Használati útmutató Frigidaire RNAB081J1JBRG

Frigidaire Jéggép RNAB081J1JBRG

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Frigidaire RNAB081J1JBRG (24 oldal) a Jéggép kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/24
AUTOMATIC ICE MAKER
INSTALLATION INSTRUCTIONS
P/N: 240394908
The following items will be required to install the ice maker kit:
• ¼ inch copper supply line with shut off valve
• ¼ inch brass compression nut and ferrule
• Freezer shelf (Some models not equipped with shelf). If your model does not have one, contact your dealer to order
one.
The copper tubing and shut off valve are available in a kit from your local hardware or plumbing supply store. Coil enough
tubing at the back of the unit to allow movement for cleaning.
WARNING
• To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical
power before connecting a water supply line to the refrigerator.
• Connect the ice maker to a potable water supply only.
CAUTION
To Avoid Property Damage:
• Copper tubing is recommended for the water supply line. Water supply tubing made of ¼ inch plastic should not be
used since it greatly increases the potential for water leaks. The manufacturer will not be responsible for any damage
if plastic tubing is used for the supply line.
• DO NOT install water supply tubing in areas where temperatures fall below freezing.
• Chemicals from a malfunctioning water softener can damage the ice maker. If the ice maker is connected to softened
water, ensure that the softener is maintained and working properly.
WARNING
Ice maker kit should be installed only by an authorized service technician.
2
Tools Required:
• Plastic Putty Knife • PhillipsTM Screwdriver
• ¼ inch Socket Wrench or Nut Driver • Needle Nose Pliers
• Adjustable Wrench • Power Drill with PhillipsTM bit
• Small Kitchen Knife
Use This Page to Identify Parts
1. Ice Maker 2. Ice Container 3. Plastic Water Supply Tubing
OR
4. Screws - Qty 2 5. Screws - Qty 2 7. Leveling Bracket - Qty 16. Leveling Bracket Screw -
Qty 1
8. Steel Clamp - Qty 1 10. Water Valves - Qty 19. Plastic Clamp - Qty 2
OR
12. Tube Seal - Qty 111. Water Inlet Tube - Qty 1
3
6. Remove screws securing Access Cover to cabinet
(interior condensers only - see gure 2C).
7. Use small kitchen knife to cut Ice Maker Installation
label on dashed lines located on outside rear panel of
refrigerator in top, right corner. See Figure 3. Push aps
inward until they stick to unit.
NOTE
On some models, there are two plugs on the left freezer
wall that must be removed. These holes will be used to
mount the Ice Maker (1). (There is also a plug on the back
wall where the water inlet tube (11) will be inserted.)
NOTE
Your refrigerator may have an exterior condenser, as
shown in Figure 2A, or an interior condenser, shown in
gure 2B. If your refrigerator has an exterior condenser,
it may be necessary to loosen the two brackets on the
right side of the condenser. Then the condenser can be
pulled away from the back of the refrigerator far enough
to gain easy entry during the installation process.
Figure 2C shows the location of the screws and the
cutout on the access cover.
1. Unplug refrigerator from electrical outlet.
2. Remove ice tray rack from freezer (some models).
3. Remove spacer. Remove freezer shelf (some models) by
pushing shelf to left until right side of shelf comes free
from holes. Then slowly lift up and pull shelf free from
holes on right side.
4. Use a plastic putty knife to remove plugs from inside
freezer compartment. (See Figure 1.)
5. Remove the harness connector cover, where the ice
maker will plug into, by removing the ¼ inch hex head
screw. (See Figure 1.)
ICE MAKER INSTALLATION INSTRUCTIONS
Harness Connector
Cover
Plastic Plugs
¼" Screw
Figure 1
A B
C
Exterior
Condenser
Interior
Condenser
Figure 2
Cut on dashed lines
and push in on aps Figure 3
8. If necessary, remove any foam from within access hole
with needle nose pliers.
Remove and Discard Foam
ICE MAKER
INSTALLATION
ICE MAKER
INSTALLATION
Figure 4

Termékspecifikációk

Márka: Frigidaire
Kategória: Jéggép
Modell: RNAB081J1JBRG

Szüksége van segítségre?

Ha segítségre van szüksége Frigidaire RNAB081J1JBRG, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Jéggép Frigidaire

Frigidaire

Frigidaire RNAB081J1JBRG Útmutató

12 Augusztus 2024

Útmutatók Jéggép

Legújabb útmutatók Jéggép

Spaceman

Spaceman 6250 Útmutató

12 Január 2025
Beper

Beper 70257 Útmutató

12 Január 2025
U-Line

U-Line U-3018CLRINT-00B Útmutató

11 Január 2025
Koenic

Koenic KIM 91221 B Útmutató

11 Január 2025
Eldom

Eldom Cube KS200 Útmutató

11 Január 2025
Eldom

Eldom Cristall KS210 Útmutató

11 Január 2025
Edgestar

Edgestar IB250SSOD Útmutató

11 Január 2025
Edgestar

Edgestar IB121SS Útmutató

11 Január 2025
Edgestar

Edgestar IB250BL Útmutató

11 Január 2025
Summit

Summit BIM182 Útmutató

10 Január 2025