Használati útmutató Lanzar HTG889

Lanzar Vevő HTG889

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Lanzar HTG889 (18 oldal) a Vevő kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/18
3
4
5
7
9
14
14
15
www.Lanzar.com
2
INTRODUCTION
LANZAR ampliers provide high-performance sound reinforcement for your
mobile audio equipment. Its versatility enables compatibility with optional
Equalizers, Frequency Dividing Crossover Networks, and other audio processors
in a customized system. The Multi-Mode bridging capabilities allow exibility in
hosting several dierent speaker congurations.
To achieve optimum performance, it is highly recommended that you read this
Owners Manual before beginning installation.
WARNING
High powered audio systems in a vehicle are capable of generating "Live Concert
high levels of sound pressure. Continued exposure to excessively high volume
sound levels may cause hearing loss or damage. Also, operation of a motor vehicle
while listening to audio equipment at high volume levels may impair your ability
to hear external sounds such as; horns,warning signals, or emergency vehicles,
thus contributing to a potential trac hazard. In the interest of safety, LANZAR
recommends listening at lower volume levels while driving.
TABLE OF CONTENTS
PLANNING YOUR SYSTEM
WIRING CONNECTION
PANEL LAYOUT
CONTROL FUNCTIONS
SPEAKER DIAGRAMS MONO CHANNEL
TROUBLESHOOTING GUIDE
WARNINGS
SPECIFICATION
www.Lanzar.com
3
PLANNING YOUR SYSTEM
Before beginning the installation, consider the following:
1. Do you plan to add additional mobile electronics equipment in the future?
If you plan to expand your system by adding other components sometime in
the future, ensure adequate space is left and cooling requirements are met.
2. Should you use high or low level inputs?
Your Amplier has been designed to accept Low-Level (Pre-Amp outputs from
your radio) source signal. If your radio/source is equipped with Pre-Amp outputs,
it is possible to utilize them to drive the Amplier and the 2 front speakers.
Then, use the built-in power of your radio to drive the 2 rear speakers.
3. Are your components matched?
The RMS power rating of your speaker(s) must be equal or greater than the
RMS power rating of your amplier. Your speaker(s) also must be 2- 8 Ohms
impedance for stable amplier operation. Impedance information is normally
printed on the speaker basket or magnet.
4. Where will the amplier be installed?
Consider both the length of your leads, and routing when determining the
mounting location. It is best to run power and RCA wiring on opposite sides of
the vehicle to prevent induced noise. Pre-amp input jacks require a length of
high quality shielded male to male RCA patch cord.
CONNECTINGTHE POWER
CAUTION
AS A PRECAUTION, DISCONNECTTHE POWER WIRE FROM THE BATTERY WHILE
MAKING THE POWER AND GROUND CONNECTIONS TO THE AMPLIFIER.
4/8 GAUGE (Thicker if planning for additional Ampliers) wire is recommended
for both the power and ground wires 12 Gauge, for the remote turn-on wire 16
Gauge. Both types are available at most Mobile Audio Dealers or Installation
Shop.

Termékspecifikációk

Márka: Lanzar
Kategória: Vevő
Modell: HTG889

Szüksége van segítségre?

Ha segítségre van szüksége Lanzar HTG889, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Vevő Lanzar

Lanzar

Lanzar HTG889 Útmutató

12 Január 2025
Lanzar

Lanzar HTG668BT Útmutató

14 Augusztus 2024
Lanzar

Lanzar HTG888 Útmutató

14 Augusztus 2024
Lanzar

Lanzar HTG258BT Útmutató

14 Augusztus 2024
Lanzar

Lanzar HTG669BT Útmutató

13 Augusztus 2024
Lanzar

Lanzar VCT-2010 Útmutató

13 Augusztus 2024
Lanzar

Lanzar HTG138 Útmutató

12 Augusztus 2024
Lanzar

Lanzar HTG237 Útmutató

12 Augusztus 2024
Lanzar

Lanzar HTG157 Útmutató

12 Augusztus 2024
Lanzar

Lanzar VCT2410 Útmutató

11 Augusztus 2024

Útmutatók Vevő

Legújabb útmutatók Vevő