Használati útmutató Jindara Barossa
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Jindara Barossa (8 oldal) a Heater kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/8
1. Subject to clauses 2 & 3 of this warranty, A.F. Gason Pty Ltd ACN 004 667 556 (Gason) warrants the following components of its heaters against defects in workmanship and/or materials for the
following periods from the date of purchase:
(a) the firebox for ten years;
(b) the paint finish for a period of twelve months if the purchaser has followed the instructions provided by Gason in this Operation and Installation Instructions manual; and
(c) all other components for twelve months except the glass, fire brick lining or baffle plate if, in the opinion of Gason, these items have been damaged by impact.
2. This extended warranty does not apply:
(a) if the heater is purchased from a person who has not been authorised by Gason to sell its products;
(b) if, in the opinion of Gason, the heater or any component has been subjected to abuse, misuse, alteration, modification or has not been installed, operated or maintained in accordance with the
instructions provided by Gason; or
(c) to owners other than the original purchaser.
3. If you believe that the heater you purchased contains a manufacturing defect and you wish to make a claim under this warranty, please contact an authorised Gason service centre to arrange for an
assessment.
4. If, after assessing the heater, Gason determines that the heater contains a manufacturing fault, Gason may at its discretion:
(a) replace the heater;
(b) repair or replace specific components of the heater; or
(c) provide a full refund.
5. Parts replaced under this warranty are warranted for the balance of their original warranty period.
6. If, at the discretion of Gason, the heater or any part needs to be replaced, serviced or repaired at an authorised Gason service centre, then the person claiming under this warranty must pay all costs
associated with:
(a) returning the heater; and
(b) the delivery or collection of any new or repaired heater.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Any benefits you receive under these warranties are in addition to other rights and remedies that you may have as a consumer under a law in relation to the heater to which these warranties relate.
These warranties are given by:
A.F. Gason Pty Ltd
Blake Street
Ararat VIC 3322
Please contact us if you have any queries on:
Phone: 03 5352 2151;
or email us via the “Contact Us” section of our website: www.gason.com.au.
A.F. Gason Pty Ltd reserves the right to modify or alter specifications, materials, etc. in the interest of product improvement.
WARRANTY
Barossa SRS3 Insert
16
GPN 231079
Barossa SRS3 Insert
Operation & Installation Instructions
REV.A
Please keep these instructions for future reference.
WOODHEATING
Barossa SRS3 Insert
15
THIS PAGE INTENTIONALLY LEFT BLANK
Barossa SRS3 Insert
2
!
WARNING
Read and follow these instructions carefully before installing and using this appliance.
SAVE THESE INSTRUCTIONS
Paint curing and care
!
WARNING
• A flue fire with resulting damage may occur if this appliance is not installed, operated and
maintained as per this booklet.
• Never place combustible material such as wood, paper or furniture near the appliance.
• This appliance is designed to burn dry wood. Do not burn rubbish, driftwood, flammable
liquids or any substance containing salts or corrosives.
• This appliance must not be installed and operated in an area where kerosene, petrol, paint
thinner or other flammable liquid is used or stored.
• The flue system must be inspected and cleaned annually or sooner if required. Failure to
do so could result in an excessive build up of creosote which may result in a flue fire
which may damage the flue or cause damage to your home.
• The surface of the appliance becomes hot during operation. Do not touch the surface of
this appliance. Keep children away from the appliance during operation. Do not allow
anyone to operate this appliance who is not familiar with the instructions in this booklet.
!
WARNING
Your heater is coated with the best available heat resistant paint. Even though the paint has
been baked after application, it may require further temperature curing. It may, if you overfire
the heater on its first fire, discolour. For your first two or three firings, never exceed medium
air setting and always have the fan on when above low burn. Do not wipe the heater while the
paint is curing. After the paint has cured the only maintenance required to maintain the
heaters finish is to wipe it with a soft cloth. Do not use any commercial cleaners or solvents
on the paint finish.
We are proud of the presentation of our products. If at any time you need to freshen up the
paint finish, your local dealer has touch up paint available for purchase.
If you have any enquires, please contact the dealer from whom you purchased your heater:
PLEASE COMPLETE:
Dealer Name
Dealer Address
Phone
Please attach your original purchase dockets to this booklet for future reference.
Safety Warnings
Barossa SRS3 Insert
3
Installation
!
WARNING
This heater is to be installed into a masonry fireplace or a Jindara ZCV Clearance cabinet.
THE INSTALLATION OF THIS APPLIANCE MUST BE CARRIED OUT AS PER THIS MANUAL AND
THE FLUE MANUFACTURERS SPECIFICATIONS.
WE RECOMMEND THAT YOU USE A QUALIFIED INSTALLER TO CARRY OUT THE
INSTALLATION.
If you have any other enquiries, please contact the dealer from whom you purchased your
heater.
THIS APPLIANCE WEIGHS IN EXCESS OF 120 KILOGRAMS. EXTREME CARE SHOULD BE TAKEN
WHEN HANDLING THE APPLIANCE.
Installation
All dimensions used in this document are in millimetres and are minimum unless otherwise
stated. Under no circumstances can these dimensions be reduced.
A.F. Gason Pty Ltd accepts no liability whatsoever for any interpretation of AS/NZS
2918:2001
Installation Permit
Depending on your local authority requirements, a permit may be required for the
installation of your heater. It is your responsibility to arrange the same.
Installation into existing or masonry fireplace
The Jindara Barossa SRS3 Insert can be installed into a masonry fireplace with a flue
system that is in accordance with the relevant sections of AS/NZS 2198:2001. No
combustible or heat sensitive material may be placed closer than 1340mm from the top of
the hearth/base of appliance and 50mm either side of the appliance’s fascia.
Minimum hearth depth of 510mm from the front of the fascia panel must be achieved. If it
is desired to reduce the hearth depth to the minimum allowable 300mm in front of
appliance fascia, the appliance must be raised to a new height - refer elevated installation
instructions on page 7.
For detailed mantle clearance dimensions, refer to Figure 4.
Brick removal
!
WARNING
IF BRICKS REQUIRE REMOVAL WHEN PREPARING THE FIREPLACE, ENSURE THAT YOU DO NOT
EXPOSE COMBUSTIBLE MATERIALS BEHIND THE BRICKWORK OR WEAKEN THE INTEGRAL
STRUCTURE OF THE CHIMNEY.
Section showing Installation
Figure 1. Masonry Installation
Barossa SRS3 Insert
14
• Smoke entering the room from the firebox when the door is open may be caused by
• Insufficient length of flue (Flue to be 4500mm minimum from underneath base of heater to underside of cowl)
– Increase height of flue.
• Flue Downdraught
– Consult dealer or increase height of flue.
• Creosote Build up in flue
– Remove cowl and clean flue as per cleaning instructions. Check moisture content of wood.
• Excessive ash build up
Some woods will give large amounts of ash despite how you run the heater. Others will give you very little. Use the wood which is most
convenient for you as long as it is dry. After a period of time you will get to know when to empty your unit. Bark will give you excessive
ash. Try not to burn it.
If you are burning wood that gives you charcoal, you may find that after running the heater say for 8 hours at maximum burn rate, the
charcoal builds up excessively. Overnight burn will reduce this charcoal back to a fine ash. If you are not ready to shutdown for
overnight burn when you next fuel the stove, load the stove with only one piece of wood and lay it across the firebox on top of the
charcoal. Open the air control wide open and you will find the charcoal will burn down with the one piece of wood. Repeat the process
until the ash level is significantly reduced.
Troubleshooting (Continued)
Termékspecifikációk
Márka: | Jindara |
Kategória: | Heater |
Modell: | Barossa |
Szüksége van segítségre?
Ha segítségre van szüksége Jindara Barossa, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Heater Jindara
17 Augusztus 2024
13 Augusztus 2024
8 Augusztus 2024
7 Augusztus 2024
6 Augusztus 2024
4 Augusztus 2024
Útmutatók Heater
- Heater Mestic
- Heater Electrolux
- Heater Nedis
- Heater Parkside
- Heater Candy
- Heater Philips
- Heater Gorenje
- Heater Adler
- Heater Princess
- Heater SilverCrest
- Heater Bosch
- Heater NewAir
- Heater MPM
- Heater AEG
- Heater Emerio
- Heater Einhell
- Heater Bartscher
- Heater Maxwell
- Heater Hyundai
- Heater Scarlett
- Heater Tefal
- Heater HQ
- Heater Emos
- Heater Corbero
- Heater Camry
- Heater Xiaomi
- Heater Danby
- Heater DeLonghi
- Heater Heinner
- Heater Infiniton
- Heater Sunbeam
- Heater Beurer
- Heater Trumatic
- Heater Wilfa
- Heater Klarstein
- Heater VOX
- Heater Scheppach
- Heater Vivax
- Heater Conceptronic
- Heater Thomson
- Heater Fagor
- Heater Unold
- Heater SHX
- Heater Brentwood
- Heater Ardes
- Heater Cuisinart
- Heater Eden
- Heater Eurolite
- Heater Jocel
- Heater Bimar
- Heater Clatronic
- Heater Bomann
- Heater Bauknecht
- Heater Dyson
- Heater Ambiano
- Heater Cecotec
- Heater Sencor
- Heater Pelgrim
- Heater Qlima
- Heater Baxi
- Heater Innoliving
- Heater Rowenta
- Heater Güde
- Heater Izzy
- Heater JANDY
- Heater GoldAir
- Heater Domo
- Heater Russell Hobbs
- Heater Caso
- Heater Carson
- Heater Create
- Heater Mora
- Heater Black & Decker
- Heater Enders
- Heater Orbegozo
- Heater Livoo
- Heater Eberle
- Heater ARGO
- Heater Guzzanti
- Heater Concept
- Heater DCS
- Heater DEDRA
- Heater SVAN
- Heater Nobo
- Heater TriStar
- Heater Suntec
- Heater BaseTech
- Heater RYOBI
- Heater Fantini Cosmi
- Heater Chauvet
- Heater Midea
- Heater Steba
- Heater Heller
- Heater Kogan
- Heater Honeywell
- Heater Broan
- Heater Mesko
- Heater Velleman
- Heater Dimplex
- Heater Master
- Heater Kenmore
- Heater Thermex
- Heater Hayward
- Heater Tesy
- Heater Trotec
- Heater Blaupunkt
- Heater AstralPool
- Heater Korona
- Heater Stadler Form
- Heater Taurus
- Heater Signature
- Heater AFK
- Heater Everdure
- Heater DeWalt
- Heater Kalorik
- Heater Waldbeck
- Heater Alpina
- Heater Philco
- Heater Brandson
- Heater ECG
- Heater Stanley
- Heater Rotel
- Heater Vemer
- Heater Ufesa
- Heater Vonroc
- Heater Rinnai
- Heater Cotech
- Heater Argoclima
- Heater Ausclimate
- Heater WAGAN
- Heater Beper
- Heater Bestron
- Heater Orion
- Heater Soler & Palau
- Heater SereneLife
- Heater Ravanson
- Heater Haeger
- Heater Olimpia Splendid
- Heater Orava
- Heater Eurom
- Heater Mill
- Heater Maestro
- Heater Eureka
- Heater Sogo
- Heater Sonnenkönig
- Heater Fluval
- Heater Lifesmart
- Heater Flama
- Heater Tectro
- Heater Fenix
- Heater Zibro
- Heater Quigg
- Heater Calor
- Heater Sinbo
- Heater Swan
- Heater Anslut
- Heater EWT
- Heater Mellerware
- Heater Nestor Martin
- Heater Termozeta
- Heater Eldom
- Heater Cresta
- Heater Bionaire
- Heater Maginon
- Heater Otsein-Hoover
- Heater Profile
- Heater Ferroli
- Heater Real Flame
- Heater Evolar
- Heater Perel
- Heater Zibro Kamin
- Heater Proline
- Heater Royal Sovereign
- Heater King
- Heater Piazzetta
- Heater Heylo
- Heater Kent
- Heater Arnold Rak
- Heater Wamsler
- Heater Duux
- Heater Imetec
- Heater Alpatec
- Heater Blaze
- Heater Primo
- Heater Creda
- Heater Plieger
- Heater Reer
- Heater Zehnder
- Heater Essentiel B
- Heater Prime3
- Heater Blumfeldt
- Heater CaterChef
- Heater Kambrook
- Heater Zephir
- Heater Harvia
- Heater Brixton
- Heater Superior
- Heater Kunft
- Heater La Nordica
- Heater Jotul
- Heater Vasco
- Heater Noveen
- Heater Nectre
- Heater Cadel
- Heater Grunkel
- Heater Jaga
- Heater Masport
- Heater REMKO
- Heater Extraflame
- Heater Lynx
- Heater Just Fire
- Heater Optimum
- Heater Hartig And Helling
- Heater Gutfels
- Heater Westfalia
- Heater Veito
- Heater Ecoteck
- Heater Etherma
- Heater Nordic Fire
- Heater Haas+Sohn
- Heater Wanders
- Heater Grandhall
- Heater Emga
- Heater Heatstrip
- Heater Escea
- Heater Braemar
- Heater Bromic Heating
- Heater Martec
- Heater Hatco
- Heater SunRed
- Heater Aerian
- Heater IXL
- Heater XPower
- Heater True North
- Heater WestBend
- Heater Hortus
- Heater Prem-i-air
- Heater Quadra-Fire
- Heater VIESTA
- Heater Apricus
- Heater Brivis
- Heater Hubbell
- Heater HeatStar
- Heater Pacific Energy
- Heater Dri Eaz
- Heater Regency
- Heater Burley
- Heater Kaden
- Heater Jarden
- Heater Noirot
- Heater Ouellet
- Heater Wulfe
- Heater Duro Pro
- Heater Herschel
- Heater HyCell
- Heater TURBRO
- Heater Radialight
- Heater Rowi
- Heater Neopower
- Heater Arlec
- Heater Guardian
- Heater Big Ass Fans
- Heater Pureheat
- Heater EvoHeat
- Heater Bromic
- Heater MSW
- Heater Solamagic
- Heater Contura
- Heater Mirpol
- Heater Alkari
- Heater Longvie
- Heater Blue Rhino
- Heater Rheem
- Heater Gasmate
- Heater Ionmax
- Heater Airo
- Heater Mission Air
- Heater Omega Altise
- Heater Scandia
- Heater Vasner
- Heater Fire Sense
- Heater InfraNomic
- Heater Heat Storm
- Heater Excelair
- Heater Heatscope
- Heater Heat1
- Heater Thermotec
- Heater Perfect Aire
- Heater AustWood
- Heater Uniprodo
Legújabb útmutatók Heater
16 Október 2024
15 Október 2024
15 Október 2024
15 Október 2024
15 Október 2024
15 Október 2024
15 Október 2024
15 Október 2024
15 Október 2024
15 Október 2024