Használati útmutató Fellowes Powershred HS-1010

Fellowes Papír aprító Powershred HS-1010

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Fellowes Powershred HS-1010 (8 oldal) a Papír aprító kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/8
Quality Office oducts Since 1917Pr
POWERSHRED
®
HS-1010
Please read these instructions before use.
Do not discard: keep for future reference.
Veuillez lire ces instructions avant d’utiliser l’appareil.
Ne pas jeter : conserver afin de consulter les directives
ultérieurement, en cas de besoin.
Lea estas instrucciones antes del uso.
No las deseche: consérvelas como referencia futura.
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
• Keepawayfromchildrenandpets.Keephandsawayfrom
paper entry. Always set to off or unplug when not in use.
• Keepforeignobjects–gloves,jewelry,clothing,hair,
etc.–awayfromshredderopenings.Ifobjectenterstop
opening, switch to Reverse ( ) to back out object.R
• Neveruseaerosolproducts,petroleumbasedlubricantsor
other flammable products on or near shredder. Do not use
canned air on shredder.
• Donotuseifdamagedordefective.Donotdisassemble
shredder. Do not place near or over heat source or water.
• ThisshredderhasaDisconnectPowerSwitch(C)inthedoor.Thedoor
must be closed to operate shredder. In case of emergency, open door.
This action will stop shredder immediately.
• Avoidtouchingexposedcuttingbladesundershredderhead.
• Shreddermustbepluggedintoaproperlygroundedwalloutletor
socket of the voltage and amperage designated on the label. The
grounded outlet or socket must be installed near the equipment and
easily accessible. Energy converters, transformers, or extension cords
should not be used with this product.
• Donotoperatethemachinewithoutthesafetyflapclosed(A).
Will shred: Paper only
Will not shred: Adhesive labels, continuous form paper, transparencies,
newspaper, junk mail, credit cards, CD/DVDs, staples, paper clips,
cardboard, laminates, file folders, X-rays or plastic other than noted above
Paper shred size:
High Security Micro-Cut (Din 6) 1/32 in. x 3/16 in. (0.8mm x 5.0mm)....
Maximum:
Sheets per pass .................................................................................10*
Paper entry width 12 in. (305mm) ...........................................................
* 8.5 in. x 11 in., 20lb., (75g) paper at 120V, 60 Hz, 15Amps; heavier
paper, humidity or other than rated voltage may reduce capacity.
Recommended maximum daily usage rates: 5,000 sheets per day. 10
sheets per pass.
* In order to perform at capacity, shredder must be plugged into
a dedicated 20Amp, 120V outlet and auto oil system must
be engaged.
H. Control Panel and LEDs
1. ON/OFF
R
2. Reverse
3. Bin full
4. Door open
5. Safety Flap Open
6. Low oil
7. Auto oil complete
A. Safety Flap
B. Paper entry
C. Disconnect switch (open door)
D. Door
E. Basket - paper (inside)
F. Casters
G. See safety instructions
2
ENGLISH
Model HS-1010
KEY
INDICATOR LIGHTS
CAPABILITIES
ADVANCED PRODUCT FEATURES
Stops automatically
when door is
opened. Symbols
flash alternately
Stops automatically
when bin is full.
Empty bag when
bag full indicator
lights up
Stops automatically
if too much
paper is inserted.
Automatic reverse
if paper jams
Stops automatically
if safety flap is
opened. Symbols
flash alternately
Overload protection.
Machine stops to cool
down- approx. 10-15
minutes. Symbols
flash alternately
Cutting shafts are
automatically oiled Oil bottle is empty
Sleep Mode
Energy saving feature shuts down
the shredder after 1 hour of inactivity
Auto Oil™
Lubricates the cutters automatically to enhance
performance and extend shredder life
A.
B.
G.
H.
F.
E.
D.
C.
R
SHREDDER SET-UP
OILING SET-UP
PAPER
Ensure access
to a dedicated
20Amp, 120V
outlet
3
BASIC SET-UP BASIC SHREDDING OPERATION
Plug in and make
sure door is closed Press ( ) ON to
activate When finished
shredding set to
( ) OFF
Feed paper
straight into paper
entry and release
Do nothing and
shredder will go
automatically to
sleep mode after
1 hour
Make sure safety
flap is securely
in place
•Emptywastebasketwhenbinfullindicatorlightsup.
•Shredderwon’trunifthedoorisopen,orbinneedstobeemptied.
•Maintenanceisanimportantpartofprotectingyourinvestment.Don’tforgettopurchaseouroil(3505801 3604101) and shredder bags ( ).
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
Eliminates frustrating jams by preventing overloads.
Remove lid
from oil bottle Put oil tube into oil
bottle and screw
stopper on
Place oil bottle
into oil holder on
side if cabinet
Close door. Plug
into socket-outlet Oil pump starts
automatically on
first use. To stop Oil
Indicator ( ) from
blinking red, press
ON ( ) after 15
seconds
After changing oil
bottle, press Reverse
(R) until Oil Indicator
( ) no longer
blinks red
R
R
5 6 7 84321
Hook oil
bottle holder
into side of
cabinet
Remove oil bottle
holder from
cabinet
SHEET CAPACITY GAUGE
PAPER JAM
TROUBLESHOOTING AND PREVENTIVE MAINTENANCE
SLEEP MODE
CLEANING AUTO-START INFARED SENSORS
Electronically measures paper thickness to prevent
paper jams:
R
Up to RED: Too many sheets have been
inserted. Automatic reverse of paper.
Up to YELLOW: Maximum sheet capacity.
Up to GREEN: Normal sheet capacity
during shredding process.
In sleep mode To get out of sleep
press ON ( ) insert paper
or
WHEN IN SLEEP MODE
Set to Off ( ) and empty bin. Replace bin and follow the below
procedures.
Stops automatically
if too much paper
is inserted.
Automatic reverse
if paper jams
Gently pull uncut
paper from
paper entry.
Machine runs for
a short time in
reverse. Repeat if
necessary
Shred One Sheet
Paper detection sensors are designed for maintenance free operation. However, on
rare occasions the sensors may become blocked by paper dust causing the motor to
run even if there is no paper present (Note: two paper detection sensors are located in the center
of the paper entry).
Turn off and
unplug shredder Locate Auto-start
infared sensor Clean any
contamination from
the paper sensors
Use thin, long-handled
brush to clean sensors.
Make sure brush is
clean and dry
TO CLEAN THE SENSORS
3
R
2
1
2
1 3
12 3
R
4
R
or
4 51 3
R
2
12

Termékspecifikációk

Márka: Fellowes
Kategória: Papír aprító
Modell: Powershred HS-1010

Szüksége van segítségre?

Ha segítségre van szüksége Fellowes Powershred HS-1010, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Papír aprító Fellowes

Fellowes

Fellowes Powershred 325Ci Útmutató

12 Január 2025
Fellowes

Fellowes Powershred LX25M Útmutató

12 Január 2025
Fellowes

Fellowes Powershred 79Ci Útmutató

15 Október 2024
Fellowes

Fellowes Powershred C-525 Útmutató

8 Október 2024
Fellowes

Fellowes Powershred 225i Útmutató

5 Október 2024
Fellowes

Fellowes MicroShred MS-450Cs Útmutató

29 Szeptember 2024
Fellowes

Fellowes P-35C Powershred Útmutató

24 Szeptember 2024
Fellowes

Fellowes Powershred 1200C Útmutató

22 Szeptember 2024
Fellowes

Fellowes DS-12CS Útmutató

17 Szeptember 2024
Fellowes

Fellowes Intellishred PS-79Ci Útmutató

15 Szeptember 2024

Útmutatók Papír aprító

Legújabb útmutatók Papír aprító

Olympia

Olympia PS 58 CC Útmutató

12 Január 2025
Olympia

Olympia PS 53 CC Útmutató

12 Január 2025
Bonsaii

Bonsaii S123-B Útmutató

11 Január 2025
Bonsaii

Bonsaii C206-G Útmutató

11 Január 2025
GBC

GBC AutoFeed+ 100M Útmutató

5 Január 2025
GBC

GBC ShredMaster SM15-08 Útmutató

5 Január 2025
GBC

GBC ShredMaster PX10-06 Útmutató

5 Január 2025
GBC

GBC Momentum X22-23 Útmutató

5 Január 2025
GBC

GBC ShredMaster PSX12-06 Útmutató

5 Január 2025
GBC

GBC ShredMaster SX15-06 Útmutató

5 Január 2025