Használati útmutató Lectrosonics DNT16i

Lectrosonics processzor DNT16i

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Lectrosonics DNT16i (20 oldal) a processzor kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/20
DNT Series
DNT16i/DNT0212 Network Processors
INSTALLATION AND STARTUP GUIDE
Rio Rancho, NM, USA
www.lectrosonics.com
Fill in for your records:
Serial Number:
Purchase Date:
A trademark of Audinate Pty Ltd.
DNT Digital Processor
LECTROSONICS, INC.
2
Installation and Quick Start Guide
Rio Rancho, NM 3
Table of Contents
FCC Part 15 Compliance 3 .......................................................
Important
Safety Instructions 4 .........................................................
Overview 5 .................................................................................
What is Dante? 5 ....................................................................
About the DNT Processors 5 ..................................................
Switched and Redundant Modes 5 .........................................
DNT16i Front Panel 6 ................................................................
DNT16i Rear Panel 6 .................................................................
DNT0212 Front Panel 7 .............................................................
DNT0212 Rear Panel 7 ..............................................................
DNT Control Panel Software 8 .................................................
DNT Software Installation 8 .....................................................
About Dante Software 9 ...........................................................
DanteTM Software
Installation 9 ......................................................................
Mandatory Settings 10 .............................................................
Dante Controller Software - Network Settings 10 ...................
DNT Control Panel Software - Signal Flow Configuration 11 ..
DNT Software - USB Connection 11 .......................................
DNT Software - Ethernet Connection 11 ................................
Hardware Connections 12 .......................................................
Installing the chassis into a rack 12 ........................................
Connecting via USB for the First Time 12 ...............................
Setup and Control Port Connections 12 .................................
Programmable Inputs 13 .........................................................
RS-232 Serial Port Wiring 13 ..................................................
Crestron® RS-232 Port Wiring 13 ............................................
Programmable Outputs 13 ......................................................
Network and PC Connections 14 ............................................
Signal Routing 15 .....................................................................
Replacement Parts and Accessories 16 .................................
Service and Repair 17 ..............................................................
Returning Units for Repair 17 .................................................
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. The equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
Changes or modifications to this equipment not expressly approved by Lectrosonics, Inc. could
void the user’s authority to operate it.

Termékspecifikációk

Márka: Lectrosonics
Kategória: processzor
Modell: DNT16i

Szüksége van segítségre?

Ha segítségre van szüksége Lectrosonics DNT16i, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók processzor Lectrosonics

Lectrosonics

Lectrosonics DNT16i Útmutató

3 Szeptember 2024
Lectrosonics

Lectrosonics DNTBOB88 Útmutató

31 Augusztus 2024
Lectrosonics

Lectrosonics DNT0212 Útmutató

31 Augusztus 2024

Útmutatók processzor

Legújabb útmutatók processzor

Atlas Sound

Atlas Sound IPS-VPS Útmutató

3 Április 2025
Noise Engineering

Noise Engineering Sono Abitus Útmutató

19 Március 2025
Alto

Alto DI1 Útmutató

16 Január 2025
Alto

Alto DI4 Útmutató

16 Január 2025
Alto

Alto HPA6 Útmutató

16 Január 2025
Alto

Alto MAXI-Q PC Útmutató

16 Január 2025
Alto

Alto VOICE plus D Útmutató

16 Január 2025
Alto

Alto MP8 Útmutató

16 Január 2025
Alto

Alto MP8D Útmutató

16 Január 2025
Alto

Alto Terminator II Útmutató

16 Január 2025