Használati útmutató MB Quart MBQR-RAD-2

MB Quart nincs kategorizálva MBQR-RAD-2

Olvassa el alább 📖 a magyar nyelvű használati útmutatót MB Quart MBQR-RAD-2 (59 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/59
DASHBOARD
DISASSEMBLY INSTRUCTIONS
for Polaris® RZR® Vehicles
Instruction Manual
MBQR-RAD-2
2©2020 Maxxsonics USA, Inc.
THANK YOU!
Congratulations for choosing the MBQR-RAD-2, an AM/FM/WB, USB and Bluetooth
Multimedia Controller by MB Quart. The unit and housing are engineered to t 2013 and
newer Polaris® RZR® vehicles. For more detailed information about the product, the
operator/install manual* and a video tutorial, please visit MBQuart.com.
*Wiring information, installation steps and operation of the MBQR-RAD-2 source unit are in the
Operator's Guide and Installation Instructions pictured at right.
INSTALLATION TIME
About 1.5 hours are required to complete this installation, not including other system
components. These instructions are for dashboard disassembly only.
TOOLS AND SUPPLIES NEEDED
● Wire Strippers and Crimpers ● Flush Cut Wire Cutters (for trimming zip-ties)
● Bojo Tools (Pry Tools) ● T40 Torx Driver
● Ratchet w/ 10mm Socket ● T25 Torx Driver
● (Optional) Soldering iron, solder and heat shrink tubing or high-quality electrical tape
SAFETY PRECAUTIONS
Safely prepare your machine for the MBQR-RAD-2 installation before proceeding.
● Turn the ignition off and remove the key
● Use a packing blanket other soft material to protect your machine
● Safety Glasses - always wear eye protection
PREPARATION FOR INSTALLATION
Before dismantling your vehicle, we suggest you prepare your tools, the MBQR-RAD-2 and its wiring as
increases efciency to have everything ready when each component is installed.
STEP 1 – REMOVE SEATS
Remove driver and passenger seats by pulling on the
lock clip shown in Figure 1-1 This lock clip is located
between the bottom and upright portion of the seat.
Removing both seats will give you the room to work in
the kick panel areas, in addition to getting access to the
battery for Step 2.
STEP 2 – REMOVE NEGATIVE BATTERY CABLE
Using a 10mm socket and ratchet, remove the negative
battery terminal and set aside as shown in Figure 1-2.
This safety measure ensures you do not have any
accessories powered during the installation, as well as
keeps the battery from unnecessarily draining.
Figure 1-1
Figure 1-2
PRE-INSTALLATION
Operator’s Guide and
Installation Instructions
MBQR-RAD-2
AM/FM/USB/Blu etooth®
Mul timedi Contr oller and a
fo Polarisr ® RZR® Vehicles
MBQR-RAD-2
Operator's Guide and
Installation Instructions
3
DISASSEMBLY
DASH AREA DISASSEMBLY 2013-2018 (Non-Turbo S) RZR
Please note, separate disassembly instructions for the 2018.5 Turbo S and 2019+ RZR models are found on
pages 5-8 in this manual.
STEP 1 – REMOVE CENTER HOOD
Start with removing the hood as shown in Figure 5-1.
Twist the tabs at the upper left and right corners. Pull
up to remove. This is where you will access the bus
bar to make power connections for your source unit.
Conrm that your machine has the bus bar harness
installed. If your bus bar harness has not been installed,
you can purchase from your dealer or Polaris online.
The part numbers are 2881551 or 2881646 depending
on which specic RZR model you own.
STEP 2 - REMOVE TOP OF DASH
Remove (2) T40 screws as shown in Figure 5-2. Slide
dash forward to access back of dash and unplug gauges and switches one at a time. Set dash aside in a
safe location. This will provide wiring access.
STEP 3 – REMOVE THE GRAB BAR
Remove the grab bar as shown in Figure 5-3 by removing the retaining clip and pin and rmly pulling the
grip toward the rear of the vehicle.
STEP 4 - REMOVING DASH POCKET & REAR MOUNT
To remove the DIN dash pocket from the dash, locate the rear support bracket at the rear of the pocket and
remove the T40 Torx head screw as in Figure 5-4. Next, remove the clip shown on the right from the back
and pull out the plastic pocket. Set aside the retaining clip shown in Figure 5-5 for re-use when mounting the
MBQR-RAD-2 source unit.
Figure 5-1
Figure 5-2
Figure 5-3
Figure 5-4
T40 Torx Screw
Set aside OEM dash clip for source unit mounting
later in the installation as its reused when you are
installing an MB Quart MBQR-RAD-2.
Figure 5-5

Termékspecifikációk

Márka: MB Quart
Kategória: nincs kategorizálva
Modell: MBQR-RAD-2

Szüksége van segítségre?

Ha segítségre van szüksége MB Quart MBQR-RAD-2, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva MB Quart

MB Quart

MB Quart MBQ-CAM-1 Útmutató

25 Augusztus 2024
MB Quart

MB Quart MBQX-STG2-RAD-1 Útmutató

24 Augusztus 2024
MB Quart

MB Quart MBQX-STG5-1 Útmutató

14 Augusztus 2024
MB Quart

MB Quart Nautic N2-RC Útmutató

23 Július 2024
MB Quart

MB Quart MBQX-STG3-1 Útmutató

19 Július 2024
MB Quart

MB Quart MBQR-RAD-2 Útmutató

16 Július 2024
MB Quart

MB Quart MBQR-STG3-RC1 Útmutató

5 Július 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

Roland

Roland SD-20 Útmutató

16 Október 2024
SilverCrest

SilverCrest SRG 1300 C3 Útmutató

16 Október 2024
IFM

IFM TY0058 Útmutató

16 Október 2024
Thule

Thule Kit 186039 Útmutató

16 Október 2024
Blumfeldt

Blumfeldt Solidflor Útmutató

16 Október 2024
Dimplex

Dimplex QRAD200E Útmutató

16 Október 2024
DAS Audio

DAS Audio AX-112-5 Útmutató

16 Október 2024
Ferplast

Ferplast Ergocomfort Freetime Útmutató

16 Október 2024
AEG

AEG MECK52 Útmutató

16 Október 2024
Black Diamond

Black Diamond BD1121530000ALL1 Útmutató

16 Október 2024