Használati útmutató JBL Northridge N28II

JBL hangszóró Northridge N28II

Olvassa el alább 📖 a magyar nyelvű használati útmutatót JBL Northridge N28II (4 oldal) a hangszóró kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

SPEAKER PLACEMENT

Proper placement of the

speakers is an important step

in obtaining the most realistic

soundstage possible. These

recommendations are for the

optimum placement of the

loudspeakers. Use these

placement recommendations as

a guide. Slight variations will

not diminish your listening

pleasure. Aim the tweeter of

each loudspeaker toward the

listening position at about ear-

level height for best imaging,

especially in digital surround

systems.

All of the Northridge Series

loudspeakers referred to in this

guide are video-shielded and

can safely be placed near a

television.

MODELS: N36II, N38II, ND310II

MODELS: N26II, N28II

As Front Speakers As Surround Speakers

N26II, N28II, N36II,

N38II, ND310II

NORTHRIDGE™ SERIES

SPEAKERS

OWNER’S GUIDE

5 – 6 ft.

SPEAKER CONNECTIONS

These models are shipped with

four self-adhesive nonskid pads

that are to be used when the

loudspeaker is intended to be

placed on a smooth-surfaced

floor, such as tile or hardwood.

Gently lay the speaker on its side

(not its front or back) on a soft,

nonabrasive surface. Attach each

pad to the bottom of its foot in the

widest portion of the recessed

area.

DO NOT attach the pads if

the speaker will be placed

on carpeting.

NEVER drag the speaker to move

it, as this will damage the pads,

the feet and/or the wood cabinet

itself. Always lift the speaker and

carry it to its new location.

CAUTION: Floorstanding (tower)

loudspeakers have a high center

of gravity and may become

unstable and tip over during

earthquakes or if rocked, tipped

or improperly positioned. If this is

a concern, these speakers should

be anchored to the wall behind

them, using the same procedures

and hardware customary for

anchoring bookcases and wall

units. Customer is responsible for

proper installation and proper

selection of hardware.

Without pad With pad

The supplied self-adhesive felt

pads may be attached to the

bottom corners of your speakers

to protect your furniture.

MODELS: N26II, N28II MODELS: N36II, N38II, ND310II

CONNECTION TIPS

Speakers and electronics

terminals have corresponding (+)

and (–) terminals. It is important

to connect both speakers

identically: (+) on the speaker to

(+) on the amplifier and (–) on the

speaker to (–) on the amplifier.

Wiring “out of phase” results in

thin sound, weak bass and a poor

stereo image. With the advent of

multichannel surround sound

systems, connecting all of the

speakers in your system with the

correct polarity remains equally

important in order to preserve

the proper ambience and

directionality of the program

material. To use the binding-post

speaker terminals, unscrew the

colored collar until the pass-

through hole in the center post is

visible under the collar. Insert the

bare end of the wire through this

hole; then screw the collar down

until the connection is tight. The

hole in the center of each collar

is intended for use with banana-

type connectors.

To comply with European CE

certification, these holes are

blocked with plastic inserts at the

point of manufacture. To use

banana-type connectors requires

the removal of the inserts. Do not

remove these inserts if you are

using the product in an area

covered by the European CE

certification.

– +– +

– +

Receiver’s Speaker Outputs

LEFT

RIGHT

– +

If there is no sound from any of

the speakers:

• Check that receiver/amplifier is

on and that a source is playing.

• Review proper operation of your

receiver/amplifier.

If there is no sound coming from

one speaker:

• Check the “Balance” control on

your receiver/ amplifier.

• Check all wires and connections

between receiver/amplifier and

speakers.

• Make sure no wires are

touching other wires or terminals

and creating a short circuit.

• Make sure all wires are

connected. Make sure none of

the speaker wires are frayed, cut

or punctured.

• In Dolby* Digital or DTS®

modes, make sure that the

receiver/processor is configured

so that the speaker in question is

enabled.

• Turn off all electronics and

switch the speaker in question

with one of the other speakers

that is working correctly. Turn

everything back on, and determine

whether the problem is in the

same place, i.e., the speaker that

was working previously now has

no sound and the speaker that

was not working now sounds

fine; or whether it has moved, i.e.,

the speaker that was not working

still has no sound and the

speaker that was working is still

fine. If the problem is in the same

place, the source of the problem

is most likely with your receiver

or amplifier, and

you should

consult the owner’s manual for that

product for further information.

the problem has followed the

speaker, consult your dealer for

further assistance or, if that

is not possible, visit our Web site

at www.jbl.com for further

information.

If the system plays at low

volumes but shuts off as volume

is increased:

• Check all wires and connections

between receiver/amplifier

and speakers.

• Make sure all wires are

connected. Make sure none of

the speaker wires are frayed, cut

or punctured.

• If more than one pair of main

speakers is being used, check

the minimum impedance

requirements of your

receiver/amplifier.

If there is no (or low) bass

output:

• Make sure the polarities

(+ and –) of the left and right

“Speaker Inputs” are connected

properly.

• Consider adding a powered

subwoofer to your system for use

with digital “.1” surround formats.

If there is no sound from the

surround speakers:

• Check all wires and

connections between receiver/

amplifier and speakers. Make

sure all wires are connected.

Make sure none of the speaker

wires are frayed, cut or

punctured.

• Review proper operation of your

receiver/amplifier and its

surround sound features.

• Make sure the movie or TV

show you are watching is

recorded in a surround sound

mode. If it is not, check to see if

your receiver/amplifier has other

surround modes you may use.

•

In Dolby Digital or DTS modes,

make sure your receiver/

processor is configured so that the

surround speakers are enabled.

• Review the operation of your

DVD player and the jacket of your

DVD to make sure that the DVD

features the desired Dolby Digital

or DTS mode, and that you have

properly selected that mode

using both the DVD player’s menu

and the DVD disc’s menu.

TROUBLESHOOTING

Declaration of Conformity

We, Harman Consumer International

2, route de Tours

72500 Chateau-du-Loir

France

declare in own responsibility that the products

described in this owner’s manual are in compliance

with technical standards:

EN 61000-6-3:2001

EN 61000-6-1:2001

Gary Mardell

Harman Consumer International

Chateau-du-Loir, France 4/04

Termékspecifikációk

Márka:	JBL
Kategória:	hangszóró
Modell:	Northridge N28II

Szüksége van segítségre?

Ha segítségre van szüksége JBL Northridge N28II, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók hangszóró JBL

29 Március 2025

12 Január 2025

12 Január 2025

12 Január 2025

JBL Tower X Marine MT10HLW Útmutató

6 Január 2025

JBL Control CM42AW Útmutató

1 Január 2025

JBL Performance P36AW Útmutató

1 Január 2025

JBL Balboa 30 Útmutató

1 Január 2025

JBL 250Ti Útmutató

1 Január 2025

JBL 800 Útmutató

1 Január 2025

Útmutatók hangszóró

Legújabb útmutatók hangszóró

QSC MD-FP152-124r Útmutató

30 Március 2025

QSC PL-CA6 Útmutató

30 Március 2025

QSC PL-SUB15 Útmutató

30 Március 2025

QSC PL-SUB10 Útmutató

30 Március 2025

QSC MD-FP152-64r Útmutató

30 Március 2025

QSC PL-SUB12 Útmutató

30 Március 2025

Audac ARCHI210 Útmutató

30 Március 2025

Audac ARCHI10 Útmutató

30 Március 2025

Prixton Jaia Útmutató

30 Március 2025

Prixton Jaia Max Útmutató

30 Március 2025