Használati útmutató Klipsch SLX

Klipsch hangszóró SLX

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Klipsch SLX (4 oldal) a hangszóró kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/4
SYNERGY SERIES
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wider blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. tripod, bracket, or table specified by the manufacturer, or soldUSE only with a cart, stand,
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. UNPLUG this a tus during lightning storms or when unused for long periods of time.ppara
14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the a tus, tus has been exposed toppara the appara
rain or moisture, does not operate normally, or has been dropped.
This symbol indicates that there are important operating and maintenance instructions
in the litera ying this unit.ture accompan
This symbol indicates that dangerous voltage constituting a risk of electric shock is
present within this unit.
WARNING: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain
or moisture.
WARNING: Voltages in this equipment are hazardous to life. No user-serviceable parts inside.
Refer all servicing to qualified service personnel.
CAUTION: Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate this device.
ABOUT YOUR KLIPSCH PURCHASE
Thank you for your purchase of Klipsch speakers.After reading this manual and connecting your
system, you will hear the result of over 55 years of stringent engineering and class-leading
research and development. Like all Klipsch products, your speakers feature Klipsch Horn-loaded
Technology—the guiding design for the first Klipschorn®developed in 1946 and for every
product tha t has followed. Horn-loading allows your speakers to deliver high sensitivity, low
distortion,f lat frequency response and wide dispersion, which translates to unequaled power,
detail and dynamics, the hallmarks of “The Klipsch Sound.” Please be sure to fill out the
included Warranty card or register online at www.klipsch.com so we are better able to serve
you. Again, thank you for choosing Klipsch and we hope that your speakers bring life to your
music and movies for many years.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
GRILLE
The speaker can be used with or without its grille in place. The grille attaches magnetically;
you can remove the grille easily by pulling it forward and replace it simply by lining up its
edges with the those of the speaker cabinet.
The logo badge on the grille can be removed, rotated 90 degrees and replaced for proper ori-
entation when using the SLX in a horizontal position. To remove the logo badge, simply push
the two pins on the rear of the logo badge together and push it out of its location on the grille.
To reinsert it, align the two pins with the hole in the grille and push the logo badge into place
(making sure the orientation of the logo badge is correct).
PLACEMENT
Your Synergy SLX speakers are designed for maximum flexibility and will perform well in a
wide variety of configurations. Figure 1 shows a typical home theater setup, with a center-
channel speaker (Synergy SLX) mounted below (or above) a flat panel tv, left and right front
speakers (Synergy SLX) flanking the screen, and another pair of speakers (Synergy SLX) to the
sides of the listening area for the main surrounds. Below are specific placement recommenda-
tions for each function.
Center-Channel Speaker: Center the speaker directly above or below your tv and mount it on
the wall (see wall mounting instructions). When using the supplied mounting bracket, each
Synergy SLX can be rotated 30° (15° in each direction) to obtain optimal directivity toward the
listening area.
Front Left and Right Speakers: The front left and right speakers should be approximately in
line with your tv and equidistant from it. The distance from the tv is not critical, though wide
separation will tend to make the sound more spacious. Avoid having either speaker closer than
2 feet to a side wall. Place them at seated ear height if that is practical. When using the
supplied mounting bracket, each Synergy SLX can be rotated 30° (15° in each direction) to
obtain optimal directivity toward the listening area.
Left and Right Surround Speakers: Using Synergy SLX’s as surround speakers ensures an
acoustic and cosmetic match to the front left, right and center speakers. The best location for
speakers employed as surround speakers is on or against the walls to the sides of the seating
area, anywhere from adjacent to the listening position to about 20º behind it. Mount them
above the ear height of seated listeners (5’-7’ high) but avoid placing them up against or on
the ceiling. Aim them straight across the room or back slightly toward the rear wall for a more
diffuse sound or toward the listening position for a more direct sound. The design of the
Synergy SLX allows great flexibility and good results can be achieved with configurations that
depart significantly from the ideal. When using the supplied mounting bracket, each Synergy
SLX can be rotated 30° (15° in each direction).
Surround Back Speakers: If your electronics support Dolby Digital EX, THX Surround EX, or
DTS-ES 7.1 or 6.1-channel surround, you can place one or two speakers behind the seating
area to serve as surround back speakers. As with the left and right surrounds, the optimum
location is a bove seated ear level. If you are using just one back surround speaker, it should be
centered behind the listening area; if you are using two, they should be spaced fairly close
together. With this type of system, the regular left and right surrounds should be located
adjacent to the seating area rather than behind it
S
C
FLAT
PANEL
TV
Optional
sub
L R
Figure 1
ENGLISH
ENGLISH
8. Once the SLX is mounted, its angle can be fine tuned to obtain optimal directivity toward the
listening area.
CAUTION: DO NOT REMOVE THE MAGNETS ON THE REAR OF THE SPEAKER ENCLOSURE.
CAUTION: SYNERGY SLX SPEAKERS ARE NOT INTENDED FOR CEILING MOUNTING.
CONNECTIONS
Note: Proper connection of your speakers to your amplifier or receiver is vital to obtaining good
sound quality. Please follow these directions carefully. Sloppy connections can cause amplifier
malfunction or damage.
Klipsch Synergy SLX speakers are wired internally with multiple gauges of high-purity copper wire,
carefully selected and wound to ensure optimum signal transfer at all frequencies. You will obtain
best performance from your speakers if you connect them to your amplifier or receiver with similar
quality wire available from your dealer. We recommend tha vier (lowert you use 18-gauge or hea -
gauge) stranded copper wire. Use a lower gauge (heavier) wire for longer runs to reduce the
amount of amplifier power lost due to the wire’s resistance.
BUT FIRST: TYPES OF CONNECTORS
Bare wire — Pull the two conductors apart for about an inch and strip approximately
1/4"
of
insula tion from the end of each. (A wire stripper will simplify this, but you can use an ordinary
pocket knife to cut around and through the insulation down to the wire.) Twist the strands of wire
on each individual conductor tightly together. Loosen the nuts on a pair of binding posts until the
holes through the metal posts are exposed, then insert the bare wire through the holes. Screw the
nuts down finger-tight on the wire. Make sure that no strands of wire are touching from one
binding post to the other or to any strands from the other conductor. Failure to observe this
precaution at either end of the connection can result in amplifier malfunction or damage.
Pins — Many pre-made speaker cables are terminated with metal pins. Loosen the nuts on a
pair of binding posts until the holes through the metal posts are exposed, then insert the pins
through the holes. Screw the nuts down finger-tight on the pins — do not over-tighten. Make
sure that there is no metal-to-metal contact between the two pins or binding posts. Failure to
observe this precaution at either end of the connection can result in amplifier malfunction
or damage.
Spade lugs — Some speaker cables are terminated with U-shaped connectors called spade
lugs. Loosen the nuts on a pair of binding posts and slip the spade lugs around the metal posts.
Screw the nuts down finger-tight on the lugs and inspect to ensure they have remained firmly
in place. Make sure that there is no metal-to-metal contact between the two lugs or binding
posts. Failure to observe this precaution at either end of the connection can result in amplifier
malfunction or damage.
OTHER TYPES OF SPECIALTY CONNECTORS ARE AVAILABLE TO FACILITATE HOOKING UP YOUR
SPEAKERS. PLEASE CONSULT YOUR AUTHORIZED KLIPSCH DEALER FOR SUGGESTIONS AND
FURTHER DETAILS.
WALL MOUNTING
Each Synergy SLX speaker can be mounted vertically or horizontally. When mounted vertically, the
wall bracket can be aligned with a wall stud (in which case the supplied drywall anchors will not be
used) or simply attached to drywall (in which case the supplied dry wall anchors will be used). When
mounting the bracket horizontally, one of the two pairs of mounting holes shown in Figure 2 to be
16" apart (holes 1 and 5 or holes 2 and 6) can be aligned with wall studs that are sixteen inches
apart. Either of the two pairs can be used. Dry wall anchors and screws should then be used in the
remaining four attachment locations. If you do not wish to mount the bracket to wall studs, all six
drywall anchors and screws must be used to attach the bracket to the wall.
To install the Synergy SLX, follow these instructions:
1. Position the mounting bracket on the wall in the desired loca tion (vertical tion and orienta
or horizontal).
2. Using the mounting bracket as a template, mark the six screw locations taking care to notice the
location of wall studs. (Wall studs can be used, if desired, as stated above. However, it is not
necessary to attach the SLX bracket to wall studs.) If used in the center channel position, make
sure that the bracket is level.
3. Remove the mounting bracket and install the necessary number of supplied drywall anchors into
the wall. (Drywall anchors are not necessary in the locations where the screw will attach to a
wall stud.)
4. Route speaker wire through the mounting bracket. Wire routing channels are incorporated into
the rear of the mounting bracket. Wire can enter at any side of the bracket and will exit in the
center of the bracket directly behind the connections on the rear of the SLX as shown
in Figure 3.
5. Place the mounting bracket in the desired location and attach it to the wall by driving the
supplied screws through the bracket’s mounting holes and into the drywall anchors or wall
stud(s), making sure not to overtighten the screws.
6. Connect the speaker wire to the SLX's binding posts. See "Speaker to Amplifier: Keeping it
Straight" for speaker wiring information.
7. Attach the SLX to the mounting bracket by seating the SLX's mounting slots, located on
each end of the back of the SLX, onto the mounting tabs of the bracket as shown in Figure 4.
The tabs will "click" into place when the connection is made. Lightly pull forward on the SLX to
make sure a solid connection has been made. To remove the SLX from the mounting bracket,
depress both buttons at each end of the back of the SLX and pull the speaker off of the mounting
bracket. The SLX should slide off easily . DO NOT force it. Make sure both buttons are depressed.
16"
16"
1
2
3 4
5
6
Figure 2
MOUNTING
SLOTS
WALL
BRACKETS
Figure 4
From Amplifier
From Amplifier
Figure 3

Termékspecifikációk

Márka: Klipsch
Kategória: hangszóró
Modell: SLX

Szüksége van segítségre?

Ha segítségre van szüksége Klipsch SLX, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hangszóró Klipsch

Klipsch

Klipsch PIC-450-T Útmutató

15 Január 2025
Klipsch

Klipsch Synergy C-2 Útmutató

15 Január 2025
Klipsch

Klipsch Synergy F-2 Útmutató

15 Január 2025
Klipsch

Klipsch Synergy F-3 Útmutató

15 Január 2025
Klipsch

Klipsch Synergy C-3 Útmutató

15 Január 2025
Klipsch

Klipsch PIC-525-T Útmutató

15 Január 2025
Klipsch

Klipsch PIC-650-T Útmutató

15 Január 2025
Klipsch

Klipsch R-2650-C Útmutató

15 Január 2025
Klipsch

Klipsch R-2650-CSM Útmutató

15 Január 2025
Klipsch

Klipsch Reference RB-15 Útmutató

15 Január 2025

Útmutatók hangszóró

Legújabb útmutatók hangszóró

Celly

Celly Ultraboost Útmutató

1 Április 2025
Muse

Muse MC-50 WI Útmutató

1 Április 2025
QSC

QSC MD-FP152-124r Útmutató

30 Március 2025
QSC

QSC PL-CA6 Útmutató

30 Március 2025
QSC

QSC PL-SUB15 Útmutató

30 Március 2025
QSC

QSC PL-SUB10 Útmutató

30 Március 2025
QSC

QSC MD-FP152-64r Útmutató

30 Március 2025
QSC

QSC PL-SUB12 Útmutató

30 Március 2025
Audac

Audac ARCHI210 Útmutató

30 Március 2025
Audac

Audac ARCHI10 Útmutató

30 Március 2025