Használati útmutató Makita RP2302FC
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Makita RP2302FC (1 oldal) a marógép kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-000288 Rev01
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-228, SSM-228, SLB-228 and SLM-228 Interface Brackets
SSB-228, SSM-228, SLB-228 and SLM-228 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place nylon spacers on bottom of projector and align them with threaded inserts.
4. Place the interface bracket onto the bottom of the projector and align it with the holes in the bracket with the threaded inserts and nylon
spacers on the bottom of the projector.
5. Position M4 x 20mm pan head mounting screws with M4 washers, and M4 x 20mm flat head mounting screws into the mounting holes.
Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (3) Washer, Flat, M4
(4) 10-24 Thumb Nuts ** (3) Screw, Phillips Pan Head, M4 x 20mm
(1) All-Points Security Kit (2) Screw, Phillips Flat Head, M4 x 20mm
(5) Spacer, Nylon, .500 OD x.194 ID x .500
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-228 SLM-228
(Note: SSB-style interfac
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
N
o
t
e
:
S
S
M
-
s
t
y
l
e
i
n
t
e
r
f
a
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
Towards front of
projector
Towards front of
projector
Termékspecifikációk
| Márka: | Makita |
| Kategória: | marógép |
| Modell: | RP2302FC |
Szüksége van segítségre?
Ha segítségre van szüksége Makita RP2302FC, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók marógép Makita
15 Október 2024
28 Augusztus 2024
28 Augusztus 2024
19 Augusztus 2024
3 Augusztus 2024
7 Július 2024
14 Június 2024
Útmutatók marógép
- marógép Parkside
- marógép Worx
- marógép Bosch
- marógép Einhell
- marógép Flex
- marógép Mafell
- marógép Güde
- marógép Hitachi
- marógép Black & Decker
- marógép PowerPlus
- marógép Texas
- marógép Grizzly
- marógép Festool
- marógép Yato
- marógép Trotec
- marógép DeWalt
- marógép Stanley
- marógép Vonroc
- marógép Holzmann
- marógép Skil
- marógép Meec Tools
- marógép Trend
- marógép Maktec
- marógép Bort
- marógép Power Craft
- marógép Eibenstock
- marógép Topcraft
- marógép Carat
- marógép Duro
- marógép Truper
- marógép Kinzo
- marógép Bruder Mannesmann
- marógép Rupes
- marógép Westfalia
- marógép Stomer
- marógép Elu
- marógép Triton
- marógép Anova
- marógép Rikon
- marógép Felisatti
- marógép Toledo
- marógép CMT Orange Tools
Legújabb útmutatók marógép
28 December 2024
23 December 2024
15 Október 2024
4 Október 2024
20 Szeptember 2024
8 Szeptember 2024
4 Szeptember 2024
4 Szeptember 2024
4 Szeptember 2024
2 Szeptember 2024