Használati útmutató Mercury 350.139UK
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Mercury 350.139UK (7 oldal) a detektor kategóriában. Ezt az útmutatót 10 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/7
www.avsl.com 350.139UK
Carbon Monoxide Alarm
Order ref: 350.139 UK
User Manual
An electromechanical alarm that saves lives by detecting carbon monoxide gas and giving a
loud acoustic warning if this poisonous gas is present. The alarm is battery powered and
incorporates an LCD display screen which constantly shows the current CO levels. An essential
life saver needed in every household with gas or solid fuel heating. Recommended positioning,
in all rooms with boilers, stoves or open fires.
Product Specifications:
Apparatus
Type B
Batteries
3 x Alkaline AA (supplied)
Alarm level
85dB @ 3m
Sensor
Electromechanical
Operating temperature
0°C to 45°C
CO Alarm Level
27ppm - 55ppm: within 60 to 90 mins, 110ppm:
within 10 to 40 mins, 330ppm: within 3 mins
Humidity
0 to 90% RH
Lifetime
10 years from date of manufacture
Dimensions
110 x 77 x 37mm
Weight
2 g (incl. batteries) 03
Product layout:
1. Alarm casing
2. LCD display
3. Speaker
4. Power indicator
5. Fault indicator
6. Alarm indicator
7. Test button
8. Sensor inlet
9. Battery compartme nt
10. Mounting plate lugs
11. Mounting plate
12. Screw holes
13. Mounting plate slot
www.avsl.com 350.139UK
Installation:
Start up:
Remove the alarm from the packaging and slide the back cover across to reveal the battery
compartment. Insert the 3 x AA batteries (supplied) to the correct polarity ensuring t safety he
latches are pressed underneath. The alarm will beep once, the LCD display will read as “EN”
below and all 3 LEDs will flash to indicate power up. When the LCD display on the front starts
to display information, the alarm is successfully powered and has start working. ed
Location:
For houses and buildings with multiple rooms, it is recommended to install one alarm per
room. If not possible then at least one alarm per level. It is advised to locate the alarm near
the potential source of CO, such as rooms with a boiler, fireplace or gas oven. For optimum
detection, the alarm needs to be installed at least 1.5m above the ground, 0.3m below the
ceiling and 1.5m from the corner of the room.
DO NOT locate alarm:
• Next to a window or a door.
• On the floor where the unit may get kicked or damaged.
• Behind fans, air-con units or any sort of ventilation.
• Confined spaces such as inside a cupboard.
• Behind furniture or curtains, alarms must not be obstructed.
• Cold or hot environments. (no less than 0ºC or no more than 45°C)
• Dusty areas, this may block the sensor.
• Too close to an open flame, this can leave carbon deposits on the sensor, reduce its
sensitivity and give false readings.
• Directly above a heater or cooking appliance.
www.avsl.com 350.139UK
• Where a lot of moisture is present, e.g. bathroom or kitchen above a sink or hob.
• Outdoors, this alarm is designed for indoor use only.
Installation:
After finding an appropriate location, the wall bracket can be screwed onto the wall using the
supplied hardware. Alternatively, it can be stuck on using a seld adhesi pad or just stood on ve
top of a unit or shelf.
To mount the bracket using hardware, use the mounting plate as a guide to mark the two
holes. Drill these holes 6mmØ, 30mm deep. Insert the plugs into the hole and screw the
bracket on, ensuring the raised side is facing outward.
Push the back of the alarm against the bracket and slide across until it clicks to lock in place.
The battery compartment has latches that rise to prevent the alarm being installed without
batteries, therefore please ensure the batteries are inserted before installing the alarm.
Operation:
The LCD screen and LEDs on the front of the alarm give vital information of the working
condition of the alarm and important ambient readings of the surroundings.
When the alarm is powered, the green power LED will flash once every 45 seconds to indicate
it is working. When the working voltage drops below 3.5V, the alarm will beep when the
power LED flashes. This indicates the battery power is insufficient; please replace the batteries
as soon as possible. On the LCD display, the battery status is also shown constantly:
Indicates batteries are at full capacity and alarm is working with sufficient power.
Indicates batteries have sufficient capacity and alarm is working with sufficient power.
Indicates batteries capacity is getting low but alarm still has sufficient power.
Indicates batteries are critically low and alarm is working on the minimum required
power and requires replacement as soon as possible keep the alarm functional. to
It is recommended to manually perform testing once a week. To perform a manual test,
simply press the test button for 1 second and the alarm will enter test mode. The Alarm LED
will flash and the alarm will sound 5 times the unit . The LCD screen will read “---“ to indicate
is in test mode.
All LEDs and the LCD display should resume back to normal after a few seconds.
The alarm will perform self-checking of the sensor every 2 minutes. Under normal conditions
no LEDs will flash. If the sensor fails, the amber fault LED will flash once every 2 minutes
Termékspecifikációk
| Márka: | Mercury |
| Kategória: | detektor |
| Modell: | 350.139UK |
Szüksége van segítségre?
Ha segítségre van szüksége Mercury 350.139UK, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók detektor Mercury
30 December 2025
4 Augusztus 2024
8 Május 2024
Útmutatók detektor
- detektor National Geographic
- detektor Dometic
- detektor Nedis
- detektor Bosch
- detektor Evolveo
- detektor Voltcraft
- detektor Vimar
- detektor ORNO
- detektor Hikvision
- detektor Techno Line
- detektor DSC
- detektor V-TAC
- detektor Toolcraft
- detektor Chauvin Arnoux
- detektor Dahua Technology
- detektor Cobra
- detektor Denver
- detektor Black & Decker
- detektor Beha-Amprobe
- detektor X4 Tech
- detektor Joy-It
- detektor Testo
- detektor Nexa
- detektor Powerfix
- detektor Garrett
- detektor Ei Electronics
- detektor Alecto
- detektor Honeywell
- detektor Velleman
- detektor FireAngel
- detektor Trotec
- detektor Sauter
- detektor Elro
- detektor Fluke
- detektor Busch-Jaeger
- detektor Olympia
- detektor Metrix
- detektor ZKTeco
- detektor Abus
- detektor Marmitek
- detektor Pyle
- detektor Steinel
- detektor IFM
- detektor Kyoritsu
- detektor Uniden
- detektor Steinberg
- detektor Homematic IP
- detektor Axis
- detektor Optex
- detektor Soler & Palau
- detektor Multimetrix
- detektor SureCall
- detektor Schwaiger
- detektor Laserliner
- detektor Smartwares
- detektor IGET
- detektor AngelEye
- detektor Amprobe
- detektor Brennenstuhl
- detektor Sun Joe
- detektor Techly
- detektor Marquant
- detektor Ferrex
- detektor Perel
- detektor Flir
- detektor Royal Sovereign
- detektor AcuRite
- detektor Grothe
- detektor Netatmo
- detektor Hager
- detektor BRK
- detektor Duro
- detektor Xavax
- detektor Jung
- detektor Satel
- detektor X-Sense
- detektor Gamma Scout
- detektor Ferguson
- detektor Ebode
- detektor Escort
- detektor System Sensor
- detektor Inovonics
- detektor Guardian Avionics
- detektor Thitronik
- detektor Whistler
- detektor Cavius
- detektor Pentatech
- detektor PCE Instruments
- detektor Flow Smoke Detector
- detektor Benewake
- detektor BeeSecure
- detektor Fisher
- detektor Schabus
- detektor Zircon
- detektor Protector
- detektor Sanwa
- detektor Resideo
- detektor STI
- detektor HT Instruments
- detektor BlendMount
- detektor K40
- detektor Gewiss
- detektor Seco-Larm
- detektor Silent Knight
- detektor Seaward
- detektor GEV
- detektor S.E. International
- detektor Rocky Mountain
- detektor Skyscan
- detektor Bearware
- detektor Winland
- detektor Noyafa
Legújabb útmutatók detektor
4 Január 2025
31 December 2025
31 December 2025
31 December 2025
30 December 2025
29 December 2024
29 December 2024
28 December 2024
21 December 2024
21 December 2024