USB

User Manual

Please read the instruction carefully

before operating the unit.

English GB - 1

LOCATION OF CONTROLS

REMOTE CONTROL

STANDBY BUTTON

PLAY/PAUSE BUTTON

F - SKIP BUTTON

+ 10 TRACK BUTTON

FOLDER UP BUTTON

PLAY MODE BUTTTON

MUTE BUTTON

VOLUME BUTTON

SPEAKER

POWER / STANDBY BUTTON

CD DOOR

REMOTE SENSOR

LCD DISPLAY

USB PORT

CD OPEN / CLOSE BUTTON

FM STEREO LED INDICATOR

PLAY / PAUSE BUTTON

VOL + BUTTON

F - SKIP / UP BUTTON

PLAY MODE BUTTON

FOLDER UP BUTTON

PROGRAM / CLOCK - ADJ.

BUTTON

AUX. IN JACK

PHONES JACK

BAND BUTTON

B - SKIP / DN BUTTON

VOL - BUTTON

STOP / CLEAR / FUNCTION

BUTTON

TUNING CONTROL

SPEAKER CORD

LEFT SPEAKER JACK

AC POWER CORD

RIGHT SPEAKER JACK

FM WIRE ANTENNA

FUNCTION BUTTON

STOP BUTTON

B - SKIP BUTTON

- 10 TRACK BUTTON

FOLDER DOWN BUTTON

PROGRAM/CLOCK-ADJ

BUTTON

BAND BUTTON

VOLUME BUTTON

H1.

H2.

H3.

H4.

H5.

H6.

H7.

H8.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

H9.

H10.

H11.

H12.

H13.

H14.

H15.

H16.

Press MUTE button (H15) to on/off mute function.

Note: The mute on is cancelled when:

a. The power is off/on

b. The Volume is adjusted by the VOL +/- button.

USING HEADPHONES (Headphones Not Included)

Connect a set of stereo headphones with 3.5mm mini plug to the phone jack on the

bottom panel. The speakers are automatically cut off when headphones are in use.

Note: To establish a safe headphones sound level:

Start your volume control at a low setting.

Slowly increase the sound until you can hear it comfortably and clearly, and without

distortion.

1. The player is on/off by pressing STANDBY (2/H9) button.

2. The function is selected cyclically by pressing

STOP / CLEAR / FUNCTION button:

CD USB TUNER AUX

Press

STANDBY button (2/H9) to turn on the unit,

then press VOLUME +/- control (10/H16, 19/H8)

to adjust the sound to comfortable level. The vol-

ume level will show on display for a few seconds.

GB - 3

AUDI O CONTROL

ADJUSTING THE SOUND

In full power, the continuous listening of the player may damage the user’s

hearing.

MUTE

To cut off the sound from the speakers temporarily, press the MUTE button (H15).

Press the MUTE button again to cancel Mute mode and restore the

sound from the speakers.

NOTE: When standby light is lit, unit is in OFF (standby) mode.

TO ADJUST THE VOLUME

VOLUME

VOL - VOL +

1. Press STANDBY button (2/H9).

2. Press the STOP / FUNCTION button to select CD.

3. Open the CD door(3) by pushing the CD door Open button (7).

4. Place the CD with label side up inside the CD compartment

and close the CD door (3).

5. After a few seconds, the total number of tracks and total

playing time will appear on the Multifunction display (5).

Press button (9/H10) to start playing the CD.

6. Press the PLAY/PAUSE button.

1. Turn on the unit by pressing STANDBY

button (2/H9).

2. Press the STOP (20/H2) /FUNCTION

(20/H1) button to select the tuner.

3. Press the BAND button (17/H7) to select desired band.

4. Tune to the desired radio station by using TUNING knob (21) and frequency is displayed.

5. Adjust the sound.

The clock is displayed on LCD display at standby mode.

1. Press the PROGRAM / CLOCK-ADJ.

button (14/H6).

2. Press the F-SKIP/UP (11/H11) or

B-SKIP /DOWN (18/H3) to select 12 hours

or 24 hours display.

3. Press the PROGRAM / CLOCK-ADJ. button

(14/H6), the hour digit flash.

4. Press the F-SKIP/UP (11/H11) or B-SKIP/DOWN

(18/H3) to adjust hour digit.

5. Press the PROGRAM / CLOCK-ADJ. button (14/H6), the minute digit flash.

6. Press the F-SKIP/UP (11/H11) or B-SKIP/DOWN (18/H3) to adjust

minute digit.

7. Press the PROGRAM / CLOCK-ADJ. button (14/H6) again, the correct time is

shown on display.

CLOCK SETTING

LISTENING TO THE RADIO

COMPACT DISC OPERATION

GB - 4

ANTENNA

For FM reception fully unwind the external FM wire antenna and adjust direction, for

optimum reception.

AFTER LISTENING

Turn off the unit by pressing STANDBY button (2/H9).

FOR MP3 PLAYBACK

Programmed playback enables folders/albums or tracks on a disc to be played in the

desired order. Up to 20 folders/albums or tracks can be programmed.

1. Press the “PROGRAM/CLOCK-ADJ.” button (14/H6).

2. Press the FOLDER DOWN (H5) /FOLDER UP (13/H13) button to select the

desired folder.

3. Press the / buttons to select the desired track number.

4. Press “PROGRAM/CLOCK-ADJ.” button (14/H6) again to memorize the track.

5. Repeat steps 2 to 4 until all desired tracks are programmed.

6. Press the “PLAY/PAUSE” button (9/H10) to start.

“PROGRAM” is shown on the CD display.

7. Press “STOP/FUNCTION” button to stop programmed playback.

8. Press “PLAY/PAUSE” button (9/H10) to resume programmed playback.

9. Press “STOP/FUNCTION” button again until “PROGRAM” disappear from

the display or turn off the CD player can clear the programmed memory.

Note : Programming can only be made when the player is in stop mode.

GB - 6

NOTE ON CD-R/RW DISCS

- CD-Rs or CD-RWs playback capability at this player may vary depending on quality

of media, CD-Burner, speed of burning and application software. Because of non

standardized format definition/production of CD-R/RW, playback-quality and

performance are not guaranteed.

- Manufacturer is not responsible for the playability of CD-R/RW due to recording

conditions such as PC performance, writing software, media ability, etc.

- Do not attach a seal or label to either side of the CD-R/RW disc. It may cause a

malfunction.

- Do not use your set immediately after transport from a cold place to a warm place,

there may be condensation problems.

FOLDER UP / DOWN

- Press FOLDER UP (13/H13) or FOLDER DOWN

(H5) button to select desired folder.

- Press B-SKIP/DOWN button (18/H3) or

F-SKIP/UP button (11/H11) to select desired track.

- Press PLAY/PAUSE button (9/H10) to start playing.

+10 / -10 BUTTON

These buttons allow you to advance 10 tracks at a time (+10) or go back 10 tracks at a

time (-10).

PROGRAM PLAYBACK

FOR NORMAL COMPACT DISC PLAYBACK

Programmed playback enables tracks on a disc to be played in the desired order. Up

to 20 tracks can be programmed.

-10 BUTTON

Same as +10 button (see above) except you can go back 10 tracks at a time. For

example, if Track 12 is playing and -10 is pressed, it will take you back to Track 2 (12-

10 = 2). You may also press -10 (H4) repeatedly (as above) to go back 10 tracks each

time -10 is pressed. If there are less than 10 tracks available, CD will go to the last

possible track.

+10 BUTTON

For example, if Track 1 is playing and +10 is pressed, it will take you to Track 11

(1+10 = 11). You may press +10 (13/H12) repeatedly to advance forward 10 tracks at

a time. (For example, when on Track 1, press once to Track 11 (1+10 = 11). Press

again to Track 21 (11+10 = 21).) If there are less than 10 higher tracks available, CD

will go back to Track 1.

1. Press the “PROGRAM/CLOCK-ADJ.” button (14/H6).

2. Press the / buttons to select the desired track number.

3. Press “PROGRAM/CLOCK-ADJ.” button (14/H6) again to memorize the track.

4. Repeat steps 2 and 3 until all desired tracks are programmed.

5. Press the “PLAY/PAUSE” button (9/H10) to start.

“PROGRAM” is shown on the CD display.

6. Press “STOP/FUNCTION” button to stop programmed playback.

7. Press “PLAY/PAUSE” buttons (9/H10) to resume programmed playback.

8. Press “STOP/FUNCTION” button again until “PROGRAM” disappear from the

display or turn off the CD player can clear the programmed memory.

USB OPERATION

1. Connect USB stick or MP3 player into the USB port.

2. Press STOP / FUNCTION button (20) to select USB.

3. Press PLAY / PAUSE button (9/H10) to start playback.

Note:

- USB connector does not design for communication with computer directly.

- Manufacturer is not responsible for the playability of USB disk or MP3 player due to

recording condition, capacity, interface compatibility, etc.

- Due to different formats, some USB stick or MP3 players may take longer time to be

read.

- USB stick is direct connected or with a cable with max. 0.5m length.

Unit will be automatically off after 30mins without any operation (in stop mode).

GB -7

- Do not expose discs to direct sunlight, high humidity, high temperatures or dust,

etc. Prolonged exposure to extreme temperatures can warp the disc (such as

leaving the disc in your car during summertime).

- When cleaning the disc, wipe in straight lines from the center of the

disc to the outer edge of the disc. Never wipe in circular motions.

Note: Always press STOP button and wait for the disc stop rotating

before opening the CD door to remove the disc.

- If there is a scratch, dirt or fingerprint on the CD, it may cause

tracking error. Before playing, clean the CD with a cleaning cloth.

Wipe the CD from the center out. Don’t store discs in places with

high temperatures or high humidity-they can become warped.

After playing, store the CD in its cases.

GB - 8

CARE AND MAINTENANCE

1. Clean the unit with a soft, damp (never wet) cloth. Solvent or detergent should

never be used.

2. Avoid operating your unit under direct sunlight or in hot, humid or dusty places.

3. Keep your unit away from heating appliances and sources of electrical noise such

as fluorescent lamps or motors.

- Handle the disc only by its edges. Never allow your ﬁngers to come in contact with

the shiny, unprinted side of the disc.

- Do not attach any tape, stickers, etc and/or write anything on either side of the disc.

- Clean the disc periodically with a soft, lint-free , dry cloth. Never use deter gents or

abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.

- If a disc skips or gets stuck on a section of the disc, it is probably dirty or damaged

(scratched).

- To remove a disc from its storage case,

press down on the center of the case

and lift the disc out, holding it carefully

by the edges. Discs should be stored

in their cases after use to avoid

scratches.

COMPACT DISC CARE

CLEANING THE LENS

A dirty lens will cause sound skipping. If the lens is very dirty, the player may not

work. We suggest using a special cleaning disk (not included) available in most

music and Hi-Fi stores. However, if you do not have one, you may use a cotton swab

very slightly dampened with alcohol to clean the lens.

GB - 9

CLEANING THE UNIT

- To prevent ﬁre or shock hazard, disconnect your unit from the AC power source

when cleaning.

- If the cabinet becomes dusty, wipe it with a soft cloth. Do not use any wax or polish

sprays on the cabinet.

- If the cabinet becomes dirty or smudged with fingerprints it may be cleaned with a

soft cloth slightly dampened with a mild soap and water solution. Never use

abrasive cloths or polishes as there will mar the finish of your unit.

ATTENTION: To reduce the risk of electric shock, do not remove

the cover. There are no user serviceable parts inside the unit. Refer

all servicing to qualified personnel.

The lightening flash with arrowhead symbol within the triangle is a warning

sign alerting the user of “dangerous voltage” inside the unit.

The exclamation point within the triangle is a warning sign alerting the user of

important instructions accompanying the product.

CAUTION: Invisible laser radiation when open and interlocks defeated. Avoid

exposure to beam.

WARNING

WARNING - To reduce the risk of fire or electric shock, do not expose this appliance

to rain or moisture.

SPECIFICATIONS

RADIO SECTION

Tuning ranges:

Antennas:

GENERAL

Output power:

Power consumption:

Speaker:

Phone jack:

Power source:

DIMENSIONS

Main unit:

Speaker:

Weight:

FM 88-108MHz

MW531-1620kHz

MW Built - in ferrite bar

FM wire antenna

1W + 1W (RMS)

16W

3½’’ 8 OHM

3.5MM

AC:230V~50Hz

143(L) x 227(D) x 179(H)mm

101(L) x 193(D) x 174(H)mm

2.6KGS

PRECAUTIONS

IMPORTANT

- Do not throw batteries in fire

- Do not be exposed to dripping or splashing, and that no object filled with liquids,

such as vases, shall be placed on the apparatus.

- Mains plug is used as the disconnect device and it shall remain readily operable.To

be completely disconnected the power input, the mains plug of the apparatus shall

be disconnected from the mains completely.The mains plug should not be

obstructed OR should be easily accessed during intended use.

- Attention should be drawn to the environmental aspects of battery disposal.

- No naked flame sources such as lighted candles should be placed on the apparatus.

- The use of apparatus is only in moderate climates.

- See markings on bottom / back of the product.

- Excessive sound pressure from earphones and headphones can cause hearing loss.

- Battery shall not be exposed to excessive heat such as sunshine, ﬁre or the like.

Heat- Do not use this unit near sources of heat, including heating vents, stoves, or

other appliances that generate heat.

Mounting surface- Place the unit on a ﬂat, even surface.

Ventilation- The unit should be situated with a adequate space around it so that

proper heat ventilation is assured. Allow 10 cm (4 in.) clearance from the near and

the top of the unit and 5 cm (2 in.) from each side.

- Do not place the unit on a bed, rug, or similar surface that may block the ventilation

openings.

- Do not install the unit in a bookcase, cabinet, or airtight rack where ventilation may be

impeded.

Object and liquid entry- Take care that objects or liquids do not get inside the unit

through the ventilation openings.

Condensation- Moisture may form on the CD Pickup lens when:

- The unit is moved from a cold spot to a warm spot

- The heating system has just been turned on

- The unit is used in a very humid room

- The unit is cooled by an air conditioner

When this unit has condensation inside, it may not function normally. Should this

occur, leave the unit for a few hours,then try to operate again.

GB - 10

If at any time in the future you should need to dispose of this product please

note that Waste electrical products should not be disposed of with house-

hold waste. Please recycle where facilities exist. Check with your Local Au-

thority or retailer for recycling advice. (Waste Electrical and Electronic Equip-

ment Directive)

GB - 11

Electric Power

1 Power sources- Use AC house current, as speciﬁed in the Operating instructions

and marked on the unit.

2 AC power cord

- When disconnecting the AC power cord, pull it out by the AC power plug. Do not pull the

cord itself.

- Never handle the AC power plug with wet hands, as this could result in fire or

electric shock.

- Power cords should be firmly secured to avoid being bent, pinched, or walked upon.

Pay particular attention to the cord from the unit to the power socket.

- Avoid overloading AC power plug and extension cords, beyond their capacity, as

this could result in fire or electric shock.

3 When not in use - Unplug the AC power cord from the AC outlet if the unit will not

be used for several months or more. When the cord is plugged in a small amount of

current continues to flow to the unit, even when the power is turned off.

Electrical Fast Transient (Burst) / ESD Remark:

- In case of misfunction due to electrical fast transient (Burst) or electrostatic discharge, just

reset the product (reconnect of power source may be required) to resume normal operation.

NEW ONE S.A.S

10, Rue de la Mission, 25480 Ecole Valentin, France

Termékspecifikációk

Márka:	Muse
Kategória:	hi-fi rendszer
Modell:	M-33 NY

Szüksége van segítségre?

Ha segítségre van szüksége Muse M-33 NY, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók hi-fi rendszer Muse

Muse M-30 BT Útmutató

1 Január 2025

Muse M-630 DWT Útmutató

2 Szeptember 2024

Muse M-380 GBS Útmutató

23 Augusztus 2024

Muse M-380 GB Útmutató

23 Augusztus 2024

Muse M-880 BTC Útmutató

15 Augusztus 2024

Muse M-38 BT Útmutató

3 Augusztus 2024

Muse MD-203 KB Útmutató

2 Augusztus 2024

Muse M-182 DB Útmutató

31 Július 2024

Muse M-70 DBT Útmutató

30 Július 2024

Muse M-620 BT Útmutató

30 Július 2024

Útmutatók hi-fi rendszer

Legújabb útmutatók hi-fi rendszer

NEC NP01SW1 Útmutató

9 Április 2025

Klipsch ProMedia Ultra 2.0 Útmutató

6 Április 2025

Vaxis Atom 500 Útmutató

2 Április 2025

INKEE Benbox Útmutató

1 Április 2025

JL Audio SlamPak SLPK-CAN-SPYDER1 Útmutató

31 Március 2025

Teradek Bolt 10K Útmutató

29 Március 2025

Teradek Bolt 500 Útmutató

29 Március 2025

Teradek Cubelet 655 Útmutató

29 Március 2025

Teradek Cube Series Útmutató

29 Március 2025

Teradek Cube 725 Útmutató

29 Március 2025