Használati útmutató LumenRadio CRMX Galileo TX

LumenRadio vezérlő CRMX Galileo TX

Olvassa el alább 📖 a magyar nyelvű használati útmutatót LumenRadio CRMX Galileo TX (2 oldal) a vezérlő kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
MANUAL LUMENRADIO CRMX Galileo
Copyright © LumenRadio AB 2023, All Rights Reserved www.lumenradio.com
APPLICATION AREA
The CRMX Galileo is a wireless lighting control product. It is designed to be used
indoors, or outdoors when installed in a IP65 rated environmental enclosure.
CRMX Galileo replaces the cable in DMX-512A systems. It can be used together
with any CRMX compatible device using either CRMX Classic or CRMX
2 modes.
CRMX Galileo can also be congured to operate in W-DMX mode where it can
operate together with W-DMX compatible devices.
GENERAL
All personnel must acquaint themselves with the instructions in this leaet before
using this product. This product must not be used if damaged. For additional
documentation for CRMX Galileo, scan the QR code on this leaet, or visit
www.lumenradio.com.
WARRANTY
All warranty claims for this product shall be directed to the local distributor/reseller.
Warranty is deemed void if:
(1) The product is modied, repaired or otherwise altered unless it has been
directed by LumenRadio AB; or
(2) The serial number on the product (the QR code) has been compromised.
SYSTEM OVERVIEW
A CRMX system replaces the need to use expensive and cumbersome DMX ca-
bles. Place one Galileo TX unit in close proximity to the lighting controller and
let it wirelessly transmit the DMX and RDM data to Galileo RX units, or other
CRMX receivers – for instance built-in receivers in wireless-ready xtures from any
of LumenRadio’s partners.
DMX data can locally be daisy chained with cable between xtures that are phy-
sically close to each other.
If range needs to be extended it is possible to operate a Galileo RX unit as
a repeater (available as an optional upgrade). A repeater receives the wireless
signal and retransmits it for receivers that otherwise would be out of range. A
repeater will also output the DMX and RDM data locally on it’s data port – just like
any receiver would do.
SAFETY
Only qualied electricians or service personnel trained by LumenRadio may
perform installations with this product. Always follow local electrical code and
regulations.
If installed using a 24 VAC isolation transformer, this must be performed in accor-
dance with IEC 61558-1.
Do not use the product if the product is damaged. Only use cables within the spe-
cied conductor sizes. This product may not be connected directly to main power.
INSTALLATION
1. Verify that the product has no physical damage.
2. Clip the unit onto a DIN rail. If installed outdoors, this must be performed in a
IP65 rated environmental enclosure.
3. Mount the antenna, or of installed in an enclosure – mount the antenna
coax cable.
4. Connect the power supply in accordance with specied voltage.
5. Connect the DMX cable to the DMX interface.
6. Power on and verify that the unit is powered up correctly – Galileo units
performs a chase with white color on the three front LEDs at power-on to
make it clearly visible that it is starting up.
BOX CONTENT
1 pc. CRMX Galileo unit 1 pc. RP-SMA antenna
1 pc. 2pin terminal plug for power 1 pc. 3pin terminal plug for data
1 pc. Quick start instruction (this leaet)
SPECIFICATIONS
Power supply AC: 24 VAC +/- 10% 50/60 Hz
Power supply DC: 12-24 VDC +/- 10%
Max. power consumption: 2.5W
Self-healing fuse: Yes
Rated wire size: 0.2 – 1.5 mm2
24 – 16 AWG
IP rating: IP X0
Dimensions (W x H x D): 36.5 x 93 x 58.7 [mm]
Weight: 85 g
Antenna connector: RP-SMA
Operating temp. range: -20 to +55 °C
Storage temp. range: -30 to +80 °C
Humidity: 0 – 90% non-condensing
Frequency range: 2402 – 2480 MHz (ISM band)
Max. RF output power: 100 mW (280 mW in US)
Supported protocols: DMX-512A, RDM
Supported RF protocols (TX): CRMX, W-DMX G3 & G4S
Supported RF protocols (RX): CRMX, CRMX
2, W-DMX G3, G4,
G4S & G5
LEGAL
CRMX is a trademark of LumenRadio AB, W-DMX is a trademark of Wireless
Solution Sweden AB.
Wireless Solution Sweden AB is a fully-owned subsidiary of LumenRadio AB.
DMX-512A and RDM refers to ANSI national standards developed and maintai-
ned by ESTA, Entertainment Services and Technology Association.
This product makes use of US patents 7,432,803; 8,457,023; 9,208,680; EU
patents EP 2415317, EP 2803248, China patents CN 102369774, CN 104041189B
and others.
Version of this quick start guide: Version 2 (2023-10-17)
MANUFACTURER
LumenRadio AB LumenRadio
Johan Willins gata 6 Alfred-Herrhausen-Allee 3-5
416 64 Gothenburg DE-65760 Eschborn
Sweden Germany
www.lumenradio.com
Scan for additional
information
FCC ID: XRSTIMOMWAN301
IC ID: 8879A-TIMOMWAN301
E115504
UL62368-1
CSA C22.2 No. 62368-1
CRMX Galileo
by LumenRadio
MANUAL LUMENRADIO CRMX Galileo
Copyright © LumenRadio AB 2023, All Rights Reserved www.lumenradio.com
YOUR GALILEO UNIT
LINK SWITCH FUNCTIONS
The link switch performs the basic link and unlink functions, but combinations of
presses can perform some special functions. All functions are listed in the tables
below. In the tables below short press is <0.5 s, long press is >3 s.
BASIC FUNCTIONS
Short On transmitter: Link available receivers
On receiver: No function
On repeater: Link available receivers
Long On transmitter: Unlink all receivers
On receiver: Unlink this receiver
On repeater: Unlink all receivers, or unlink this repeater
if pressed again within 5 seconds after unlink process.
SPECIAL FUNCTIONS
The special functions are accessed by pressing the button momentarily a number
of times, followed by a long press (> 3 s).
2 x short + long Enable/disable BLE.
3 x short + long Galileo TX: Select RF protocol.
5 x short + long Galileo RX: Enable/disable repeater (if option is installed)
7 x short + long Reset BLE PIN code.
STATUS LEDS
MODE SIGNAL (TX)
Transmitter Transmitting
Receiver Linking receivers
Repeater Unlinking receivers
BLE enabled
BLE connected SIGNAL (RX)
> 70%
30 – 70%
DATA < 30%
DMX data No link
RDM activity Not linked
IDENTIFY
When connecting via BLE using the CRMX Tooolbox app, or when using RDM, it
is possible to identify a device to know what device is accessed. When doing this,
all LEDs will ash rapidly.
LINKING
To be able to transmit data through the system, receivers needs to be linked to
the appropriate transmitter, or repeater.
1. Make sure the receivers are unlinked and that they are withing communica-
tion range.
2. If receiver is already linked, follow the steps in the unlink section.
3. Press the link switch momentarily on the transmitter.
4. Wait for the linking process to nish.
UNLINKING
Unlinking can be done directly from the transmitter, which will unlink all currently
powered receivers that are within range that is linked to this transmitter. This is
done by holding the link switch for >3 s.
Unlinking can also be done on one specic receiver by holding its link switch
pressed for >3 s.
USING REPEATERS
When the range needs to be expanded, a receiver can be upgraded to
repeaters (software license required). Before a repeater can be linked to receivers
it rst need to be linked to a transmitter.
To unlink a repeater from a transmitter, its receivers rst needs to be unlinked. Re-
peating the unlink step within 5 seconds after the unlinking process has nished
will unlink the repeater from its transmitter.
RDM (REMOTE DEVICE MANAGEMENT)
Galileo supports RDM both as transmitter and receiver (including repeater mode).
This enables conguration of RDM capable xtures, allowing DMX start address
and DMX personality to be set among other things. It also allows for monitoring
the system, such as detecting if devices goes ofine, monitor receivers’ signal
levels, and much more.
Available RDM functions varies depending on the controller and the xtures.
A Galileo TX incorporates an RDM Proxy that needs to be enabled before any
downstream devices can be discovered. This can be done either by changing the
DMX personality of the transmitter, via the link switch button, or from the CRMX
Toolbox app.
BLUETOOTH
Bluetooth, or BLE, is enabled by default. It is recommended to disable the BLE
interface after installation has been completed, or to protect the BLE interface
by setting a PIN code.
It is possible to send DMX data to the Galileo device via BLE. There are several
apps that supports this that can be downloaded from App Store. When sending
DMX data to a receiver or a repeater, the DMX data is only forwarded to the local
DMX interface. But when DMX data is sent via BLE to a transmitter device, the
DMX data will be sent to the entire network.
DMX via BLE is limited in performance due to the limitations of BLE, and is not
suitable for fast effects.
FIRMWARE UPDATES
The software in your Galileo device, called rmware, is continuously improved
and new functions may be added. It is therefore recommended to make sure you
keep the devices up to date. In all cases, make sure you have the latest rmware
installed before commissioning a new system.
Firmware can be updated via Bluetooth using the CRMX Toolbox
2 app. The latest
rmware is automatically downloaded from LumenRadio’s cloud and pushed to
your device when you initiate an update.
INSTALLING REPEATER OPTION
Galileo RX units can have an optional repeater option installed. It is installed
using the CRMX Toolbox app and requires you to have an account registered
through the app. To purchase this option, reach out to your local reseller.
CRMX TOOLBOX2
CRMX Toolbox2 is an app available from LumenRadio to congure CRMX de-
vices. It is available for iOS and Android and can be downloaded directly from
Apple App Store or Google Play Store.
Power in
Status LEDs
DMX port
Antenna connector
Link switch
- +
Gnd D- D+

Termékspecifikációk

Márka: LumenRadio
Kategória: vezérlő
Modell: CRMX Galileo TX

Szüksége van segítségre?

Ha segítségre van szüksége LumenRadio CRMX Galileo TX, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók vezérlő LumenRadio

LumenRadio

LumenRadio CRMX Outdoor RX Útmutató

30 Augusztus 2024
LumenRadio

LumenRadio CRMX Outdoor Flex Útmutató

30 Augusztus 2024
LumenRadio

LumenRadio CRMX Stardust Útmutató

30 Augusztus 2024
LumenRadio

LumenRadio MoonLite Útmutató

30 Augusztus 2024
LumenRadio

LumenRadio CRMX Slim TX Útmutató

30 Augusztus 2024
LumenRadio

LumenRadio CRMX Luna Útmutató

30 Augusztus 2024
LumenRadio

LumenRadio CRMX Aurora Útmutató

30 Augusztus 2024
LumenRadio

LumenRadio CRMX Slim RX RDM Útmutató

30 Augusztus 2024
LumenRadio

LumenRadio CRMX Galileo TX Útmutató

30 Augusztus 2024

Útmutatók vezérlő

Legújabb útmutatók vezérlő

GVM

GVM YK22 Útmutató

11 December 2024
IVT

IVT MPPTplus+ 20A Útmutató

11 December 2024
IVT

IVT SCDplus Útmutató

11 December 2024
Alfatron

Alfatron ALF-IPCON-HDMI Útmutató

10 December 2024
Hotone

Hotone Ampero Control Útmutató

8 December 2024
Hotone

Hotone Patch Kommander Útmutató

8 December 2024
IFM

IFM AC1317 Útmutató

6 December 2024
PCE Instruments

PCE Instruments PCE-RE100P Útmutató

16 Október 2024
PCE Instruments

PCE Instruments PCE-RE21R Útmutató

16 Október 2024
Thrustmaster

Thrustmaster Ferrari GT Experience Útmutató

13 Október 2024