Használati útmutató Mount-It! MI-397

Mount-It! Lapos panel támogatás MI-397

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Mount-It! MI-397 (2 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

please contact us

(Mount-It!) for assistance.

(Mount-It!) for a replacement.

please contact us

SKU: MI-397

TV Wall Mount with Extra Long Extension

The angle of the screen can be adjusted down up to 10 degrees and up 5 degrees. To adjust the tilt angle

of the TV, loosen the tilt adjustment nuts shown here then adjust the tilt to the desired angle then tighten the

nuts back down.

Note: If the screen tilts down slowly over time adjust the screen back to the proper angle and ensure the tilt

adjustment nuts are firmly tightened.

The mount allows up to 3 degrees of levelling adjustment post installation. To adjust the level of the TV

loosen the 2 nuts located behind the rectangular VESA plate, level the TV then tighten the 2 nuts again to

secure the TV in position.

Tilt Adjustment

4Levelling Adjustment

We recommend using professional installation services if you are unable to follow the instructions provided in this manual.

(855)- 925-5668

Please scan this QR code

to visit the product page.

+5°

-10°

S-5

-3° +3°

S-5

ø 6mm

(ø 1/4")

90mm

(3.5")

Wood Stud Installation Option

Attach the TV to the VESA Arms (No Spacers)

Attach the TV to the VESA Arms (With Spacers)

MI-397 80

WARNING: This installation manual is intended to provide guidance on how to install the TV mount and the TV on a suitable wall.

Please contact a qualified professional if you are unsure of the steps described in the manual or have doubts about the safety of the

installation. Improper installation may cause damage or serious injury. We cannot be held liable for damage or injury caused by

improper mounting. Incorrect assembly, inappropriate use or for use cases not explicitly specified in this document. If unsure, please

Mount and Accessories

TV Mounting Hardware

Wall Mounting Hardware

CHOKING HAZARD. Package includes small parts. Not for children under 3 years. Adult supervision is required

Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used.

Use the correct monitor mounting hardware suitable for your installation.

1. Use a stud finder to locate the wall studs and mark their location with a pencil.

2. Hold, tape or secure the Wall Template (#L) to the wall at the desired installation location. Use a bubble

level to ensure the straightness of the Wall Template (#L) and on the center of the studs mark the locations

for the 4 Lag Screws as shown. Once marked, remove the Wall Template.

3. Use a 1/4” drill bit and drill on the marked locations to a depth of 3.5”.

4. Hold the Mount (#M) to the wall over the holes and secure to the wall using all 4 Lag Screws (#A) and

Lag Washers (#B).

Select the appropriate size Mounting Bolt (Select one size #D, #E) and Square Washer (#C) for your

display’s mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the

correct bolt size for your display refer to your TV user manual or contact the TV manufacturer for sizing

information. Attach the 2 VESA Arms (#N) to the back of your TV using the selected bolts and washer.

If necessary, use the included spacers (#I, J) between the mount and the screen as shown above to adjust

the length of the mounting bolt. Multiple spacers can be used in combination to achieve the desired bolt

depth.

Select the appropriate size Mounting Bolt (Select one size #F, #G,#H) and Square Washer (#C) for your

display’s mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the

correct bolt size for your display refer to your TV user manual or contact the TV manufacturer for sizing

information. Attach the 2 VESA Arms (#N) to the back of your TV using the selected bolts, washer and

spacers.

Hang the TV on the mount arms as shown in the diagram. Caution: Use the help of a second person for

safe lifting and easier installation.

Attach the Safety Clips (#S-1 and #S-2) to the bottom of the VESA arms as shown here, and secure them

in place using Safety Bolts (#S-3).

1.Hold, tape or secure the Wall Template (#L) to the wall at the desired installation location. Use a bubble

level to ensure the straightness of the Wall Template and mark the locations for the 5 Lag Screws as

shown, then remove the template.

2.Use a 2/5” drill bit and drill on the marked locations to a depth of 3.7”. Note: Do not drill mounting holes

into mortar (such as between bricks or stones) only drill and install into solid stone or concrete surfaces.

3.Clear any dust and debris from the holes and insert the 5 Concrete Anchors (#K). Hold the Mount (#M) to

the wall over the holes and secure to the wall using all 5 Lag Screws (#A) and Lag Washers (#B).

Hang the TV on the Mount Arms

55kg

(121lbs)

Wall Mount

M (x1)

VESA Arms

N (x2)

Wall Template

L (x1)

Hex Wrench

S-4 (x1)

S-1 (x1)

Security Clips

S-2 (x1)

Security Bolt

S -3 (x2)

Wrench

S-5 (x1)

Square Washer

C (x4)

15mm Spacer

I (x4)

5mm Spacer

J (x4)

Concrete Anchor

K (5)

M4 14x (x4)

M6 14x (x4)

M6 30x (x4)

M8x20 (x4 )

M8 45x (x4)

Lag Screw

A(x5)

Lag Washer

B (x5)

132

X X

√

16/24 inches

Level the wall plate

6mm(1/4”)

B A

90mm (3.5”)

Concrete/Stone Installation Option

1b 95mm

(3.7")

ø 10 mm

(ø 2 /5")

X X

√

D/E

F/H

S-1/S-2

S-3

Termékspecifikációk

Márka:	Mount-It!
Kategória:	Lapos panel támogatás
Modell:	MI-397

Szüksége van segítségre?

Ha segítségre van szüksége Mount-It! MI-397, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Lapos panel támogatás Mount-It!

Mount-It! MI-14003 Útmutató

27 December 2024

Mount-It! MI-4753 Útmutató

27 December 2024

Mount-It! MI-14002 Útmutató

27 December 2024

Mount-It! MI-395 Útmutató

27 December 2024

Mount-It! MI-307 Útmutató

1 Szeptember 2024

Mount-It! MI-4761 Útmutató

1 Szeptember 2024

Mount-It! MI-6772 Útmutató

1 Szeptember 2024

Mount-It! MI-7906 Útmutató

1 Szeptember 2024

Mount-It! MI-606L Útmutató

1 Szeptember 2024

Mount-It! MI-397 Útmutató

1 Szeptember 2024

Útmutatók Lapos panel támogatás

Legújabb útmutatók Lapos panel támogatás

B-tech BTV520 Útmutató

6 Január 2025

AKAI 2342T Útmutató

2 Január 2025

Vogel's Base 45 M Útmutató

1 Január 2025

29 December 2024

29 December 2024

29 December 2024

29 December 2024

Chief RPA640 Útmutató

29 December 2024

Chief LCB1U Útmutató

29 December 2024

Chief RPMA204 Útmutató

29 December 2024