Használati útmutató Harley Davidson J02994 (2003)
Harley Davidson
Motor
J02994 (2003)
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Harley Davidson J02994 (2003) (2 oldal) a Motor kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/2
INSTRUCTIONS
-J02994 REV. 10-10-2003
SHIFTER LINKAGE COVER
General
This “Harley-Davidson script”-style shifter-linkage cover kit
fits 1997 and later FXDWG (Dyna Wide Glide®) model motor-
cycles. This kit also fits 1993 and later Dyna models
equipped with Forward Control Kit 49080-03.
NOTE
A Service Manual for your model motorcycle is available
from any Harley-Davidson dealer.
Installation
1. See the Service Parts illustration. Obtain an upper mount-
ing bracket (2), lower mounting bracket (3), two 1/2-inch
long screws and the Allen wrench (6) from the kit.
2. See Figure 1. Assemble the upper and lower mounting
brackets onto the shaft of the ball screw shell at one
end of between the ball screw (3) andthe shifter rod (1),
the jam nut (2) so the shaft passes above the three
holes in the brackets.
Insert the two screws in the outboard holes of the lower
bracket, and use the Allen wrench to thread them part
way into the holes in the upper bracket. Do not fully
tighten the screws at this time.
3. Repeat Steps 1 and 2 at the other end of the shifter rod.
4. Position the linkage cover (1) on top of the linkage and
examine the fit.
• If the cover fits properly, proceed to Step 8.
• If the center holes in the front and rear upper mounting
brackets cannot be adjusted to line up with the holes
on the inboard side of the cover, the linkage will need
to be adjusted to accept the cover. Proceed to Step 5.
5. See Figure 1 (below) and SHIFTER LINKAGE
ADJUSTMENT in the Service Manual. To adjust the
length of the linkage, remove the link attaching nut (5)
and flat washer at the forward ball screw.
6. Loosen the jam nut (2) at the front end of the shifter rod,
and remove the mounting bracket installed in Step 3.
Rotate the forward ball screw shell to achieve the prop-
er length to allow mounting of the cover.
7. Re-attach the ball screw to the shifter lever with the flat
washer and nut removed in Step 5. Torque the nut on
the ball stud to 70-90 in-lbs (7.9-10.2 Nm).
Torque the jam nut on the shifter rod to 20-24 ft-lbs
(27.1-32.5 Nm).
8. Fasten the rear of the cover (1) to the rear upper bracket
using a short screw (5) from the kit. Fasten the front of
the cover to the front bracket with the remaining screw.
Tighten the cover securely to the upper brackets.
Position the cover upright over the shifter rod, and tight-
en the four remaining screws to clamp the brackets
securely to the ball screw shells.
9. If the linkage needed adjustment (Steps 5 through 7),
the position of the shift foot lever (6) may have
changed.
To return the lever to the original position, loosen the
socket head screw (7) holding the lever to the shaft. Pull
the lever from the shaft, rotate to the desired angle and
slide the lever back onto the shaft.
Torque the screw to 18-22 ft-lbs (24.4-29.8 Nm).
®
Kit Number 33878-04
1 of 2
Figure 1. Stock Shifter Linkage
i02475
1. Shifter rod
2. Jam nut (2)
3. Ball screw shell (2)
4. Shifter lever
5. Link attaching nut
6. Shift foot lever
7. Socket screw
2
31
4
5
2
6
3
7
-J02994 2 of 2
Service Parts
®
Shifter Linkage Cover
Date 10/03
Part No. 33878-04
Item Description (Quantity) Part No.
1 Linkage cover Not sold separately
2 Mounting bracket (upper) (2) 33879-04
3 Mounting bracket (lower) (2) 33880-04
4 Screw, button head, hex socket,
#10-24 x 1/2 in (4) 94381-92T
5 Screw, button head, hex socket,
#10-24 x 1/4 in (2) 3339
6 Allen wrench, 1/8 in Not sold separately
i02476
1
5
2
3
4
5
2
3
4
6
Termékspecifikációk
| Márka: | Harley Davidson |
| Kategória: | Motor |
| Modell: | J02994 (2003) |
Szüksége van segítségre?
Ha segítségre van szüksége Harley Davidson J02994 (2003), tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Motor Harley Davidson
29 Szeptember 2024
22 Szeptember 2024
17 Szeptember 2024
27 Augusztus 2024
20 Augusztus 2024
4 Augusztus 2024
3 Augusztus 2024
2 Augusztus 2024
31 Július 2024
30 Július 2024
Útmutatók Motor
- Motor Yamaha
- Motor Milwaukee
- Motor Husqvarna
- Motor Honda
- Motor BMW
- Motor Mercedes-Benz
- Motor Suzuki
- Motor KTM
- Motor Ducati
- Motor Mitsubishi
- Motor Reebok
- Motor Triumph
- Motor Hyosung
- Motor Kawasaki
- Motor Joy-It
- Motor Juki
- Motor Metabo
- Motor Beta
- Motor Aprilia
- Motor Texas
- Motor Kettler
- Motor Piaggio
- Motor GasGas
- Motor Danfoss
- Motor Indian
- Motor Benelli
- Motor Nautilus
- Motor Bajaj
- Motor Mash
- Motor Hero
- Motor Victory
- Motor Emco
- Motor Cagiva
- Motor Chang Jiang
- Motor Moto Guzzi
- Motor Derbi
- Motor TVS
- Motor SMC
- Motor Ridley
- Motor Sherco
- Motor Royal Enfield
- Motor Anova
- Motor Zero
- Motor MV Agusta
- Motor BodyCraft
- Motor Mahindra
- Motor CRRCpro
Legújabb útmutatók Motor
16 Január 2025
12 Január 2025
11 Január 2025
9 Január 2025
9 Január 2025
4 Január 2025
4 Január 2025
3 Január 2025
1 Január 2025
1 Január 2025