Használati útmutató Kicker SubStage SSON12

Kicker mélynyomó SubStage SSON12

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Kicker SubStage SSON12 (10 oldal) a mélynyomó kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/10
1
SSON12
Designed for 2012 and newer Chevrolet® Sonic vehicles
©2012 Stillwater Designs
SSON12-A2-20121010
2
Subwoofer Assembly
Subwoofer
Power Harness
25A Fuse
Wire Ties x6
Foam Strip
Wire Taps x2
Adapter Harness
Subwoofer Body
Harness
3
Power Wire Routing
1. Disconnect the negative battery cable from the battery.
2. Using a razor knife make a cross shaped incision in the large rubber grommet from inside the vehicle and
feed the power wire from the engine compartment to the cabin. Using a fi sh tape wire is recommended.
Fig. 1
NOTE: If you are installing the optional amplifi er system, install the power wire for it at this time.
3. Pull the wire(s) through the grommet until the sheathing touches the grommet.
4. Remove the fuse box cover under the hood. Remove the fuse from the fuse holder on the subwoofer
power wire and connect the power wire to the accessory lug. Torque to 9 +/- 1.5 Nm. Make sure that the
wires exit on the side closest to the battery. Fig. 2
5. Install the connecter on the end of the power harness inside the cabin. The black connecter should have
a block out plug installed in one side to prevent the power wire from being inserted into the wrong position in
the connecter.
NOTE: If you are installing the optional amplifi er system, it does not matter what order the three wires are
installed on the three-pin connecter, but the terminals can only be inserted one way. If the terminal will not
go into the connecter, simply turn it 180 degrees and try again. Push the terminals in until they click and lock
into place.
Body Harness Routing
6. Remove the driver’s side kick/threshold panel by loosening the
retainer at the top and then pulling loose. Fig. 3
7. Remove the lower portion of the rear seat by pulling straight up
on the front edge.
8. Snap loose the rear drivers side threshold panel located along
the bottom of the door opening.
9. Snap loose the lower portion of the B pillar post cover.
Cut grommet here.
Fig. 1
Fig. 2
Wires should exit in
direction of arrow
Retainer – Rotate
counter-clockwise
Fig. 3
Remember to place your warranty card in the glove box for future use.

Termékspecifikációk

Márka: Kicker
Kategória: mélynyomó
Modell: SubStage SSON12

Szüksége van segítségre?

Ha segítségre van szüksége Kicker SubStage SSON12, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók mélynyomó Kicker

Kicker

Kicker 51MWF104 Útmutató

14 Január 2025
Kicker

Kicker 51MWF124 Útmutató

14 Január 2025
Kicker

Kicker 48CWR154 Útmutató

12 Január 2025
Kicker

Kicker 51MWE104 Útmutató

10 Január 2025
Kicker

Kicker 51MWE124 Útmutató

10 Január 2025
Kicker

Kicker 51CWQ102 Útmutató

24 Szeptember 2024
Kicker

Kicker 51CWQ122 Útmutató

24 Szeptember 2024
Kicker

Kicker 43C84 Útmutató

24 Szeptember 2024

Útmutatók mélynyomó

Legújabb útmutatók mélynyomó