Használati útmutató JBL BassPro II

JBL mélynyomó BassPro II

Olvassa el alább 📖 a magyar nyelvű használati útmutatót JBL BassPro II (8 oldal) a mélynyomó kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/8
THANK YOU
for choosing the JBL BassPro™II.
BassPro II has been designed to
deliver great bass performance from
a compact, easily installed powered
subwoofer enclosure.
To get the best performance from your
BassPro II, we strongly recommend
that installation be entrusted to a
qualified professional. Although these
instructions explain how to install
BassPro II in a general sense, they
do not show specific installation
methods that may be required for your
particular vehicle. If you do not have
the necessary tools or experience, do
not attempt the installation yourself.
Instead, please ask your authorized
JBL car audio dealer about pro-
fessional installation.
In order that we may better serve you
should you require warranty service,
please retain your original sales
receipt and register your BassPro II
online at www.jbl.com.
INSTALLATION
WARNING: Playing loud music in
an automobile can hinder your ability
to hear traffic and permanently dam-
age your hearing. We recommend
listening at low or moderate levels
while driving your car. JBL accepts
no liability for hearing loss, bodily
injury or property damage resulting
from the use or misuse of this product.
INSTALLATION
WARNINGS AND TIPS:
• Always wear protective eyewear
when using tools.
• Disconnect the vehicle’s negative (–)
battery terminal before starting the
installation.
• Check clearances on both sides of
a planned mounting surface. Be
sure that screws or wires will not
puncture brake lines, fuel lines or
wiring harnesses, and that wire
routing will not interfere with the safe
operation of the vehicle.
• When making electrical connections,
make sure they are secure and
properly insulated.
• If BassProII’s fuse must be replaced,
be sure to use the same type of fuse
and current rating as that of the
original.
CHOOSING A MOUNTING
LOCATION FOR
BASSPRO II:
Choose a mounting location that
doesn’t interfere with cargo, the fold-
down rear seat or the trunk lid. The
best location is usually a corner of
the trunk or cargo area, as shown
in Figures 1 and 2.
Securely mount BassProII to the
mounting surface using the four
enclosed self-tapping screws.
Choose a mounting location in the
front of the vehicle for the remote
level control.
Figure 1. Figure 2.
Figure 3. Bottom view of BassProII.
2
INSTALLING THE REMOTE CONNECTING THE SUBWOOFER
LEVEL CONTROL TO BASSPRO II
The Subwoofer Level Control may be
mounted under the dash or dismantled
and mounted in the dash for a factory-
installed appearance.
UNDER-DASH MOUNTING
Select a mounting location that allows
easy access to the control while driv-
ing. Using the Subwoofer Level Control
as a template, mark and drill holes in
the mounting surface. Attach the
Subwoofer Level Control using the
mounting screws provided (Figure 4).
IN-DASH MOUNTING
Disassemble the Subwoofer Level
Control by removing the two Phillips-
head screws on the front panel,
rear panel and on top. Remove the
Subwoofer Level Control’s bottom and
side panels. Slide the Subwoofer Level
Control’s PC board forward to release
the RJ11 connector from the back
panel and remove the board along with
the potentiometer, knob and connector
as a single assembly.
Choose a mounting location that
allows easy access to the control,
and provides 1-3/4" clearance behind
the mounting surface. Drill a 9/32"
hole in the mounting surface. Feed
the Subwoofer Level Control’s
potentiometer shaft (with the knob
removed) through the hole and use the
nut and washer provided to hold the
control in place (Figure 5).
Route the cable behind the dash or
other interior panels and under the
carpet. Do not route the cable outside
the vehicle. Connect the RJ11 cable
between the RJ11 receptacle on the
BassProII and the receptacle on the
Subwoofer Level Control (Figure 6).
Socket
for
Control
Cable
Level
Control
Circuit
Board
Washer
Hex Nut
Knob
Figure 4. Under-dash mounting of the
Subwoofer Level Control.
Figure 5. In-dash mounting of the Subwoofer Level Control.
Figure 6. Subwoofer Level Control electrical
connection.
Knob
Hex Nut
Washer Level-
Control
Circuit
Board
Socket
for
Control
Cable
BassProII Connection Panel
Control
Cable
Rear View of
Level-Control
Circuit Board
3

Termékspecifikációk

Márka: JBL
Kategória: mélynyomó
Modell: BassPro II

Szüksége van segítségre?

Ha segítségre van szüksége JBL BassPro II, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók mélynyomó JBL

JBL

JBL ARC SUB Útmutató

1 Január 2025
JBL

JBL SSW-4 Útmutató

27 December 2024
JBL

JBL SSW-2 Útmutató

27 December 2024
JBL

JBL 800.4GTi Útmutató

26 December 2024
JBL

JBL ARC SUB10 Útmutató

26 December 2024
JBL

JBL Cinema Sound CSS10 Útmutató

26 December 2024
JBL

JBL Grand Touring GTO1212BP Útmutató

26 December 2024
JBL

JBL Grand Touring GTO1214BR Útmutató

26 December 2024
JBL

JBL Cinema Vision CVSUB50 Útmutató

26 December 2024
JBL

JBL Decade DS100 Útmutató

26 December 2024

Útmutatók mélynyomó

Legújabb útmutatók mélynyomó

Phase Technology

Phase Technology IW200-II Útmutató

4 Április 2025
Wet Sounds

Wet Sounds ZERO 10 S4 XZ-W Útmutató

2 Április 2025
SoundTube

SoundTube CM1001D Útmutató

2 Április 2025
JL Audio

JL Audio FS108-W5 Útmutató

31 Március 2025
Phase Technology

Phase Technology PL-12p Útmutató

30 Március 2025
ETON

ETON Graphit 8-2 Útmutató

19 Március 2025
ETON

ETON Graphit 8-4 Útmutató

19 Március 2025
ETON

ETON Graphit 10-4 Útmutató

19 Március 2025
ETON

ETON MW 10 FLAT Útmutató

19 Március 2025
ETON

ETON PW 8 Útmutató

19 Március 2025