Használati útmutató ETC Irideon FPZ (22 oldal)

Part Number: 7191M1200-1.0.1 Rev: D

Released: 2019-06

Irideon FPZ

User Manual

V

VVersion 1.0

ersion 1.0

ersion 1.0ersion 1.0

To view a list of ETC trademarks and patents, go to

etcconnect.com/ip

etcconnect.com/ipetcconnect.com/ip

.

All other trademarks, both marked and not marked, are the property of

their respective owners.

ETC intends this document, whether printed or electronic, to be

provided in its entirety.

Table of Contents

Table of Contents i

Introduction . . . . . . . . . . . . . . . . . . . . . . . 1

Specifications. . . . . . . . . . . . . . . . . . . . . . . 3

Basic Assembly. . . . . . . . . . . . . . . . . . . . . . 4

Installation. . . . . . . . . . . . . . . . . . . . . . . . . 4

Install Track-Mounted Fixture. . . . . . . . . . . . . 4

Install Canopy Fixture (DMX variant) . . . . . . . 5

Install the Voltage Barrier

(DMX variant) . . . . . . . . . . . . . . . . . . . . . . . 5

Connect Canopy Wiring (DMX variant) . . . 6

Install the Mounting Plate and

Complete the Wiring (DMX variant) . . . . . 8

Install Canopy Fixture (0–10 V and DALI

variants) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Install Portable Fixture with C-clamp . . . . . . 13

Install Portable Fixture on Unistrut Track . . 14

Connect Cables to Portable Fixture . . . . . . . 14

Portable Fixture DMX Pinout . . . . . . . . . . 15

Set the DMX Address on the Fixture . . . . . . 15

Alternative DMX Addressing Functions . . 17

Adjust the Local Intensity . . . . . . . . . . . . . 17

Initial Power Up . . . . . . . . . . . . . . . . . . . . . . . 18

Status LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

User Manual 1

Introduction

IntroductionIntroduction

The Irideon FPZ takes the beauty and punch of the Source Four Mini beam and

puts it into a fixture designed to work in any architectural environment.

The Irideon FPZ has three available mounting options:

• Track-mount—For use with the DataTrack track system.

• Portable—Includes a miniature C-clamp and yoke-mounted driver, and

has a permanently installed power cord with 3-prong Edison connector.

Region-specific connectors are available. Contact ETC for available

options. Use L5-15 plugs on branch circuits with L5-15 receptacles only.

• Canopy—Available in three different control variants:

- 0–10 V

- DALI

- DMX

Note:

Note:Note:

The miniature C-clamp for the portable fixture is

available only in non-EU markets. Within the EU, use an

M12 bolt to secure a C-clamp (provided separately) to the

fixture.

Portable

PortablePortable

Track-mount

Track-mountTrack-mount

Canopy

CanopyCanopy

User Manual 3

Spe

SpeSpecific

cific

cificcification

ation

ationations

s

ss

Physical

PhysicalPhysical

• Steel yoke with 0.406” (10.3 mm) diameter

mounting hole

• Rotating shutter assembly ±175°

• E-size gobo pattern holder (included) 1-1/2”

(37.5 mm) with a 1” (25.4 mm) image area

• IP20 rated

• Zoom range to suit a variety of throw

distances

• Captive accessory slot for pattern holder

(included)

• Locking, stainless steel, full hard shutters in

a tri-plane assembly, 0.40 mm (A301 grade)

• Magnetically held integrated media holder

for 2.6” (66 mm) diameter color media or

diffusion or 1.75 mm-thickness dichroic

glass

• Track-mount fixture:

- Compatible and ETL-listed for DataTrack

(EUTRAC) brand track

- DataTrack color matching track adapter

included

• Portable fixture:

- C-clamp (included in non-EU markets)

- Optional accessory for Unistrut

®

mounting (order separately, part number

7191K1000)

• Canopy fixture:

- Can be installed directly on 4” and

4-11/16” backboxes, or on backboxes

with round cover plates

- Not for installation on 1-gang backboxes

or trim rings

Electrical

ElectricalElectrical

• Power at full intensity: 20 W (typical),

24 W (maximum)

• Input voltage options:

- Track-mount and portable: 100–240 V,

50/60 Hz

- Canopy (0–10 V and DALI): 120–277 V,

50/60 Hz

- Canopy (DMX): 100–277 V, 50/60 Hz

• Portable fixture: 6 ft power cable hard-wired

to fixture with mains connector options of

NEMA 5-15P, Schuko, or UK

• Inrush (first half-cycle) for 0–10 V and DALI

canopy fixtures:

- 120 V: 2 A

- 240 V: 5 A

- 277 V: 6 A

• Inrush (first half-cycle) for all other fixtures:

- 120 V: 11 A

- 240 V: 24 A

- 277 V: 28 A

• All variants require power from a non-

dimmable source

LEDs

LEDsLEDs

• Cree LED source

- Irideon FPZ 2700 K Gallery: 90+ CRI

- Irideon FPZ 3000 K: 80+ CRI

- Irideon FPZ 3000 K Gallery: 90+ CRI

- Irideon FPZ 4000 K: 80+ CRI

- Irideon FPZ 5000 K: 80+ CRI

• Long-life LED: 70,000 hours L70 lumen

maintenance

Optical

OpticalOptical

• Built-in zoom optics

(25–50 degree field-angle)

• Beam edge continually adjustable

hard to soft

• Projector-quality, high-contrast lenses

Thermal

ThermalThermal

• 0°C to 40°C (32°F to 104°F) ambient operating temperature

4 Irideon FPZ

Basic Assembly

Basic Assembly Basic Assembly

Installation

Installation Installation

Install T

Install TInstall Track-

rack-

rack-rack-

Mounted Fixture

Mounted FixtureMounted Fixture

1: Insert the DataTrack

adapter into the track.

The adapter only fits into

the track one way with

the tabs nesting into the

track’s groove.

2: Rotate the locking

mechanisms to lock the

adapter into place.

3: Use the circuit selection

lock to select the circuit.

The desired circuit

number should point toward the center of the adapter.

WARNING:

WARNING:WARNING:

When using the circuit selection lock, ensure that the

When using the circuit selection lock, ensure that the When using the circuit selection lock, ensure that the

selected circuit is a constant

selected circuit is a constant selected circuit is a constant power circuit. Dialing into a

power circuit. Dialing into a

power circuit. Dialing into a power circuit. Dialing into a

dimmable circuit may cause fixture damage that will void

dimmable circuit may cause fixture damage that will void dimmable circuit may cause fixture damage that will void

the ETC warranty.

the ETC warranty.the ETC warranty.

Yoke

YokeYoke

Integrated media

Integrated mediaIntegrated media

holder

holderholder

Shutters x4

Shutters x4Shutters x4

Beam zoom an

Beam zoom anBeam zoom and

d

d d

focus knobs

focus knobsfocus knobs

Pattern holder

Pattern holderPattern holder

slot

slotslot

(Illustration shows fixture body only)

(Illustration shows fixture body only)(Illustration shows fixture body only)

Circuit

Circuit Circuit

selection lock

selection lockselection lock

Locking

Locking Locking

mechanism

mechanismmechanism

User Manual 5

Install Canopy Fixture (DMX variant

Install Canopy Fixture (DMX variantInstall Canopy Fixture (DMX variant)

)

))

Install the V

Install the VInstall the Voltage Barrie

oltage Barrie

oltage Barrieoltage Barrier (DMX va

r (DMX va

r (DMX var (DMX variant)

riant)

riant)riant)

The DMX variant of the canopy fixture includes a voltage barrier to separate

the data network from the line voltage inside the backbox. Voltage barriers are

provided for both 4” and 4-11/16” backboxes.

Install the voltage barrier in the backbox with

the provided screw, separating the power

side from the data side (see image at right).

Note:

Note:Note:

The canopy fixture can be installed directly on 4” and

4-11/16” backboxes, or on backboxes with round cover

plates. The canopy fixture cannot be installed on 1-gang

backboxes or trim rings.

CAUTION:

CAUTION:CAUTION:

• DMX control is a Class 2 circuit. DMX wiring cannot be

run through the same conduit as line voltage power-

supply conductors.

• Separate the line voltage from the data side in the

backbox. Install the voltage barrier provided by ETC.

6 Irideon FPZ

Connect Canopy Wiring (DMX variant)

Connect Canopy Wiring (DMX variant)Connect Canopy Wiring (DMX variant)

Cable preparation instructions for DMX termination are included in the

termination kits, and are also available for free download at etcconnect.com

etcconnect.com

etcconnect.cometcconnect.com.

1: Remove the adhesive tape or fasteners securing the mounting plate to

the fixture to free the mounting plate from the canopy enclosure.

2: Are you flush-mounting the fixture or surface-mounting the fixture?

•Flush-mounting

Flush-mounting

Flush-mountingFlush-mounting:

:

:: Continue to step 3.

•

Surface-mounting:

Surface-mounting:Surface-mounting:

Position the cover

plate on top of the

mounting plate

before wiring the

fixture. The cover

plate is required

when the interior of the canopy enclosure could be exposed after

installation with only the mounting plate (the mounting surface is

smaller than the canopy enclosure).

3: Terminate DMX/RDM input from the

control source to the backbox.

If using Belden 9729:

a: See the

DMX Cable Preparation

for Screw Termination Setup

Guide

for instructions to prepare

and terminate Belden 9729 for

DMX input cable to the screw

terminal connector.

b: Install the screw terminal

connector with wires terminated

to the DMX/RDM Input receptacle

on the termination board.

WARNING:

WARNING:WARNING:

RISK OF ELECTRIC SHOCK! Install the cover plate as

RISK OF ELECTRIC SHOCK! Install the cover plate as RISK OF ELECTRIC SHOCK! Install the cover plate as

directed below for installations where the

directed below for installations where the directed below for installations where the interior of the

interior of the

interior of the interior of the

canopy enclosure could be exposed after install

canopy enclosure could be exposed after installcanopy enclosure could be exposed after installation

ation

ation ation

with only the mounting plate. For example, ins

with only the mounting plate. For example, inswith only the mounting plate. For example, install the

tall the

tall the tall the

cover plate when installing to a surface-mount backbox.

cover plate when installing to a surface-mount backbox. cover plate when installing to a surface-mount backbox.

Mounting plate

Mounting plateMounting plate

Cover plate

Cover plate Cover plate

(if

(if(if needed for

needed for

needed for needed for

surface-mounting)

surface-mounting)surface-mounting)

From a DMX/RDM source

Data – (Black)

Data + (Red)

Belden 9729 (or equivalent) wire

termination to screw connector

4 to 8 = n/c

COM

User Manual 7

If using Category 5:

a: See the

Cat5 Cable Preparation for

IDC Termination Setup Guide

for

instructions to prepare and

terminate Category 5 for DMX/RDM

input cable to the insulation

displacement connector.

b: Install the IDC connector with wires

terminated to the DMX/RDM Input

receptacle on the termination board.

4: Optionally, terminate DMX/RDM thru to

the next device in the DMX data run.

Up to 32 DMX/RDM devices can be

daisy-chained together per data run.

a: See the specific termination setup guide for the type of cable used

(either Belden 9729 or Category 5) in the installation. Termination

kits are ordered separately.

b: Install the connector with wires terminated to the DMX/RDM Thru

receptacle on the termination board.

5: Connect the building ground wire to the power block on the fixture.

6: Following the label on the mounting plate, attach the power wires to

the power block.

Data – (ORG)

Data + (W/ORG)

Cat5 (or equivalent) wire

termination to IDC connector

COM

BRN

GRN

W/GRN

BLU

W/BLU

DMX

DMX DMX

termination

terminationtermination

board

boardboard

Power block

Power blockPower block

8 Irideon FPZ

Install the Mounting Plate and Complete the

Install the Mounting Plate and Complete the Install the Mounting Plate and Complete the

Wiring (DM

Wiring (DMWiring (DMX variant)

X variant)

X variant)X variant)

1: Secure the mounting plate (or the

combination of mounting plate and

cover plate for surface-mounting) to

the installed backbox, positioning

the plate so that the power side and

data side are separated by the

voltage barrier in the backbox. See

Install the Voltage Barrier (DMX

Install the Voltage Barrier (DMX Install the Voltage Barrier (DMX

variant)

variant)variant)

on

page 5

page 5page 5

.

For this structure...

For this structure...For this structure... ...secure mounting plate using:

...secure mounting plate using:

...secure mounting plate using:...secure mounting plate using:

4-11/16” backbox Large oval slots (see 1 above)

4” backbox Small oval slots (see 2 above)

Mounting

Mounting Mounting

plate

plateplate

Canopy

Canopy Canopy

screws

screwsscrews

Mounting

Mounting Mounting

plate screws

plate screwsplate screws

Cover plate

Cover plate Cover plate

(if

(if(if needed

needed

needed needed

for surface-

for surface-for surface-

mounting)

mounting)mounting)

(DMX variant

(DMX variant (DMX variant

shown)

shown)shown)

Canopy

Canopy Canopy

screw

screwscrew hole

hole

holehole

Mounting plate

Mounting plate Mounting plate

(DMX variant)

(DMX variant)(DMX variant)

2

22 1

1

11

2

22

1

11

User Manual 9

5: Terminate DMX/RDM data signal for the last DMX/RDM device in the

data run by setting the termination switch to ON (to the right, as shown

below). All other devices in the data run should retain the default

setting for the termination switch (OFF).

6: Following the label on the mounting plate, attach the power wires to

the power block.

7: Use the canopy screws to secure

the fixture to the mounting plate.

CAUTION:

CAUTION:CAUTION:

Make sure that the

wiring is clear of the

mounting plate before

you secure the fixture.

Hook

HookHook

2: Use the hook in the canopy enclosure to hang the

fixture from the mounting plate while you complete

the fixture wiring.

3: If desired, manually set the DMX address on the

fixture using the three addressing dials in the canopy.

See

Set the DMX Address on the Fixture

Set the DMX Address on the FixtureSet the DMX Address on the Fixture

on

page 15

page 15page 15

.

4: Connect the pre-wired DMX connector on the fixture

to the mated connector on the mounting plate

(shown below).

ON

Mounting plate

Mounting plate Mounting plate

DMX

DMXDMX connec

connec

connecconnector

tor

tortor

Termination switch

Termination switchTermination switch

Power block

Power blockPower block

Canopy

Canopy Canopy

screws

screwsscrews

Márka:	ETC
Kategória:	Lampa
Modell:	Irideon FPZ

Használati útmutató ETC Irideon FPZ

Termékspecifikációk

Szüksége van segítségre?

Útmutatók Lampa ETC

Útmutatók Lampa

Legújabb útmutatók Lampa