Használati útmutató Memphis Audio SRX300.4V

Memphis Audio Vevő SRX300.4V

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Memphis Audio SRX300.4V (9 oldal) a Vevő kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/9
MODELS: SRX150.2V // SRX300.4V
FULL RANGE AMPLIFIER
INSTRUCTION MANUAL
STREETREFERENCE
Features
Memphis Audio built a 50 year legacy in the audio industry engineering the highest quality products to produce
the best possible listening experience for our fans and loyal supporters. To fully appreciate our products we
recommend taking the time to read and follow the instructions in this manual. As always, we recommend all
installations and service be performed by an authorized Memphis Audio dealer.
• 2 stereo stable / 4 mono ˜ ˜
• High & low level inputs
• 0/6/12dB bass boost
• Bridgeable & tri-mode operation
• Protection circuitry: overload, short circuit, thermal & reverse polarity
Bridgeable & Tri-Mode Operation
Street Reference amplifiers can be used in stereo, bridged or tri-mode operation. Tri-mode operation means that a pair of
speakers are wired in the conventional stereo manner while a subwoofer is simultaneously connected to the bridged terminals
of the same two channels. This is useful for simple 2-channel systems that require a subwoofer in addition to the full range
speakers
Nickel Plated Connectors
Ensures solid electrical connection that resist corrosion
Fully Variable High & Low Pass Crossovers
Fully variable crossovers promote installation ease and save the cost of outboard crossovers. Additionally, thy may be used in
conjunction with outboard passive or active crossovers depending on the complexity required by the system. The 12dB per
octave slope offers roll-off above or below the selected frequency.
Protection Circuitry
Protects against overload, short circuit, thermal and reverse polarity. These protection features are designed to protect the
amplifier from misuse as well as from common causes of amplifier failure.
LED Light
Blue light indicates that the amplifier is working normally. If the light is not illuminated or is glowing red, consult the
troubleshooting section of the manual.
For optimal performance, Memphis recommends using only Memphis Connection accessories. Outfitting
your system with properly sized Memphis Connection wire and accessories will dramatically boost your
listening experience and increase the durability of your Memphis Audio products.
Check out our full line of Street Reference speakers and subwoofers to create a complete Memphis
Street Reference system.
Street Reference amplifiers feature a MOSFET power supply with a 12dB per octave crossover to ensure the most
accurate musical reproduction. All models feature a fully variable crossover with 12db per octave slopes allowing
you the ability to tailor the sound to best fit your speakers and listening preferences.
STREET REFERENCE MULTI CHANNEL AMPLIFIERS
SRX150.2V // SRX.300.4V
• Textured aluminum heatsink
• Selectable bass boost
• Variable crossover network
• Ultra-bright LED accent light strip
STREETREFERENCE
When troubleshooting your amp, speaker and speaker wires should be tested first.
For your safety, always inspect the mounting location carefully to ensure you are not drilling into any electrical,
hydraulic, fuel or fluid lines. Always check your speaker load with a multi-meter before connecting the amplifier.
Connecting any speaker load lower than the rated impedance of the amplifier will result in damage to the amplifier.
Damage of this nature is NOT covered under warranty. Please pay close attention to what connections are made to
the amplifier.
If you are uncertain or uncomfortable proceeding with your installation, please contact your local
authorized Memphis Audio Dealer
No Output:
• Confirm all wiring is firmly connected.
Both +12V and REM terminals must have +12 Volts present and GND must be connected to chassis’ ground or to
the negative battery terminal.
• Confirm the signal source is connected and supplying an output signal. To confirm the amp is working, connect
an RCA patch cord to the line inputs of the amplifier (do not connect the other end of the patch cord). Briefly tap
the center pin of each disconnected RCA with your finger. This should produce a noise (brief static or hum) in
the speakers.
• If the amp is hot, check the speaker impedance or load. The total minimum impedance of all speakers should
not be lower than the rating of the amp.
Only One Channel Works:
• Confirm the speaker terminal strip connections are firmly connected.
• Check “balance” control on your signal source.
• If using RCA Low-Level inputs, reverse the input plugs at the amplifier. If the channel that is silent reverses
position, the problem is in the source unit or connecting cable.
Weak Output
• Check input sensitivity control adjustment.
Unwanted Noise
• Whine that increases and decreases with engine speed - confirm the Amp & Source unit are grounded properly.
• Clicking or popping noise at a rate that follows engine speed - this is often induced by the vehicles ignition system.
Confirm that the vehicle is equipped with resistor spark plugs and wires. The ignition system may need service.
• Noise can be caused by routing speaker input wires too close to the light wires and other accessory wires in the
vehicle. Re-route wires to avoid unwanted interference.
• If above steps do not improve/reduce noise, the system should be checked by a professional audio installer at a
Memphis Authorized Dealer.
Red LED is Illuminated
• Speaker or wire is shorted • Battery voltage too low
• Battery voltage too high • Amplifier has overheated due to improper ventilation
Troubleshooting
Warning
Installation Information
Memphis Audio recommends the installation of our products to be performed by an Authorized dealer. Attempting
an installation project on your own or through an unauthorized source may result in damage to your products and
may potentially void your warranty.
Amplifiers are generally mounted in the hatch/trunk area of your vehicle or behind the seat of most pick up trucks.
Select a location that provides adequate ventilation. Amplifier should be secured using the screws provided.

Termékspecifikációk

Márka: Memphis Audio
Kategória: Vevő
Modell: SRX300.4V

Szüksége van segítségre?

Ha segítségre van szüksége Memphis Audio SRX300.4V, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Vevő Memphis Audio

Memphis Audio

Memphis Audio PRX400.1V2 Útmutató

3 Szeptember 2024
Memphis Audio

Memphis Audio PRX500.4V2 Útmutató

3 Szeptember 2024
Memphis Audio

Memphis Audio Mojo Pro MJP1000.1 Útmutató

3 Szeptember 2024
Memphis Audio

Memphis Audio PRX1500.1V2 Útmutató

3 Szeptember 2024
Memphis Audio

Memphis Audio PRX800.1V2 Útmutató

3 Szeptember 2024
Memphis Audio

Memphis Audio Mojo Pro MJP3000.1 Útmutató

3 Szeptember 2024
Memphis Audio

Memphis Audio MJP750.1 Útmutató

1 Szeptember 2024
Memphis Audio

Memphis Audio SRX1200.1V Útmutató

1 Szeptember 2024
Memphis Audio

Memphis Audio SRX300.4V Útmutató

1 Szeptember 2024
Memphis Audio

Memphis Audio MX150.2-24V Útmutató

1 Szeptember 2024

Útmutatók Vevő

Legújabb útmutatók Vevő

Yamaha

Yamaha Aventage RX-A4A Útmutató

9 Április 2025
Yamaha

Yamaha Aventage RX-A8A Útmutató

9 Április 2025
DJI

DJI D-RTK 3 Útmutató

5 Április 2025
Phonocar

Phonocar PH544 Útmutató

5 Április 2025
QSC

QSC SPA-Qf 60x2 Útmutató

2 Április 2025
Harper

Harper HDT2-5010 Útmutató

2 Április 2025
Harper

Harper HDT2-2010 Útmutató

2 Április 2025
Alpine

Alpine MRX-F65 Útmutató

31 Március 2025
Streacom

Streacom TL1 Útmutató

31 Március 2025
Pro-Ject

Pro-Ject Stereo Box DS Útmutató

30 Március 2025