Használati útmutató Extron DTP HD DA 4K 230

Extron nincs kategorizálva DTP HD DA 4K 230

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Extron DTP HD DA 4K 230 (3 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/3
1
DTP HD DA4/DA8 4K 230/330 • Setup Guide
Overview
These Extron distribution ampliers distribute one HDMIinput signal to four (DTP HD DA4 4K models) or eight (DTP HD DA8 4K
models) simultaneous outputs via shielded twisted pair (STP) cables. The ampliers distribute the signal over a distance of up
to 230 feet (70 meters) or 330 feet (100meters) for resolutions up to 1080p @ 60 Hz, and 130 feet (40 meters) or 330 feet (100
meters) for resolutions up to 4K @ 30 Hz, depending on the model. This setup guide provides basic instructions for installation by
an experienced installer. For complete instructions, see the user guide on the Extron web site DTP HD DA4/DA8 4K 230/330
(www.extron.com).
Typical DTP HD DA4/DA8 4K Application Examples
100-240 V ~ 1.0A MAX
50/60 Hz
DT P HD DA4 330
LAN
3 41 2
OU TPUTSNPU T
HD MI LO OP TH RU
REMOTE
Tx Rx
RS -2 32
G
RE SE T
DTP
HDBT
Tx Rx Tx RxG
RS -232 IR
Tx Rx Tx RxG
RS -232 IR
OVER TP
DTP
HDBT
Tx Rx Tx RxG
RS -232 IR
Tx Rx Tx RxG
RS -232 IR
OVER TP
DTP
HDBT
DTP
HDBT
AUD IO
S IG
O T
LINK S IG
OUT
LINK S IG
O T
LINK S IG
OUT
LINK
HD MI HD MI3
HD MI4
21 C O N FI G U R AB LE
100- 240V ~ - -A MAX
50-6 0 Hz AUD I O O U P U T
T ALLY OUT
CO NT AC T IN
L
1 2 R
L R
TxRx G
321 4 +V
1 2 3 4 G
RS-232
O U T
IN
HD MI
INP UT RE MO T E
POWER
12V
0.3A MAX
IPL RO S3
Tx Rx RTS CTS GTx Rx RTS CTS GTx Rx RTS CTS
COM COM COM 1 2 3
LAN / PoE
MODEL 8 0
FLAT PANEL
MODEL 8 0
FLAT LPANE
MODEL 8 0
FL NEAT PA L
MODEL 8 0
FL NEAT PA L
iPad
RS-232
Displays with Speakers
HDMI
CATx e Cabl
up to 330' (100 m) CATx e Cabl
up to 330' (100 m)
RS-232HDMI RS-232HDMI RS-2
32
HDMI
Extron
DTP HDMI
33 Rx0 D
Receiver
Extron
DTP HDMI
33 Rx0 D
Receiver
VGA
La La Laptop ptop ptop Tablet
Audio HDMI HDMI HDMI
HDMI RS-232
Eth Ethernet ernet
Ethernet
TCP/IP
Net wor k
Extron
TL PrP o 320C
3.5" e y Cabl Cubb
TouchLink o Pr
Touchpanel
Extron
IN1604 HD
Four t Inpu
Scaler
Extron
IPL o Pr S3
IP o Link Pr
Control
Processor
Extron
DTP HD DA4 04K 33
DTP rDistribution Amplie
100-240V ~ 1.0A MAX D P HD DA8 230
LAN
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OV ER TP
3 4 5 6 7 81 2
DTP
HDBT
OU T P U T SNP UT
HDMI LOOP THR U
REM O T E
Tx Rx
RS -232
G
RES ET
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OV ER TP
DTP
HDBT
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OV ER TP
DTP
HDBT
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OV ER TP
DTP
HDBT
DTP
HDBT
AUDIO
SIG
O T
LINK SIG
OU T
LINK SIG
O UT
LINK SIG
O T
LINK SIG
O T
LINK SIG
O T
LINK SIG
O UT
LINK SIG
O T
LINK
OUTPUTS
UDIO
Tx T x Rx
RS-232 I R
OVER DTP
OUTPUTS
DIO
TxR T x Rx
RS-232 IR
OVER DTP
OUTPUTS
UDIO
Tx T x Rx
RS-232 I R
OVER DTP
HDM I HDM I3
HDM I4
21 CO NFIG URAB LE
100-240V ~ --A MA X
50-60 Hz AUDIO OUT PUT
T ALLY OU T
CON TACT IN
L
1 2
R
L R
Tx Rx G
321 4 +V
1 2 3 4 G
RS -232
OUT
IN
HDM I
INP UT REM O T E
POWER
12V
0.3A MAX
IP L PRO S3
Tx Rx RTS CTS GTx Rx RTS C TS GTx Rx RTS CTS
COM 1 COM 2 COM 3
LAN / PoE
50/60 Hz
M O D EL 80
FLAT NELPA
M O D EL 80
FLAT NELPA
M O D EL 80
FLAT NELPA
M O D EL 80
FLAT NELPA
M O D EL 80
FLAT NELPA
M O D EL 80
FLAT NELPA
M O D EL 80
FLAT NELPA
M O D EL 80
FL N ELATPA
iPad
LAPTOP
PC
DVD
DOC CAM
AUXILIARY
DISPLAY ON
DISPLAY OFF
MU TE
VO LUM E
VO LUM E
RS-232
Displays with
Speakers
HDMI
CATx Cable
up to 330' (100 m)
CATx Cable
up to 330' (100 m)
Ext
ron
DT
P HDMI
33
0 D Rx
Re
ceiver
RS-232HDMI
Extron
DTP HDMI
33 Rx0 D
Receiver
VGA
La La Laptop ptop ptop Tablet
Audio HDMI HDMI HDMI
HDMI RS-232
Ethernet Ethernet
Ethernet
TCP/IP
Net work
Extron
TLP Pro 320C
3.5" Cable Cubby
TouchLink Pro
Touchpanel
Extron
IN1604 HD
Four Input
Scaler
Extron
IPL Pro S3
IP Link Pro Control
Processor
Extron
DTP HD DA8 04K 33
DTP Distribution
Amplier
Front Panel
CONFIG
DTP HD 4DA
INPUT OUTPUTS
SIGNAL
HDCP
DTP DISTRIBUTION AMPLIFIER
LOOP
THRU
3 41 2
CONFIG
DTP HD 8DA
INPUT OUTPUTS
SIGNAL
HDCP
DTP DISTRIBUTION AMPLIFIER
LOOP
THRU
3 4 56 7 8
12
A B F
E
D
C
A B F
E
D
C
A Power status LED — Lights green when power is
applied to the unit.
B USB Config port — Used for rmware updates,
SIS conguration, and software control.
C Input Signal LED Lights green indicating a
signal is detected on the HDMI input.
D Input HDCP LED Lights green indicating
HDCP presence is detected on the HDMI input.
E Output Signal LEDs — Light green indicating a
signal is detected on the HDMI outputs.
F Output HDCP LEDs — Light green indicating
HDCP presence is detected on the HDMI outputs.
2
DTP HD DA4/8 4K 230/330 • Setup Guide (Continued)
Rear Panel
50/60Hz
100-240V 1.0A
DTP HD DA4 330
LAN
3 41 2
DTP
HDBT
OUTPUTSINPUT
HDMI LOOP THRU
REMOT E
Tx Rx
RS-232
G
RESET
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
DTP
HDBT
AUDIO
50/60Hz
100-240V 1.0A
DTP HD DA8 330
LANDTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
3 4 5 6 7 81 2
DTP
HDBT
OUT
SIG LINK
DTP
HDBT
OUTPUTS
INPUT
HDMI LOOP THRU
REMOT E
Tx Rx
RS-232
G
RESET
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
OUT
SIG LINK
Tx Rx Tx RxG
RS-232 IR
Tx Rx Tx RxG
RS-232 IR
OVER TP
OUT
SIG LINK
DTP
HDBT
DTP
HDBT
AUDIO
A C I
B D E F G H J K
A C I
B D E F G H J K
A Power input — Connect the provided IEC connector to a 100-240 VAC (50 or 60 Hz) power source.
B Analog audio input — Connect an unbalanced stereo audio source to these 3.5 mm mini stereo jacks.
NOTE: The units do NOT embed analog audio onto the HDMI signal. This analog audio signal is transmitted
simultaneously with audio embedded within the HDMI signal.
C Analog audio Loop Thru Connect an audio system to this 3.5 mm mini stereo jack for local loop-through monitoring
of the source audio.
D HDMI input — Connect a source device to this female HDMI type A connector.
E HDMI Loop Thru — Connect a display to this female HDMI type A connector for local loop-through monitoring of the
source signal.
F DTP/HDBaseT configuration switch Set this 2-position, recessed switch to congure the output between HDBaseT
and DTP modes. When congured for HDBaseT, use an HDBaseT-compatible receiver. When congured for DTP, use a
DTP-compatible receiver.
G DTP/HDBaseT outputs Use shielded twisted pair (STP) cables to connect these 4 (DA4 models) or 8 (DA8 models)
outputs to the inputs of a compatible receiver.
ATTENTION:
Do not connect these outputs to a telecommunications or computer data network.
Ne connectez pas ces appareils à des données informatiques ou à un réseau de télécommunications.
H Over TP RS-232/IR connectors — Use these 4 (DA4 series) or 8 (DA8 series) 3.5 mm, 5-pole captive screw connectors
to pass bidirectional RS-232 and IR control between compatible devices.
I Reset button and LED — Press and hold the reset button for approximately 6 seconds to restore the unit to factory
default settings. The reset LED will ash green, indicating that the default settings have been restored.
J LAN connector — Use an RJ-45 cable to connect this jack to a LAN for Ethernet control of the device.
K Remote RS-232 connector — Connect an RS-232 device to this 3-pole, 3.5 mm captive screw connector to control the
DTP HD unit. Congure it as follows: 9600 baud rate, 8 data bits, 1 stop bit, no parity. See on the next page Installation
for wiring instructions.
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2015 Extron Electronics All rights reserved. www.extron.com
3
68-2545-50 Rev. A
01 15
DTP HD DA4/DA8 4K 230/330 • Setup Guide (Continued)
Installation
1. Mount the HDMI DA unit in a suitable location (see the section of the user guide for Mounting DTP HD DA4/DA8 4K 230/330
mounting options). Follow the instructions provided with the mounting kit.
2. Connect the USB or RS-232 connector (see the gure below) to a PC for conguration and maintenance. Use SIS commands
or the Extron PCS program to congure EDID Minder, mute the video signal, mute the audio signal, adjust the video color
bit depth, or monitor the signal and HDCP status, as required (see the user guide for more DTP HD DA4/DA8 4K 230/330
information).
RS-232
Tx Rx G
REMOTE
TransmitReceive
ReceiveTransmit
GroundGround
DB9 Pin Locations
Female
5 1
9 6
Pin 2 = Rx
Pin 3 = Tx
Pin 5 = G
Computer DTP HD DA4/DA8
3. Connect the rear panel transmitter outputs (
G) to the rear panel receiver inputs using shielded twisted pair (STP) cable.
NOTE: The DTP HD DA4/DA8 4K 230 and 330 products can transmit video, control, and audio (if applicable) signals up
to 230 feet (70 meters) and 330 feet (100 meters), respectively.
For optimal performance, Extron highly recommends the following:
zRJ-45 termination with STP cable must comply with TIA/EIA-T568B wiring standard for all connections. For more
information on cable wiring and termination, see the full product user guide at www.extron.com.
zUse shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable bandwidth of 400 MHz.
ATTENTION:
Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable.
N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou le câble STP201.
zUse shielded RJ-45 plugs to terminate the cable.
zLimit the use of RJ-45 patches. Overall transmission distance capabilities vary depending on the number of patches
used. If possible, limit the number of patches to only 1 or 2 total.
zIf RJ-45 patches must be used in the system, Extron recommends shielded CAT 6 (or better) patches.
4. Connect display devices to the transmitter and receivers.
NOTE: Use the LockIt HDMI cable lacing brackets provided to secure the HDMI connectors (see the LockItHDMICable
Lacing Bracket installation guide).
a. Connect and power on the display devices to the outputs on the compatible receivers.
b. (Optional) Connect and power on a local display device to the Loop-Thru connector (E).
5. Connect to a 110-240 VAC (50 or 60 Hz) power supply using the provided IEC power cord.
6. Connect and power on the source device.

Termékspecifikációk

Márka: Extron
Kategória: nincs kategorizálva
Modell: DTP HD DA 4K 230

Szüksége van segítségre?

Ha segítségre van szüksége Extron DTP HD DA 4K 230, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Extron

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva