Használati útmutató Extron DVI-RGB 200

Extron audio/videó-konverter DVI-RGB 200

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Extron DVI-RGB 200 (2 oldal) a audio/videó-konverter kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
This guide provides instructions for an experienced installer to set up and operate Extron DVI-RGB 200 ®
DVI to Analog RGB Video Interface.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the interface as required.
Step 2 — Connections and Initial Settings
a Connect a single link of direct DVI-D Input connector —
digital video to this DVI-I connector using the included cable.
b Buffered Loop-through connector — If desired, connect a
direct digital local monitor to this DVI-I connector.
NOTE: Use only cables specifically intended for DVI interfaces. Use of non-DVI cables or modified cables can cause
the DVI-RGB 200 to not operate correctly.
c Connect an RGB display to these female BNC connectors. Connect the Output connectors —
BNCs as shown at right for the desired RGB video format.
NOTE: Ensure that the SOG DIP switch (f) is turned off (down) for RGBHV and RGBS
video.
Ensure that the SOG DIP switch is turned on (up) for RGsB video.
d EDID Source switch —
Set this switch to the Monitor (up) position to connect the DDC channel between the direct
digital video source and the local monitor.
Set this switch to the Selector (down) position to connect the DDC channel between the
direct digital video source and the built-in DVI-RGB 200 EDID logic.
e If the EDID Source switch (EDID Select — d) is in the Selector (down) position, set this switch
to the appropriate position to select the desired video resolution. Use the Refresh DIP switch
(f) to select the refresh rate. The table at right identifies the
switch positions and the associated resolutions and vertical
refresh rates.
f DIP switches —
SOG (Sync on Green) On/Off switch — Set this switch to the
On (up) position to enable SOG for RGsB video. Set this switch
to the Off (down) position to disable SOG for RGBS or RGBHV
video.
Refresh switch —
If the EDID Source switch (d) is in the Selector position (down)
and the EDID select switch (e) is in position 1 through F
position, set this switch either up or down to select the refresh
rate of the selected output. See the table at right.
If the EDID Source switch (d) is in the Selector (down) position and the EDID select switch is in position 0, set this switch
up to capture the EDID data from the connected Buffered Loop-through monitor. See Capturing a User-recorder EDID.
g AC power connector — Plug a standard IEC power cord into this connector to connect the interface to a
100 to 240 VAC, 50 Hz or 60 Hz power source.
100-240V 0.4A
OUTPUT
DVI-D INPUT BUFFERED
LOOP-THROUGH
R
H
G
V
B
S
SO G O N/OFF
REFRESH
EDID
SO URCE
MONIT OR
HIG H
LO W
SELECT OR
EDID
SELECT
DVI-RGB 200
50/60 Hz
21 57 364
R
H
G
V
B
S
R
H
G
V
B
S
R
H
G
V
B
S
RGBHV
RGBS
RGsB
Pos. Resolution
EDID Select
Switch
Refresh
DIP Switch
0 User EDID EDID capture
1
2 1024x768
3 1280x720
50 Hz 60
50 Hz 60
50 Hz 60
4
5
1280x768
1280x800
50 Hz 60
50 Hz 60
800x600
< >
Dwn Up
8
9
A
B
1366x768
1400x1050
Pos. Resolution
50 Hz 60
50 Hz 60
C
D
1440x900
1600x1200
50 Hz 50
50 Hz 60
6
7
50 Hz 60
50 Hz 60
E
F
50 Hz 50
50 Hz 60
50 Hz 60
Refresh
DIP Switch
<
>
Dwn Up
EDID Select
Switch
1280x1024
1360x768
1680x1050
1920x1080
1920x1200
N/A
1
DVI-RGB 200 Setup Guide
Operation
Apply power to the devices in the following order: 1) DVI-RGB 200, 2) display device, 3) input device. After all devices are
powered up, the system is fully operational.
If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the
Extron S3 Sales & Technical Support Hotline that is closest to you, at the number shown below.
NOTES: • High-bandwidth Digital Content Protection (HDCP) is an encryption method that protects copyrighted digital
entertainment material that uses DVI video.
• The DVI-RGB 200 cannot respond to the HDCP decryption key. When the DVI input is HDCP encrypted, the
output of the DVI-RGB 200 RGB is blank.
• The computer reads the DDC on power up to determine the direct digital video resolution and refresh rate
to output. Ensure that the local DVI monitor and the RGBHV monitor can both display the selected resolution
and refresh rate, otherwise images may be distorted or missing.
• Ensure that the computer and local monitor are connected to the DVI-RGB 200, and the DVI-RGB 200 and
local monitor have power applied, before applying power to the computer. If the other devices are not
turned on before the computer is powered on, the image will not appear.
Front Panel Controls and Indicator
NOTE: Level Boost and Peaking have no affect on the DVI
output of the Buffered Loop-through connector.
h The two-color Power LED lights amber or Power LED —
green:
Amber when the DVI-RGB 200 is receiving power but no DVI input signal is applied.
Green when the DVI-RGB 200 is receiving power and a DVI input is present.
i Level Boost control — The Level Boost control alters the brightness of the picture on the RGB output. Judge the
adjustment visually by looking at the display.
• At the minimum level setting (the counterclockwise limit of this control), the interface outputs video at 0.7 Vp-p.
• At the maximum level setting (the clockwise limit of this control), the interface outputs video at 1.45 Vp-p.
Select a level setting of 0.7 V and above to compensate for the signal level decrease that occurs with long cables. Set
the level at the maximum setting for cable lengths over 500 feet.
j Peak(ing) control — The Peaking control affects the sharpness of the RGB output. Increased peaking can compensate
for detail (mid- and high-frequency) loss from low bandwidth or long cables. The minimum setting (counterclockwise
limit) provides no peaking. The maximum setting (clockwise limit) provides 100 percent peaking.
Capturing a User-recorded EDID
Record the EDID from a display connected on the Buffered Loop-through connector as follows:
1. Set the rear panel EDID Source switch to the Selector (down) position.
2. Set the Output Resolution switch to the 0 position.
3. Change the Refresh dip switch to on (up).
NOTE: The front panel Power LED lights amber whether the DVI-D Input connector is receiving a signal or not.
4. Connect the display device to Buffered Loop-through connector.unpowered
5. Power on the display device. The DVI-RGB 200 copies the EDID of the display connected in step to its memory.4
After the EDID is successfully copied, the front panel Power LED lights green.
6. Set the Refresh DIP switch to off (down).
68-1791-50
Rev A
10 10
DVI-RGB 200
DVI TO RGB CONVERTER
BOOST
LEVEL
CONT ROL
PEAK
8 9 10
SOG ON/OFF
REFRESH
DDC
SOURCE
MONITOR
HIGH
LOW
SELECTOR
EDID
SELECT
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.833.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2010 . All rights reserved. Extron Electronics www.extron.com
2
DVI-RGB 200 Setup Guide (Continued)

Termékspecifikációk

Márka: Extron
Kategória: audio/videó-konverter
Modell: DVI-RGB 200

Szüksége van segítségre?

Ha segítségre van szüksége Extron DVI-RGB 200, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók audio/videó-konverter Extron

Extron

Extron FOX II AEX 108 MM Útmutató

3 Szeptember 2024
Extron

Extron HDP 101 4K Útmutató

3 Szeptember 2024
Extron

Extron RGB 192V Útmutató

3 Szeptember 2024
Extron

Extron DVI-RGB 200 Útmutató

3 Szeptember 2024
Extron

Extron BUC 202 Útmutató

23 Augusztus 2024

Útmutatók audio/videó-konverter

Legújabb útmutatók audio/videó-konverter

TV One

TV One 1T-EDID-11 Útmutató

8 Április 2025
BZBGear

BZBGear BG-UHD-18GFE Útmutató

3 Április 2025
PureTools

PureTools PT-C-HDEARC-4K Útmutató

2 Április 2025
ATen

ATen VE170Q Útmutató

2 Április 2025
ATen

ATen VS1808T Útmutató

2 Április 2025
INOGENI

INOGENI U-BRIDGE 3 Útmutató

2 Április 2025
Sescom

Sescom SES-X-FA2LXBT01 Útmutató

2 Április 2025
Teradek

Teradek COLR Útmutató

29 Március 2025
Pengo

Pengo VideoSync Grabber Box Útmutató

29 Március 2025
Mean Well

Mean Well PSD-45B-24 Útmutató

26 Március 2025