Használati útmutató Illustra IPS02-B12-OI03

Illustra Térfigyelő kamera IPS02-B12-OI03

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Illustra IPS02-B12-OI03 (2 oldal) a Térfigyelő kamera kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

2. Attaching the camera to the mounting arm (continued)

B. Place the camera onto the hinge (1) (Figure 5) and release the pin so that

the camera is attached to the mounting arm plate.

Figure 5

C. See step 4 to connect the power cable and then continue on at step D.

D. Flip the camera so that it sits properly on the mounting plate and arm

secure it to the mounting arm plate th the four T10 screws (1) (Figure wi 6).

Quick Start Guide

( - -8200 1630 04_A0)

Illustra Pro Gen 3 Bullet Cameras

In the box

 4 x plastic screw anchors (use on masonry walls and wood)

 Phillips pan head tapered screw TP6x32 (use on masonry wall and wood) 4 x mm

 4 x Phillips pan head tapered screw M5x8mm (Adaptor plate base)

 Printed Quick Start Guide 1 x

 Printed regulatory document 1 x

 NTSC / PAL output female BNC cable 1 x

 1 x RJ45 Connector

 1 x Terminal block

 Mounting arm 1 x

 Mounting template 1 x

 1 x Desiccant bag

 4 Toggle screw (Expansion Bolt) x

 1 x T10 security Torx wrench

 1 x Universal electrical box mounting plate (IPSMDEBPLATE)

 1 x Pendant / pole mount adaptor

 1 x rubber plug (with two holes) and 1 rubber pin

 1 x rubber plug (with no holes)

 1 x 4mm Allen key

Installation tools

 1 x Drill

 1 x T10 security Torx wrench

 1 x Phillips screw driver

Quick reference

 Default IP: 192.168.1.168 (DHCP enabled)

 Default Username and Password: admin

Note: You can attach the camera to a surface or directly to a pendant or pole 1 ½ ‘’

Male NPT pipe using the pendant / pole mount adaptor. (The pendant / pole mount

adaptor can be attached to a standard 1 ½‘’ NTP pipe using threads or set screws).

Note: To ensure optimal lens performance, JCI recommends using the automated

lens calibration feature within the web GUI following initial camera installation.

1. Attaching the mounting arm to a surface

A. Place the mounting template provided on the surface and drill four 8mm

(0.3 inch) holes. 14

B. sert the four screw anchors into the four holes on the surface. In

C. After passing all required cabling through the mounting arm, place the

mounting arm (1) (Figure 1) on the surface and align the four holes on the

mounting arm (2) (Figure 1) with the four screw anchors or expansion bolts

on the surface (3) (Figure 1).

D. Insert the rubber plug into the top hole on the mounting arm (4) (Figure 1) to

prevent water from entering the mounting arm.

Figure 1

1. Attaching the mounting arm to a surface (continued)

E. Securely attach the mounting arm to the surface with the four TP6x32mm

screws (1) (Figure 2).

Figure 2

F. Insert the Ethernet cable through the waterproof rubber (1) (Figure 3) and if

not using both grommet holes insert the rubber pin (2) (Figure 3) into the

waterproof rubber.

G. Insert the waterproof rubber onto the mounting arm plate. (3) (Figure 3).

1. Attaching the mounting arm to a surface (continued)

Figure 3

2. Attaching the camera to the mounting arm

A. Push the pin (1) (Figure. 4) from the mounting arm hinge.

Figure 4

2. Attaching the camera to the mounting arm (continued)

Figure 6

3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe

A. Place the pendant/pole mount adaptor (1) (Figure 7) around a standard 1

½‘’ Male NPT threaded water pipe (2) (Figure 7) and securely attach the

two M3x0.5P (L = 6mm) screws on the pendant mount adaptor with the T10

security Torx wrench.

Figure 7

Table 1: Camera buttons / connections

Button / connections Description

Alarm in 1

Alarm in 2

Alarm out

COM

Audio line in

Audio line out

Ground

Analog out cable connection

Micro SD card slot

AC 24 V

AC power connection

USB cable connection

Reboot button (Hold for 10 seconds)

Reset button (Hold for 20 seconds)

RJ45 Ethernet cable connection / PoE+

3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe

(continued)

B. Unscrew the M5 Hex socket cap screw (1) (Figure 8) to remove the

mounting arm plate (2) (Figure 8) from the mounting arm (3) (Figure 8).

Figure 8

C. Push the pin (1) (Figure 9) and place the camera onto the hinge and release

the pin so that the camera is attached to the mounting arm plate.

Figure 9

3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe

(continued)

D. See step 4 to connect the power cable and then continue on at step E.

E. Securely attach the mounting arm plate to the camera with the four T10

screws (1) (Figure 10) on the mounting arm plate.

Figure 10

F. Place the mounting plate arm and camera into the pendant mount adaptor

(1) (Figure 11) and securely attach the two M3x0.5P (L = 6mm) screws with

the T10 security Torx wrench.

3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe

(continued)

Figure 11

4. Connecting the power cable to the power plugs

A. Connect the power cable to the power plugs with one of the following

options:

 AC 24V: Connect 24V cables to terminals AC 24V.

 PoE+: Connect the RJ45 jack to a PoE compatible network device

that supplies power through the Ethernet cable.

5. Adjusting the camera position

A. Use the T10 security Torx wrench to adjust the bracket Tilt angle (2) (Figure

6) and to adjust the bracket Pan angle (3) (Figure . 6)

6. Adjusting the sun shield hood

A. Move the sun shield hood (4) (Figure 6) forward and backward to adjust the

position of the sunshade.

Note: When the camera is mounted inverted to a pendant 1 ½ ‘’ NTP pipe you

must remove the sun shield hood by unscrewing the M3x0.5P (L = 8mm)

screw with the T10 security Torx wrench (3) (Figure 11) and relocate the

sun shield with screw as per the sun shield hood located in Figure 11.

CAUTION: Extending the sun shield hood forward could obstruct the eld of view

(FOV) when the camera lens is set to ‘Wide’.

7. Location of camera buttons, connections and Desiccant bag

Note: The gure below indicates the location of the camera buttons and

connections (1) (Figure 12) and Desiccant bag (2) (Figure 12) on the camera.

Figure 12

Table 2: Universal Mounting plate symbols and descriptions

Plate

Symbol

Name

Description

4S Junction

Box

Attach the plate to a North American 4 inch

square electrical box.

Octagon Box

Attach the plate to a North American octagon

electrical box.

Electrical box

(UK)

Attach the plate to a UK electrical box.

Electrical box

(EU)

Attach the plate to a European electrical box.

Warnings

1. For US and Canada use a NRTL listed power adaptor.

2. The mains power adaptor equipment should be marked LPS (Limited

Current Source) or PS2 and rated according to 50C, 24VAC, 1.27A min

or PoE IEEE802.3at type 2 Class 4, 48VDC, 0.38A min.

3. To meet security immunity requirements use an uninterruptable PSU to

supply power to the mains adaptor or POE mid/end span.

4. The cables for 24Vac, Audio and Alarms should not exceed 3m unless

additional measures are taken to reduce the eect of interference picked

up on the cables.

5. USB and Analogue Video out cables should only be used temporarily for

service and not permanently installed.

6. For outdoor use the camera should be mounted at least 3m above ground

level”

JOHNSON CONTROLS, TYCO and ILLUSTRA are trademarks and/or registered

trademarks. Unauthorized use is strictly prohibited.

Termékspecifikációk

Márka:	Illustra
Kategória:	Térfigyelő kamera
Modell:	IPS02-B12-OI03

Szüksége van segítségre?

Ha segítségre van szüksége Illustra IPS02-B12-OI03, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Térfigyelő kamera Illustra

Illustra IPS02-B15-OI03 Útmutató

19 Augusztus 2024

Illustra IES02MFBNWIYB Útmutató

19 Augusztus 2024

Illustra IPS02-B12-OI03 Útmutató

19 Augusztus 2024

Illustra IES02B1BNWIYB Útmutató

18 Augusztus 2024

Illustra IFS16-M10-BT03 Útmutató

18 Augusztus 2024

Illustra IPS05-B16-OI03 Útmutató

18 Augusztus 2024

Útmutatók Térfigyelő kamera

Legújabb útmutatók Térfigyelő kamera

Hikvision DS-2CE10DF8T-FSLN Útmutató

6 Április 2025

Hikvision DS-2CE56C0T-IRPF Útmutató

5 Április 2025

Hikvision DS-2CD2141G1 Útmutató

5 Április 2025

Dahua Technology Pro IPC-HDPW5442G-Z Útmutató

15 Január 2025

Toshiba IKS-WR7412 Útmutató

14 Január 2025

Flir FC-610 O Útmutató

13 Január 2025

AVerMedia FC1320-P Útmutató

13 Január 2025

Digitus OptiMax DN-16037 Útmutató

13 Január 2025

Hikvision DS-2CE59U1T-AVPIT3ZF Útmutató

13 Január 2025

Hikvision IDS-2CD7526G0-IZHSY Útmutató

13 Január 2025