Használati útmutató Hobart 6614

Hobart Fűrészgép 6614

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Hobart 6614 (12 oldal) a Fűrészgép kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/12
FORM 34527 Rev. B (August 2011)
MODEL 6614 MEAT SAW
MODEL
6614 ML-134096
PREVIOUS MODELS COVERED BY THIS MANUAL:
6614 ML-134050
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com
– 2 –
Installation, Operation, and Care of
MODEL 6614 MEAT SAW
SAVE THESE INSTRUCTIONS
GENERAL
The 6614 Meat Saw is rugged, durable, and easy to clean. The saw is equipped with a water resistant
3 HP electric motor and direct gear drive transmission that provides a blade speed of 3500 feet per minute.
The carriage (Fig. 1) has stainless steel ball bearings providing easy travel and dependability. The shaped
front edge of the carriage is comfortable to the operator's body even when leaned on during movement.
The carriage lock is standard. The upper pulley cover and bafe are stainless steel.
Table, carriage, pulleys, guides, and wiper assemblies can be quickly removed without tools for ease of
cleaning. Moving parts are enclosed but accessible. The blade is guarded above and below the cutting
zone. The pusher plate is provided to eliminate the need of handling items close to the blade; it can ride
on the right "anged-end" of the carriage so you keep your hands away from the cutting edge of the blade.
For electrical specications above 250 volts, a transformer provides a 115 volt control circuit voltage.
One long-life blade is furnished with each saw as standard equipment. This blade cannot be re-sharpened;
replacement blades are available through your local Hobart Service Ofce.
© HOBART, 1995, 2000
PL-41501-1
UPPER PULLEY COVER
COLUMN GUARD
GAUGE PL EAT
TABLE (RIGHT)
GAUGE PL E HANDLEAT
LOCK LEVER
LOWER COVER (SCRAP N)PA
LEGS
FEET
CARRIAGE LOCK
CARRIAGE
TABLE (LEFT) SAW BLADE
UPPER GUIDE AND GUARD
SWITCH KNOB
Fig. 1
– 3 –
INSTALLATION
UNPACKING AND ASSEMBLY
Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found
to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
Prior to installation, test the electrical service to make sure it agrees with the specications on the machine
data plate located on the column.
Packed in a packet attached to the table compartment are the pusher plate and the gauge plate handle.
Place the pusher plate in its storage location under the carriage support (Fig. 2). Assemble the gauge
plate handle to the gauge plate support by screwing the stud into the threaded hole (Fig. 3).
LEVELING
Place the saw in its operating location. Using a spirit level, level the meat saw front-to-back and side-to-
side by turning the threaded feet in or out.
PL-52107
Hand Knob
Upper Guide
and Guard
PL-41502-1
CARRIAGE
SUPPORT
SAW BLADE
CARRIAGE
PUSHER PL EAT
HAND KNOB
PL-41503-1
GAUGE PL E HANDLEAT
Disconnect the electrical power to the machine and follow lockout / tagout
procedures.
SAW BLADE
The saw blade must be installed so the teeth point to the right
and down (Fig. 4).
UPPER GUIDE AND GUARD ASSEMBLY
When the saw is off, the hand knob (Fig. 4) can be used to raise
or lower the upper guide and guard assembly so the cutting
zone is only as high as necessary for the piece being cut. The
hand knob is not loosened during raising or lowering — it should
remain tightly secure.
Fig. 2 Fig. 3
Fig. 4

Termékspecifikációk

Márka: Hobart
Kategória: Fűrészgép
Modell: 6614

Szüksége van segítségre?

Ha segítségre van szüksége Hobart 6614, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Fűrészgép Hobart

Hobart

Hobart 6801 Útmutató

21 Augusztus 2024
Hobart

Hobart 6614 Útmutató

21 Augusztus 2024

Útmutatók Fűrészgép

Legújabb útmutatók Fűrészgép

Bavaria By Einhell

Bavaria By Einhell BHS 66 Útmutató

3 Április 2025
Bavaria By Einhell

Bavaria By Einhell BPS 600 E Útmutató

3 Április 2025
Makita

Makita DCS4610 Útmutató

2 Április 2025
Makita

Makita DPC6430 Útmutató

1 Április 2025
Makita

Makita DCS431 Útmutató

1 Április 2025
Makita

Makita DCS430 Útmutató

1 Április 2025
Makita

Makita EK6101 Útmutató

1 Április 2025
Makita

Makita DCS6401 Útmutató

1 Április 2025
Kraftronic

Kraftronic KT-ST 550 Útmutató

30 Március 2025
Kraftronic

Kraftronic KT-US 650 Útmutató

30 Március 2025