Használati útmutató Mtx Audio Thunder Marine WET75.4

Mtx Audio Vevő Thunder Marine WET75.4

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Mtx Audio Thunder Marine WET75.4 (32 oldal) a Vevő kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/32
OWNER’S MANUAL
WET SERIES AMPLIFIERS
M T X . C O M
Use your smartphone to scan or visit
youtube.com/user/MTXAudioUSA
to learn how to properly install this
amplifier.
M T X . C O M
2
PRODUCT INFORMATION
Model #
Serial #
Dealer’s Name
Date of Purchase
INTRODUCTION
Thank you for purchasing this MTX Audio Hi-Performance marine grade amplifier. Proper installation
matched with MTX speakers and subwoofers provide superior sound and performance for endless
hours of enjoyment on your boat wherever the current takes you. Congratulations and enjoy the
ultimate audio experience with MTX!
FEATURES
• Compact Size
• Double Sided PCB
• Surface Mount Components
• MOSFET Design
• LPF and HPF Crossover
• Adjustable Bass Boost
• Noise Free Design
• Short, Thermal, and High/Low Voltage Protection
• Conformal Coated PCB
• Plexiglass Cover for Controls
• Stainless Steel Hardware
• Rubber Gaskets Around RCA Connectors
CONTROL FUNCTIONS
1. Speakers - Connect speakers/subwoofers to these terminals. Be sure to check wire for proper
polarity. Never connect the speaker cables to the chassis ground.
2. +BATT (+12 Volt Power) - Connect this terminal through a FUSE or CIRCUIT BREAKER to the
positive terminal of the vehicle battery or the positive terminal of an isolated audio system
battery. WARNING: Always protect this power cable by installing a fuse or circuit breaker of the
appropriate gauge within 18 inches (45cm) of the battery terminal connection.
3. Remote Turn On - This terminal turns on the amplifier when (+) 12 volt is applied to it. Connect it to
the remote turn on lead of the head unit or signal source.
4. GND - Run an equal gauge wire from the Ground (GND) terminal on the MTX amplifier to the
negative terminal on the battery. Use the shortest distance possible. It is always a good idea to
replace the factory ground at this time with a cable equal or larger than the new amplifier power
cable. CAUTION: Do not connect this terminal directly to the vehicle battery
ground terminal or any other factory ground points.
5. RCA Input Jacks - These RCA input jacks are for use with source units that have RCA outputs. A
source unit with a minimum level of 200mV is required for proper operation. The use of high
quality twisted pair cables is recommended to decrease the possibility of radiated noise entering
the system.
6. Gain Control - The Gain control will match the amplifier’s sensitivity to the source units signal
voltage. The operating range is 5V to 200mV. This is NOT a volume control.NOTE:
M T X . C O M 3
7. Low Pass Filter Control (Mono Block) - This control is used to select the desired low pass x-over
frequency. The frequency can be adjusted from 40Hz to 220Hz for all bass mono models.
8. Subsonic Filter Control (Mono Block) - This control can filter out unwanted low frequency from
20Hz (OFF) to 50Hz. This function should only be used with vented enclosures.
9. Bass Boost Level Switch (Mono Block) - This switch can boost bass level by 0dB, 6dB, or 12dB.
The boost frequency is centered at 50Hz.
10. High Pass Filter (Full Range) - This controls the frequencies played for the front channels. Low
frequencies can be cut off from OFF to 200Hz. At OFF position, no low frequencies cut off,
meaning full range.
11. X-Over Mode and Frequency Control (Full Range) - These controls allow control over the
frequencies played for the rear channels. There is an option for Low Pass, Full Range, or High
Pass. In LP or HP mode, the crossover frequency can be tuned from 50Hz to 750Hz.
12. Power Indicator - This LED will light up when the amplifier is working properly.
13. Protection Indicator - The Red LED will light up and flash if there is a fault presented to the
amplifier. Please disconnect the amplifier and resolve the fault before reconnecting the amplifier.
PANEL LAYOUT
4-Channel Amplifier Panel Layout
1 4
6 13
3
10
2
6 12115

Termékspecifikációk

Márka: Mtx Audio
Kategória: Vevő
Modell: Thunder Marine WET75.4

Szüksége van segítségre?

Ha segítségre van szüksége Mtx Audio Thunder Marine WET75.4, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Vevő Mtx Audio

Mtx Audio

Mtx Audio MUD100.4 Útmutató

25 Augusztus 2024
Mtx Audio

Mtx Audio XThunder 800.5 Útmutató

14 Augusztus 2024
Mtx Audio

Mtx Audio RT8PT Útmutató

13 Augusztus 2024
Mtx Audio

Mtx Audio JackHammer JH5001 Útmutató

13 Augusztus 2024
Mtx Audio

Mtx Audio XThunder1200.1 Útmutató

12 Augusztus 2024
Mtx Audio

Mtx Audio Thunder Sports MUD100.2 Útmutató

12 Augusztus 2024
Mtx Audio

Mtx Audio Thunder Marine WET75.4 Útmutató

12 Augusztus 2024
Mtx Audio

Mtx Audio Thunder 1000.1 Útmutató

12 Augusztus 2024
Mtx Audio

Mtx Audio Thunder Marine WET500.1 Útmutató

11 Augusztus 2024
Mtx Audio

Mtx Audio RT1000-1D Útmutató

11 Augusztus 2024

Útmutatók Vevő

Legújabb útmutatók Vevő

Phonic

Phonic NT1304 Útmutató

12 December 2024
Phonic

Phonic Xtrix 4045 Útmutató

12 December 2024
Phonic

Phonic NT2508 Útmutató

12 December 2024
Phonic

Phonic MAX 500 Útmutató

12 December 2024
Phonic

Phonic DMX1502 Útmutató

12 December 2024
Phonic

Phonic XP6000 Útmutató

12 December 2024
Phonic

Phonic DMX5002 Útmutató

12 December 2024
Phonic

Phonic DMX802 Útmutató

12 December 2024
Phonic

Phonic MAX 1500 Plus Útmutató

12 December 2024
Phonic

Phonic NT1308 Útmutató

12 December 2024