Használati útmutató Maximum 1335

Maximum Mérőberendezések 1335

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Maximum 1335 (20 oldal) a Mérőberendezések kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/20
MAXIMUM
DIGITAL SATELLITE FINDER
USER’S MANUAL
Item no. 1335
Precautions
Please read this manual carefully before using this device for the rst
time.
The technical specications and operating methods included in this
manual are subject to changes without notice. In case of any inquires
after a period of usage, please contact the manufacturer.
When charging in the car, it is necessary in POWER OFF state. Can
not charge fully phenomenon will be occurred by the low voltage.
Please make sure of charging the battery before using for the rst
time.
Recommend 5 hours.
1
Table of Contents
Chapter . IntroductionⅠ
Chapter . Menu OperationⅡ
A. Front panel……………………..………………….....3
B. Quick operation…………………….…..…………….6
1. System setup……………….…………………….6
2. Quick operation guide…………………………...7
C. Detail operation guide…………….…….……………11
1. LNB configuration………………………………11
2. Signal finding……………………………………12
3. System setup……………………..……………...15
4. Angle calculation…………………..……………16
5. Software upgrade…………………..……………17
6. Spectrum…………………………..…………….18
7. Channel Information…………..………………...18
8. Channel List…………………..…………………19
2
Chapter IntroductionⅠ
Digital satellite nder is simple and convenient for setting and
aligning a satellite dish. With the parameters of satellite, you can set
and align a satellite dish quickly, easily and accurately.
Chapter FunctionⅡ
A. Front panel
3
1. LNB INPUT
Satellite signal input port; connect directly to satellite antenna with
coaxial cable.
2. LCD Screen
Shows menus and programs clearly
3. Power Light
Indicates ON/OFF mode
4. Lock Light
This light will be on when signal is locked.
5. 22k/13v/18v light:
Indicates the mode of 22k/13v/18v
6. Function key
Consist of 2 keys, F1- F2
F1: Changes the signal bar on SIGNAL FINDING menu
F2: Actives DiSEqC 1.2 function on the SIGNAL FINDING menu
AN/DG: Actives the spectrum on the SIGNAL FINDING menu
0/22K: A quick key to switch 22K output on the SIGNAL
FINDING menu
H/V: A quick key to switch 13V/18V output on the SIGNAL
FINDING menu
7. Arrow key and OK key
Use Arrow key to browse the item, press OK key to select
8. Numerical key
Enters numerical settings directly.
9. FIND key
Accesses easy satellite nd menu that sets and aligns a satellite dish
quickly
10. MENU key
Enters and exits the main menu
4
11. EXIT key
Exits from the present menu and backs to the previous one
12. ANGLE key
Accesses the AZ, EL and Polarity calculation menu
13. SYSTEM key
Sets up all system parameters
14. POWER key
For turn-on/ turn-o. To press and hold for 3 seconds to power on the
device
15. TV/RADIO
Selects and plays TV/RADIO channel in playing mode.
16. AV(optional)
Shifts AV output / AV input
17. Charge port
Connects with the charger cord.
18. USB port
Connects with USB disk for upgrade.
19. R/L/VIDEO
Output audio and video signal
20. AV IN
Input the audio and video signal to LCD screen.
21. HDMI
Audio and video output socket for the high denition television set
5
B. Quick operation
With this function, user can quickly and easily point the right satellite
and accurately set the dish.
Press ON/OFF button to turn on/o the device.
1) System Setup
Press the SYSTEM button to display the setting menu.
<See Figure B-1>
<Figure B-1>
① Menu language: Use LEFT/RIGHT button to change the language
items. Select the language that you need.
② Transparency: Use LEFT/RIGHT button to adjust the OSD
transparency of all the menu of the receiver
③ Aspect Ratio: Use LEFT/RIGHT button to choose 4:3, 16:9 (wide
screen) and auto
④ Display Format: If you select the display aspect ratio as “4:3”, then
also the preferred aspect ratio conversion scheme for cases in which
the transmitted Programme is in “16:9” format can be chosen.
6
The options are:
Pan & Scan: The receiver interprets pan & scan vectors
encoded in the Programme and crops the 16:9 input signal for
display on 4:3 TV.
Letterbox: In this mode the original aspect ratio of the 16:9
input video signal is preserved, thus there are vertical black
bars on the top and bottom of the screen.
Ignore: Use this setting, if your TV set handles the aspect ratio
conversion
⑤ Video Format: Please choose from the available resolutions 1080p /
1080i , 720p or 576p
⑥ Factory reset: All Parameters are reset to Factory Programming
2) Quick operation guide
1. FIND
<FigureB- 2>
① Satellite: Use LEFT/RIGHT button to select the satellite or Press
OK button to select the Satellite
② LNB: Use LEFT/RIGHT button to select the LNB or Press OK
button to setup LNB conguration.
7
③ Dish position: Fixed or Moved
④ Frequency: Use LEFT/RIGHT button to select the TP frequency or Press OK
button to enter TP table setup
⑤ Network search: Use LEFT/RIGHT button to choose ON/OFF
⑥ TP SCAN: Scan transponders one by one. Press OK to start scan
channel. See gure
⑦ SAT SCAN: Scan all the transponders in one satellite (these
transponders have been set)
⑧ In the course of signal searching, you can see the bar meter of the
LEVEL and QUALITY, at the same time the LOCK light will come
on with the speaker notication. DiSEqC will indicate which port is
connected to the DiSEqC 1.0 switch.
2. AN/DG
<FigureB- 3>
the spectrum of current satellite will be displayed as gure B-3
3. H/V
A quick key to switch 13V/18V output on the SIGNAL FINDING menu
8
4. 0/22K
A quick key to switch 22K output on the SIGNAL FINDING menu
5. Press AV
Shifts AV output / AV input
6. T/R
Press TV/RADIO key in the playing mode to shift
9
7. ANGLE
<FigureB- 4>
① Satellite: Use LEFT/RIGHT button to select the satellite or
Press OK button to select the Satellite
② Sat longitude: Use numerical button to enter satellite position
③ East/West:Use LEFT/RIGHT button to select satellite position
is East or West.
④ User latitude: Use numerical button to enter latitude of your
position.
⑤ North/South: Indicate if latitude is North or South
⑥ User longitude: Use numerical button to enter longitude of
your position.
⑦ East/West: Indicate if longitude is East or West
⑧ ANGLE CALCAULATION Press OK button to calculate ：
azimuth and elevation of dish
10
C. Detail operation Guide
1) LNB Conguration
<FigureC- 1>
Press OK on LNB Conguration then the following window
appears. <See Figure C-2>
<FigureC- 2>
(a). LNB: Use LEFT/RIGHT button to select the LNB
(b). L.O. Frequency: Use numerical button to enter the LOF value
in GHz
11

Termékspecifikációk

Márka: Maximum
Kategória: Mérőberendezések
Modell: 1335

Szüksége van segítségre?

Ha segítségre van szüksége Maximum 1335, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Mérőberendezések Maximum

Maximum

Maximum 1335 Útmutató

12 Augusztus 2024

Útmutatók Mérőberendezések

Legújabb útmutatók Mérőberendezések

Uni-T

Uni-T UT220 Útmutató

3 Április 2025
Uni-T

Uni-T UT681C Útmutató

3 Április 2025
Uni-T

Uni-T UT216C Útmutató

3 Április 2025
Uni-T

Uni-T UT611 Útmutató

3 Április 2025
Uni-T

Uni-T UT210D Útmutató

3 Április 2025
Uni-T

Uni-T UT210C Útmutató

3 Április 2025
Uni-T

Uni-T UT210B Útmutató

3 Április 2025
Uni-T

Uni-T UT682 Útmutató

3 Április 2025
Uni-T

Uni-T UT275 Útmutató

3 Április 2025
Uni-T

Uni-T UT08A Útmutató

3 Április 2025