Használati útmutató ID-Tech MiniMag

ID-Tech nincs kategorizálva MiniMag

Olvassa el alább 📖 a magyar nyelvű használati útmutatót ID-Tech MiniMag (4 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

MINIMAG

Magnetic Stripe Reader

TTL

User’s Manual

ID TECH

10721 Walker Street

Cypress, California 90630

(714) 761-6368

www.id-tech.net

80030501-005 Rev. A R02/05 #422

MINIMAG

Magnetic Stripe Reader

TTL

User’s Manual

ID TECH

10721 Walker Street

Cypress, California 90630

(714) 761-6368

www.id-tech.net

80030501-005 Rev. A R02/05 #422

Agency Approved

Speciﬁcations for subpart B of part 15 of FCC rule for a Class A computing

device.

Limited Warranty

ID TECH warrants this product to be in good working order for a period of

one year from the date of purchase. If this product is not in good working

order as warranted above, or should this product fail to be in good working

order at any time during the warranty period, repair or replacement shall be

provided by ID TECH.

This warranty does not cover incidental or consequential damages incurred

by consumer misuse, or modiﬁcation of said product. For limited warranty

service during the warranty period, please contact ID TECH to obtain an

RMA number and instructions for returning the product.

contained herein is provided to the user as a convenience. While every effort

has been made to ensure accuracy, ID TECH is not responsible for damages

that might occur because of errors or omissions, including any loss of proﬁt

or other commercial damage. The speciﬁcations described herein were cur-

rent at the time of publication, but are subject to change at any time without

prior notice.

ID TECH is a registered trademark of International Technologies & Systems

Corporation. MiniMag and Value through Innovation are trademarks of Inter-

national Technologies & Systems Corporation.

OPERATION

Make sure the reader is properly cabled and is receiving sufﬁcient power. To

read a card, slide the card, in either direction, through the reader slot, with the

magnetic stripe facing the magnetic head.

ELECTRICAL CHARACTERISTICS

DC Electrical Characteristics (25° C)

Item Symbol Min. Typical Maximum Unit Condition

Supply Voltage VCC 2.6 5.5 V

Maximum ICC 1.1 per track mA IMDL =(VCC - VOL)/10K

Active Supply + IMDL

Current

Maximum 30 per track

Sleep Current I

SLEEP + IMDH A IµMDH=(VCC - VOH

)/10K

Minimum High VCC-0.03 V IOUT =50 Aµ

Level Voltage VOH 2.3 V IOUT =3mA, VCC=2.6V

5.25 V IOUT =6mA, VCC=5.5V

Maximum Low VOL 0.1 V I

OUT =50 A µ

Level Voltage 0.22 V I

OUT =3mA, VCC=2.6V

0.2 V IOUT =6mA, VCC=5.5V

Agency Approved

Speciﬁcations for subpart B of part 15 of FCC rule for a Class A computing

device.

Limited Warranty

ID TECH warrants this product to be in good working order for a period of

one year from the date of purchase. If this product is not in good working

order as warranted above, or should this product fail to be in good working

order at any time during the warranty period, repair or replacement shall be

provided by ID TECH.

This warranty does not cover incidental or consequential damages incurred

by consumer misuse, or modiﬁcation of said product. For limited warranty

service during the warranty period, please contact ID TECH to obtain an

RMA number and instructions for returning the product.

contained herein is provided to the user as a convenience. While every effort

has been made to ensure accuracy, ID TECH is not responsible for damages

that might occur because of errors or omissions, including any loss of proﬁt

or other commercial damage. The speciﬁcations described herein were cur-

rent at the time of publication, but are subject to change at any time without

prior notice.

ID TECH is a registered trademark of International Technologies & Systems

Corporation. MiniMag and Value through Innovation are trademarks of Inter-

national Technologies & Systems Corporation.

OPERATION

Make sure the reader is properly cabled and is receiving sufﬁcient power. To

read a card, slide the card, in either direction, through the reader slot, with the

magnetic stripe facing the magnetic head.

ELECTRICAL CHARACTERISTICS

DC Electrical Characteristics (25° C)

Item Symbol Min. Typical Maximum Unit Condition

Supply Voltage VCC 2.6 5.5 V

Maximum ICC 1.1 per track mA IMDL =(VCC - VOL)/10K

Active Supply + IMDL

Current

Maximum 30 per track

Sleep Current I

SLEEP + IMDH A IµMDH=(VCC - VOH

)/10K

Minimum High VCC-0.03 V IOUT =50 Aµ

Level Voltage VOH 2.3 V IOUT =3mA, VCC=2.6V

5.25 V IOUT =6mA, VCC=5.5V

Maximum Low VOL 0.1 V I

OUT =50 A µ

Level Voltage 0.22 V I

OUT =3mA, VCC=2.6V

0.2 V IOUT =6mA, VCC=5.5V

5 2

SPECIFICATIONS

Operating

Temperature: 32° F to 131° F (0° C to 55° C).

Storage

Temperature: -22° F to 158° F (-30° C to 70° C).

Humidity: Maximum 95% non-condensing.

MTBF: Read electronics, 21,000,000 POH.

Magnetic

Head Life: 1,000,000 passes minimum.

Rail and

Cover Life: 1,000,000 passes minimum.

Read Rate: Less than one error in 100,000 bits on

cards conforming to ISO7811 1-5 (not

induced by operator error).

Swipe Speed: 3 to 60 inches per second, bi-directional.

Card Thickness: .01 to .045 inches.

Slot Width: .050 inches (1.37mm).

Dimensions: Length: 3.54 inches (90mm).

Width: 1.34 inches (34mm).

Height: 1.10 inches (28mm).

Weight: 4.6 oz.

Cable Length: 6-foot straight cable.

DATA, CLOCK AND CARD PRESENT SIG-

NALS

The following is a timing diagram of typical DATA and CLOCK signals from

ID TECH electronics:

CLOCK: The CLOCK output is narrow pulse normally high, and goes low

when data is valid. The data level is stable at both the rising and falling edges

of the CLOCK pulse. CLOCK pulse width is typically 32 microseconds.

CARD PRESENT: The CARD PRESENT signal indicates data is being read

from the media being passed through the slot. It will not switch until ﬂux

reversals (magnetic pulses) have been detected. After the ﬂux reversals have

been detected, CARD PRESENT goes low. It stays low throughout the read-

ing process and for 5 to 10 milliseconds, after the last ﬂux reversal is read.

Typically, CARD PRESENT is used to signal the start and ﬁnish of a card

read. It may also be used as an interrupt signal for alerting the ﬁrmware that

the reading operation is in process.

DATA: The DATA output level indicates the value of the bit being decoded

during a CLOCK pulse. It is a low level for ones (1) and a high level for

zeros (0). The DATA signal’s level is steady at the rising and falling edges

and during the low level of the CLOCK pulse.