Használati útmutató Garmin GC 200
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Garmin GC 200 (18 oldal) a Tengeri kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/18
GC™ 200 IP MARINE CAMERA
Installation Instructions 2
Instructions d'installation 4
Istruzioni di installazione 6
Installationsanweisungen 8
Instrucciones de instalación 10
Installationsvejledning 12
Installeringsinstruksjoner 14
Installationsinstruktioner 16
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GC™ is a trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be
used without the express permission of Garmin.
Pozidriv® is a trademark of the American Screw Company.
June 2019
190-02485-90_0B
GC™ 200 IP Marine Camera
Installation Instructions
Mounting Considerations
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
You can mount the camera upside-down or sideways. You can
reverse the camera image to use in rearview mode. See your
chartplotter owner's manual for instructions.
NOTE: You must update your chartplotter software to setup and
view the camera feed on your chartplotter.
• You must mount the camera in a location where it is not
submerged, does not present a hazard in doorways or
walkways, and cannot be damaged by docks, pilings, or other
pieces of equipment.
• You should mount the camera in a location strong enough to
support the weight of the device and where you can remove
the camera.
• You should mount the camera so the LED is visible and the
cables can be connected easily.
• To avoid interference with a magnetic compass, do not
mount the camera closer to a compass than the compass-
safe distance value listed in the product specifications.
• You should test the camera in the selected location before
you permanently mount the camera.
• You can use the Garmin® Power Module to help make the
installation easier. The Power Module uses a single camera
cable instead of separate power and ethernet cables. This is
especially beneficial when the camera is located far away
from other electronics, such as near the bow or on a mast.
Tools Needed
• Drill and 2 mm (1/16 in.) drill bit
• Pozidriv® screwdriver
Mounting the Camera
1Secure the template to the mounting location.
2Using a 2 mm (1/16 in.) drill bit, drill the pilot holes.
3Using the included hex wrench, loosen the screw in the side
of the camera base.
4Remove the base from the camera body.
5Feed the camera cables through the camera base, or through
one of the cable channels.
6Align the camera base with the pilot holes, and secure the
camera base with the washers and screws .
7Attach the camera to the base, and tighten the screw in
the camera base.
8Connect the camera cables.
9Align the slots on the camera base with the collar lugs ,
and turn the collar until it locks.
Connection Considerations
Connection Diagram with Direct Power
GC™ 200 marine IP camera
Garmin Marine Network cable small connector (included)
Garmin Marine Network Adapter Cable small to large (included)
9 to 18 Vdc power source (not included)
NOTICE
To avoid permanently damaging the camera, do not connect the
camera directly to a 24 Vdc system. You must use a Garmin Power
Module when connecting to a 24 Vdc system.
1 A fast-acting fuse (required, not included)
NOTICE
You must connect the power wire through a 1 A fast-acting fuse
(not included). Without a fuse, the device can malfunction.
Garmin chartplotter (not included)
Connection Diagram with a Garmin Power Module
GC 200 marine IP camera
Garmin Marine Network cable small connector
Power module (010-12527-00, not included)
In-line switch (not included)
9 to 32 Vdc power source (not included)
Chartplotter (not included)
2 Installation Instructions
Camera Status LED
LED Activity Status
Solid red The camera is on.
Solid green The camera is connected to the network and
transmitting data.
Flashing green The camera detects motion.
Specifications
Dimensions (Base W x H) 87 x 79 mm (3.4 x 3.1 in.)
Weight 520 g (1.2 lbs.)
Water rating IEC 60529 IPX71
Operating temperature range From -20 to 60°C (from 14 to 140°F)
Storage temperature range From -30 to 60°C (from -4 to 140°F)
Input voltage From 9 to 18 Vdc
Power module input voltage
(not included)
From 9 to 32 Vdc
Operating current with infrared
on
370 mA
Operating current with infrared
off
210 mA
Power consumption Max 5 W with infrared on
Fuse 1 A fast-acting (required for direct
power connection, not included)
Horizontal viewing angle 99.2 +/- 3 degrees
Vertical viewing angle 74 +/- 3 degrees
Infrared distance 30 m (98.4 ft.)
Compass-safe distance 10 cm (4 in.)
1The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to
www.garmin.com/waterrating.
Installation Instructions 3
Termékspecifikációk
| Márka: | Garmin |
| Kategória: | Tengeri |
| Modell: | GC 200 |
Szüksége van segítségre?
Ha segítségre van szüksége Garmin GC 200, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Tengeri Garmin
15 Január 2025
2 Augusztus 2024
15 Július 2024
14 Július 2024
14 Július 2024
11 Július 2024
4 Július 2024
4 Július 2024
4 Július 2024
3 Július 2024
Útmutatók Tengeri
- Tengeri Raymarine
- Tengeri Lowrance
- Tengeri Humminbird
- Tengeri Rockford Fosgate
- Tengeri ICOM
- Tengeri President
- Tengeri IVT
- Tengeri AdvanSea
- Tengeri Alphatron
- Tengeri Silva
- Tengeri Polmar
- Tengeri Eagle
- Tengeri Navman
- Tengeri Simrad
- Tengeri Furuno
- Tengeri Fusion
- Tengeri Klarfit
- Tengeri BandG
- Tengeri Dickinson Marine
- Tengeri Efoy
- Tengeri Navionics
- Tengeri Echotec
- Tengeri Interphase
- Tengeri Easy
- Tengeri Lofrans
- Tengeri Fastnet
- Tengeri KVH
- Tengeri Standard Horizon
- Tengeri SEAFARER
- Tengeri Nasa
- Tengeri WEST SYSTEM
- Tengeri Katadyn
- Tengeri Sailtron
- Tengeri Lorenz
- Tengeri Raytheon
- Tengeri Geonav
- Tengeri Digital Yacht
- Tengeri Plastimo
Legújabb útmutatók Tengeri
15 Január 2025
5 Október 2024
23 Szeptember 2024
21 Szeptember 2024
21 Szeptember 2024
18 Szeptember 2024
24 Augusztus 2024
24 Augusztus 2024
24 Augusztus 2024
24 Augusztus 2024