Használati útmutató Intermatic ET2145C

Intermatic nincs kategorizálva ET2145C

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Intermatic ET2145C (8 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/8

Electronic 4-Circuit

24-Hour Time Switch

Installation and Setup Instructions

With 100-Hour Backup

Federal Communications Commission (FCC) Notice for ET2000 Series Time Switches

Description

This document explains the setup and conguration of the Intermatic ET2145

4-Circuit Electronic 24-Hour Time Switch. The ET2145 time switch automatically

switches loads according to the entered 24-hour schedule. The time switch can

support up to 48 xed ON and 48 xed OFF events (96 total). Each xed event can

be applied to any combination of circuits and days.

The time switch features an LCD and panel-mounted control buttons to set,

review, and monitor the time switch functions, including setting date and time,

schedule creation, enabling or disabling Daylight Saving Time (DST) and

conguring DST switchover dates.

Follow these instructions to complete the installation and programming of the

ET2145 time switch.

This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must accept any interference, including interference that may cause

undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and radiates radio frequency energy and, if

not installed and used in accordance with instructions, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference that requires the user to correct at his or her own expense.

MODELS ET2145C, ET2145CR, ET2145CP

Shown in indoor/outdoor

lockable metal enclosure

NOTICE

• Do NOT touch circuit board components, contact can create a static discharge, which can damage these electronic components.

• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.

• More than one circuit breaker or disconnect switch may be required to de-energize the equipment before servicing.

• For plastic enclosures, bonding between conduit connections is not automatic and must be provided as part of the installation.

• Installation and/or wiring must be in accordance with National and Local Electrical Code requirements.

• Use #14-#8 AWG wires, rated at least 105°C - COPPER conductors ONLY.

• If the power disconnect point is out of sight, lock it in the OFF position and tag it to prevent unexpected application power.

• Make sure there is no wire insulation under the terminal plate on the time switch connector. Firmly tighten terminal screws.

• For outdoor locations or wet locations (rain-tight), conduit hubs that comply with requirements of the UL514B (standard for fitting conduit and

outlet boxes) are to be used.

• Do not remove insulator that is covering terminals.

• Do NOT exceed maximum current carrying capacity.

• KEEP DOOR CLOSED AT ALL TIMES when not servicing.

Risk of Fire or Electric Shock

WARNING

Latch location Tilt top forward

Installation

Follow these instructions to install the time switch.

1. Open the time switch enclosure door.

2. Remove and retain the screw that secures the plastic insulator.

3. Lift the left side of the plastic insulator and pivot away to expose the terminal strip.

4. Press the latch at the top of the enclosure and pull out the mechanism from the

enclosure.

5. Choose and remove the selected knockout(s) from the enclosure.

NOTE: There are ve 1/2 inch to 3/4 inch combination knockouts available. There are

two on the bottom of the enclosure, one on each side, and one on the rear. If a 3/4

inch knockout is needed, remove the 1/2 inch knockout rst, then the 3/4 knockout.

6. Place the enclosure in the desired location providing space for the enclosure door to

swing open fully.

7. Securely mount enclosure using provided mounting holes.

8. Use appropriately rated ttings for the installation.

9. Snap the mechanism back into the enclosure.

10. Strip 1/2 inch off the supply and load wires. Use AWG #14-#8 copper conductors

rated at least 105ºC. Torque to 15.6 lbf-in.

11. Connect the wires to the proper terminals on the time switch and tighten the screws

rmly (See wiring diagrams).

12. Connect ground wire to grounding terminal at the bottom of metal enclosures.

13. Return the insulator to its original position and replace the screw.

14. Close enclosure door.

15. Apply power to the time switch.

1/2 inch

Wiring Diagrams

OUTPUT 1

OUTPUT 2

OUTPUT 3

OUTPUT 4

OUTPUT

1&2

OUTPUT

3&4

OUTPUT 1

OUTPUT 2

OUTPUT

3&4

OUTPUT 3

OUTPUT 4

OUTPUT

1&2

OUTPUT 4

OUTPUT 3

OUTPUT

1&2

OUTPUT

1&2

OUTPUT

3&4

AC IN

NO-1 COM1 NO-2 COM2 COM3NO-3 COM4NO-4

CIRCUIT 1 CIRCUIT 2 CIRCUIT 3 CIRCUIT 4TIMER

POWER

L2/N

TIMER CONFIGURATION FOR TWO CONTACTOR CONTROLS

OUTPUT CONFIGURATION: PUL - CIRCUIT 1 AND 2

OUTPUT CONFIGURATION: PUL - CIRCUIT 3 AND 4

COM

OPEN

COM

OPEN

Termékspecifikációk

Márka:	Intermatic
Kategória:	nincs kategorizálva
Modell:	ET2145C

Szüksége van segítségre?

Ha segítségre van szüksége Intermatic ET2145C, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók nincs kategorizálva Intermatic

Intermatic ET2145C Útmutató

7 Április 2025

Intermatic ET2115C Útmutató

7 Április 2025

Intermatic ETW3CP Útmutató

7 Április 2025

Intermatic ET2105C Útmutató

7 Április 2025

Intermatic ET8115C Útmutató

7 Április 2025

Intermatic Arista ALC-IWD Útmutató

30 Március 2025

Intermatic T30404R Útmutató

17 December 2024

Intermatic PF1102T Útmutató

17 December 2024

Intermatic PRO2002403 Útmutató

17 December 2024

Intermatic NOISEFILTER Útmutató

17 December 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

Nedis NBARF4501FBK Útmutató

7 Április 2025

Soundstream BX-108Z Útmutató

7 Április 2025

Soundstream BX-12 Útmutató

7 Április 2025

Soundstream BX-23Q Útmutató

7 Április 2025

Pulsar SF116 Útmutató

7 Április 2025

Pulsar S108 Útmutató

7 Április 2025

Pulsar PSC12015 Útmutató

7 Április 2025

Soundstream BX-20Z Útmutató

7 Április 2025

ProFlo PF6731ZBN Útmutató

7 Április 2025

ProFlo PFXC1080LSCP Útmutató

7 Április 2025