Használati útmutató Kicker DS65.2

Kicker hangszóró DS65.2

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Kicker DS65.2 (12 oldal) a hangszóró kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/12
DS
DS SYSTEMCOMPONENT
DS DS DS600.2, 650.2, 680.2
©2007 Stillwater Designs
2007 DS Components Multilingual a01.qxp 11/12/2008 3:47 PM Page 1
Your DS components were specially designed for “Livin’ Loud” out in the harsh automotive
environment. They are made of advanced materials and construction techniques to
maintain optimal performance for years to come.
Application
The Kicker DS component systems are specifically designed for mounting in free-air
applications. The speakers do not require a sealed enclosure for optimum performance. It is
important to isolate the sound coming off the front of the driver from the sound radiating
from the back of the driver. This isolation is usually accomplished by using the driver in a
factory speaker location, or in a location with a semi-isolated rear chamber. See Figure 1.
Location
The sound produced by the DS components is directional, particularly for the tweeter’s
sonic output. The external crossover has a High Frequency Output Attenuation switch
(0, 3 & 6dB) that allows for added flexibility in positioning the tweeter. Find the best location
for stereophonic sound. If necessary, add more DS component systems to the audio
system to help distribute and balance the sound. After determining the best mounting
locations, carefully check the areas where the mounting hardware will be placed.
See Figure 2.
INSTALLATION
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Authorized Kicker Dealer:
Purchase Date:
Speaker Model Number:
_________________________
_________________________
_________________________
Note: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.
To get the best performance from your new Kicker speakers, we recommend using genuine Kicker Accessories and Wiring.
Please allow two weeks of break-in time for the speaker to reach optimum performance.
2
INSTALLATION
DSComponentSystem
Owner’sManual
DS DS DS600.2 /650.2 /680.2
Models:
WooferMounting
If you are replacing factory speakers in their original locations, you may have to enlarge the
speaker cut-outs and pre-drill new screw holes using a 7/64” (2.5mm) bit. Custom mounting
locations will require more preparation and work. In either case, make sure the speaker will
not interfere with the trunk and door opening and closing mechanisms, and the enclosed
screws will not puncture the fuel tank, wiring, or interfere with any other mechanical parts on
the underside of the mounting surface. Cycle the windows all the way down and up.
If the speaker cut-out locations require you to cut metal, avoid structural metal and braces.
If the door body and panel cannot support the weight of the speaker, an optional reinforcing
panel (thin piece of wood or Medium Density Fiberboard) may be sandwiched between the
panels. Mount the speaker to the vehicle as outlined in Figure 2.
If factory speaker wiring is not available in your desired location, it may be necessary to run
the supplied wire through the door jamb. The speaker wire should be kept away from sharp
edges and avoid the possibility of getting pinched by the door. An existing grommet in the
door jamb is the ideal place to run the speaker wire. If the factory hole and grommet do not
exist or are inaccessible, you must drill a hole
to run the speaker wire through the door jam.
Be careful not to drill into other wiring or
exiting door mechanisms. Any time a wire is
run through a hole, it is necessary to insert a
rubber or plastic grommet to protect the wire
from damage as outlined in Figure 3.
If the supplied hardware is not applicable to
your installation, some other means of
securely attaching the speakers to the vehicle
must be used.
F uig re 1
DSCOMPONENTSYSTEM
R ear Seat
Tr n S a eu k / Storage p c R dear Soun
W va es
F o dr nt Soun
W va es
F u ig re 2
D roo Panel
P c p k h dla e S ea er Grille er ov t e Mi range/Woofer
Dri er an nt wit en sev d mou h t eh c old Screws
D roo Body R ceinfor ing Panel
(Optional)
M di range/Woofer
Dri erv
Speaker rille G
Screws
Stagger les ht e ho for
t e ah wiring an sed u
r rubber o plastic
grommet to pr totec
t e r ah wire f om d mage
S t tpeaker cu -ou
S t tpeaker cu -ou
F uig re 3
F o r nt Door Body
F o hr nt Das
Kick Panel
Speaker
cu -out t
To speaker terminals
To t eh
external
c or ss erov
3
DS nent Dri er Compo v
2007 DS Components Multilingual a01.qxp 11/12/2008 3:47 PM Page 2
DS600.2
6 (160)
3/4 (20)
Titanium
4 (3)
120 (60)
90
35-21k
4 13/16 (12.3)
1 7/8 (4.8)
2 3/16 (5.5)
1 9/16 (4)
12, 4000
12, 4000
0, 3 & 6
Yes
4 5
DSCOMPONENTSYSTEM
INSTALLATION
TweeterMounting
The tweeter can be mounted one of three ways: flush, angled-surface and angled mounting.
For flush mounting applications, please refer to the illustration in Figure 5. Choose a flat
location on the panel with space behind the panel to allow room for the mounting nut. After
checking the clearances, cut a 1 9/16” (4cm) diameter mounting hole in the panel. Place the
shorter mounting nut behind the panel (only use the longer mounting nut if panel thickness
prohibits the use of the shorter mounting nut). Feed the wire through the optional tweeter
flange, the hole in the panel and the mounting nut. Mount the tweeter by screwing the
mounting nut onto the tweeter.
For angled-surface mounting applications use the angled-surface mount cup as a template
and pre-drill one 7/64” (2.5mm) screw hole for attaching the angled-mounting cup to the
panel, and a 5/16” (8mm) hole for the wires. A M3 pan-cross head wood screw is supplied
to attach the mounting cup to the panel. Position the tweeter over the attached angled-
mounting cup and press it into position. See Figure 6.
For angled mounting applications choose a flat location on the panel with space behind the
panel to allow room for the mounting nut and back angle ring. After checking the
clearances, cut a 1 9/16” (4cm) diameter mounting hole in the panel. Place the front angle
ring (does not fit through the longer tweeter mounting nut) in front of the panel. Then place
the wire and tweeter through the tweeter flange, front angle ring and into the panel. Next
place the wire through the back angle ring (fits through the longer tweeter mounting nut),
place the back angle ring over the rear of the tweeter, and line-up the narrow part of the
front angle ring for the preferred angle of operation. Place the wire through the longer
tweeter mounting nut and loosely tighten the mounting nut around the tweeter. Rotate all the
parts in unison until the tweeter is angled in the desired direction. Secure the assembly by
tightening the tweeter mounting nut. See Figure 7.
Wiring
Hooking up the Kicker DS-Series Component Speakers is easy. Mount the external
crossover in a location free and clear of water and mechanical components of the vehicle
with the enclosed phillips-head wood screws. The positive and negative leads on the
speakers are terminated with connectors of different shapes and sizes that intuitively
connect to the external crossover’s connectors. After connecting the speakers to the
external crossover, connect the external crossover to the source unit or amplifier in
accordance with its owner’s manual. For reference, the Gray wire is Positive and the Black
wire is Negative on the external crossover.
Wiring SpeakersMultiple
Modern high performance component system speakers have a lower DC Resistance than
what used to be available. The Kicker DS-Series component system speakers are rated at
four ohms and work with any source unit or amplifier designed to operate at a four ohm
load. If you want to use two DS-Series component system speakers (two midrange/woofers
and two tweeters) on each channel of
your source unit or amplifier wire the
speakers in series, as shown below. This
will improve the sound quality, lower the
total harmonic distortion and lessen the
thermal load at the source unit or
amplifier. This may prevent an amplifier
from shutting down, due to over-current
protection circuitry. See Figure 4.
DS680.2
6x8 (160x200)
3/4 (20)
Titanium
4 (3)
90 (45)
90
40-21k
5x7 3/16 (12.7x18.3)
2 3/8 (6)
2 3/4 (7)
1 9/16 (4)
12, 4000
12, 4000
0, 3 & 6
No
Performance
Model:
Woofer Size, in (mm)
Tweeter Size, in (mm)
Dome Material
Rated Impedance, ohm (DC Resistance, ohm)
Power Handling Watts, Peak (RMS)
Sensitivity [SPLo], dB @ 1W, 1m
Effective Frequency Range, Hz
Woofer Mounting Hole Diameter, in (cm)
Woofer Top Mount Depth, in (cm)
Woofer Bottom Mount Depth, in (cm)
Flush Mounting Tweeter Hole Diameter, in (cm)
High Pass, dB, at Frequency, Hz
Low Pass, dB, at Frequency, Hz
High Frequency Output Attenuation, dB
Bolt-Thru Grilles
F uig re 5
DS650.2
6.5 (165)
3/4 (20)
Titanium
4 (3)
120 (60)
90
35-21k
5 1/2 (14)
1 13/16 (4.6)
2 (5.1)
1 9/16 (4)
12, 4000
12, 4000
0, 3 & 6
Yes
F ul sh Mount
A u f cngled-S r a e Mount
Angle ntd Mou
S thorter Mounting Nu
A u f cngled-S r a e Mou Cupnt
Longer Mounting Nut
Back Angle Ring
F or nt Angle ing R
Panel
Panel
Panel
Optional Tweeter lange F
Tweeter
Tweeter
Tweeter lange F
Tweeter
S r eou c Unit li ier or Amp f
High Frequency Output
A u o tten ati n Switch: 0, 3 & 6dB
Two DS-Series Component
S tpeakers wire ind series o
a single annel ch
Ex ovternal Cross er
PERFORMANCE
F uig re 4
F uig re 6
F u ig re 7
M3 Screw
2007 DS Components Multilingual a01.qxp 11/12/2008 3:47 PM Page 3

Termékspecifikációk

Márka: Kicker
Kategória: hangszóró
Modell: DS65.2

Szüksége van segítségre?

Ha segítségre van szüksége Kicker DS65.2, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hangszóró Kicker

Kicker

Kicker 51MSS8 Útmutató

10 Január 2025
Kicker

Kicker 51MSS65 Útmutató

10 Január 2025
Kicker

Kicker Q-Class 41QSS674 Útmutató

30 December 2025
Kicker

Kicker Q-Class 41QSS654 Útmutató

30 December 2025
Kicker

Kicker Premium 51MSC8 Útmutató

19 December 2024
Kicker

Kicker Premium 51MSC65 Útmutató

19 December 2024
Kicker

Kicker PS44 Útmutató

2 Október 2024
Kicker

Kicker KSC35 Útmutató

27 Szeptember 2024
Kicker

Kicker 51KM614FL Útmutató

24 Szeptember 2024
Kicker

Kicker 51KMTCXL65 Útmutató

24 Szeptember 2024

Útmutatók hangszóró

Legújabb útmutatók hangszóró

Celly

Celly Ultraboost Útmutató

1 Április 2025
Muse

Muse MC-50 WI Útmutató

1 Április 2025
QSC

QSC MD-FP152-124r Útmutató

30 Március 2025
QSC

QSC PL-CA6 Útmutató

30 Március 2025
QSC

QSC PL-SUB15 Útmutató

30 Március 2025
QSC

QSC PL-SUB10 Útmutató

30 Március 2025
QSC

QSC MD-FP152-64r Útmutató

30 Március 2025
QSC

QSC PL-SUB12 Útmutató

30 Március 2025
Audac

Audac ARCHI210 Útmutató

30 Március 2025
Audac

Audac ARCHI10 Útmutató

30 Március 2025