Használati útmutató Garmin VIRB Remote

Garmin távirányító VIRB Remote

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Garmin VIRB Remote (14 oldal) a távirányító kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/14
VIRB™ Remote Instructions.............................................................................................................. 2
Instructions de la télécommande VIRB™.......................................................................................... 4
VIRB™ Istruzioni del telecomando.................................................................................................... 6
VIRB™ Fernbedienung – Anweisungen............................................................................................ 8
VIRB™ Instrucciones del mando a distancia................................................................................... 10
Instruções do controlo remoto VIRB™............................................................................................ 12
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. VIRB™ and ANT+™ are trademarks of Garmin Ltd. or its subsidiaries. These
trademarks may not be used without the express permission of Garmin.
This product is ANT+™ certified. Visit for a list of compatible products and apps.www.thisisant.com/directory
July 2014 190-01627-90_0DPrinted in Taiwan
TA-2013/2179
TRA
REGISTERED No:
ER0127480/14
DEALER No:
DA0061884/11
VIRB™ Remote Instructions
Remote Overview
ÀRecord key. Select to record video on connected devices.
ÁPhoto key. Select to capture a photo on connected devices.
ÂStop key. Select to stop recording video on connected devices.
ÃStatus LED.
Status LED
LED Activity Status
Flashing green Searching for a paired device.
Alternating red and green Attempting to pair with a device.
12 rapid green flashes Successfully paired with a device.
Four rapid green flashes Successfully sent a command to a device.
Four rapid red flashes Failed to send a command to a device.
Flashing red Device is recording video.
Pairing the Remote with Your Device
The first time you connect the VIRB remote to your VIRB
device, you must pair the remote with your device.
1On the VIRB device, select > > to SETUP Remote Remote
turn on the remote control feature.
2On the VIRB remote, select any key.
The status LED starts flashing green.
3On the VIRB remote, hold two keys simultaneously until the
status LED starts alternating green and red, and release the
keys.
The remote searches for your VIRB device. When the
remote pairs successfully, the status LED flashes green 12
times.
After the remote is paired, it connects to your device whenever
the device is in range and turned on.
Using the Mounts
Several mounts are available for your remote, either included
with the product or as an optional accessory. The mounts allow
you to attach the remote to your body, your bike, or other
objects.
• Align two of the notches À with the sides of the mount, and
press the remote into the mount until it clicks.
• Press gently on the release tab Á, and lift the remote from
the mount.
Replacing the Battery
WARNING
Do not use a sharp object to remove batteries.
Keep the battery away from children.
Never put batteries in mouth. If swallowed, contact your
physician or local poison control center.
Replaceable coin cell batteries may contain perchlorate
material. Special handling may apply. See
www.dtsc.ca.gov.hazardouswaste/perchlorate.
CAUTION
Contact your local waste disposal department to properly
recycle the batteries.
Before you can replace the battery, you must have a small
Phillips screwdriver, a small flat screwdriver, and a CR2032
lithium coin-cell battery.
1Using a Phillips screwdriver, remove the three screws from
the back plate À.
2Remove the back plate from the remote.
3Wrap the end of a small flat screwdriver with tape.
The tape protects the battery, battery compartment, and
contacts from damage.
4Carefully pry the battery from the back plate.
5Install the new battery into the back plate with the positive
side facing down.
6Verify the gasket Á is fully seated in the groove.
2
7Replace the backplate, aligning the post  with the gap in
the circuit board Ã.
8Replace and tighten the three screws.
NOTE: Do not overtighten.
Specifications
Battery type User-replaceable CR2032, 3 volts
Battery life Up to 1.5 years (1 hour per day)
Operating temperature
range
From -10° to 50°C (from 14° to 122°F)
Radio frequency/protocol 2.4 GHz ANT+™ wireless communications
protocol
Water rating 5 ATM*
*The device withstands pressure equivalent to a depth of
50 meters.
3

Termékspecifikációk

Márka: Garmin
Kategória: távirányító
Modell: VIRB Remote

Szüksége van segítségre?

Ha segítségre van szüksége Garmin VIRB Remote, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók távirányító Garmin

Garmin

Garmin VIRB Remote Útmutató

14 Szeptember 2024
Garmin

Garmin GHS 20 Útmutató

25 Július 2024
Garmin

Garmin eBike Remote Útmutató

17 Július 2024
Garmin

Garmin GHS 20i Útmutató

4 Július 2024

Útmutatók távirányító

Legújabb útmutatók távirányító

Magnum

Magnum RC-328 Útmutató

9 Április 2025
Conrad

Conrad src 9200 Útmutató

3 Április 2025
Hama

Hama 40095 - 5in1 Útmutató

2 Április 2025
Hama

Hama 20312 - Easytip S9 Útmutató

1 Április 2025
Hama

Hama 20320 - Zapman 4in1 Útmutató

31 Március 2025
Sonos

Sonos Controller for iPhone Útmutató

29 Március 2025
Universal Remote Control

Universal Remote Control UR4U Útmutató

29 Március 2025
ELV

ELV SRC-7000 Útmutató

27 Március 2025
Metronic

Metronic ZAP 2 - 495383 Útmutató

27 Március 2025
Metronic

Metronic 495405z Útmutató

27 Március 2025