Használati útmutató Enviroswim ES-3

Enviroswim nincs kategorizálva ES-3

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Enviroswim ES-3 (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

Enviroswim ES- 3 Installation Guide

©Enviroswim 2014 Enviroswim 2014 © V3.0AU

These instructions are repeated in the Operating Manual and should be repeated every time the pool is refilled.

1. Ensure that unwanted compounds are eliminated from the water.

Parameter

Required

Notes and Treatment

Metals

<recommended for

that metal

Test unusual supplies such as bore water for excessive amounts of

metals in particular, manganese, iron and magnesium. There are –

dierent recommended maximums. Remove using appropriate

sequestering agents.

Phosphates

< 100ppb/0.1ppm

Use phosphate remover.

Copper

< 0.1 ppm

Dilute or use a sequestering agent to reduce. Note: To establish the

copper ions and proportionate silver ions with the Enviroswim

process require there is no signicant residual copper in the.

2. Adjust water balance

Parameter

Minimum

Ideal Range

Maximum

Adjust by

6.8

7.1 7.5-

7.6

Use Hydrochloric Acid or Sodium Bisulphate to

reduce. Sodium Bicarbonate to increase.

Calcium

Hardness

160

200-250ppm

400

Use Calcium Chloride to increase

Alkalinity

80-150ppm

200

Use Sodium Bicarbonate to increase

TDS

500

500-800ppm

1500

Use Pool Salt to increase Dilute to decrease –

Do not use Cyanuric Acid (Stabliser) as this will interfere with the oxidising capability of the Enviroswim

system

Complete and return your Warranty Registration Card NOW!!

1. Balance the water as per above. Ensure all Enviroswim switches are set to OFF and variable controls (Ioniser

and ORP) at minimum (fully counter-clockwise).

2. Turn on the pool pump so that water is owing through the filtration system

and the Enviroswim ionization/oxidation chamber and ultrasonic emitter

pipe. Set the left hand switch on the Enviroswim unit to MANUAL. Make

sure that the ionization/oxidation chamber is lled with water.

3. Turn on the right hand ON/OFF switch on the control box.

4. Turn the knob on the control box under the ORP meter slowly clockwise

until the ORP meter reads between 13 - 15 Amps.

5. Turn the ioniser switch to maximum. Run the unit for approximately 1 hour

per 1000 litres of water and test copper level.

6. Perform chemical tests to determine readings for pH, ORP, alkalinity,

copper, and calcium hardness then adjust accordingly. Refer to Operating

Manual for appropriate treatments.

7. Test the copper level and when in the range 0.2-0.4 ppm set the system

for the appropriate run time and adjust the Ioniser output to around 50%.

8. Startup is now complete. Refer to the operating manual for a guide on run

times. Remember every pool is dierent. Factors that will impact runtime

are location, bather load, season, type of cover and water temperature.

When can I use the pool?

It is OK to use the pool while the Copper levels are being established provided the EnviroSwim system is

processing the water continuously and the correct water balance (pH, alkalinity and hardness) is established.

The Oxidation process will treat organic matter and as water ows through the cell it will be being treated with

concentrated Copper and Silver ions. We recommend that the water is allowed to circulate at least once (allow

1 hour per 10,000 litres) before swimming.

1. Plan layout of components

a. Check component dimensions.

b. Conrm sequence of components in water ow.

c. Check cable lengths for control box location.

d. Power Supply

2. Conrm additional materials required

a. Pipe ttings and Pipe adhesive

b. Cable ties

c. Mounting Screws

3. Tools.

a. Pipe Saw

b. Drill and Bits

Return your Warranty Registration Card to ensure

 Warranty commences from installation rather than manufacturing date

 Seasonal Newsletter

 Rapid response to your questions

Balance Water

3. Commission

Balance Water

1. Plan 2. Install 3. Commission

1. Plan

IMPORTANT SAFETY INSTRUCTIONS

ATTENTION INSTALLER

This manual contains important information about the installation of this product. For complete instructions on

operation and safe use of this product refer to EnviroSwim ES-3 Operating Manual

 READ AND FOLLOW ALL INSTRUCTIONS. IMPORTANT SAFETY INSTRUCTIONS WARNING -

PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS

 To reduce the risk of injury, do not permit children to use this product unless they are closely WARNING –

supervised.

 When mixing acid with water, ALWAYS ADD ACID TO WATER, NEVER ADD WATER TO ACID. WARNING –

 There are no serviceable parts in the control box. Return to Enviroswim for service. WARNING –

 Do not operate electrolytic cell without proper ow or water circulation. A build-up of gases will WARNING –

result in hazardous conditions.

 Use of chemicals other than those recommended may be hazardous. Follow the Chemical CAUTION –

Manufacturer’s Instructions.

 This unit is for use with permanently installed pools. Do not use with storable pools. A CAUTION ––

permanently installed pool is constructed in or on the ground or in a building such that it cannot be readily –

disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled for

storage and reassembled to its original integrity.

 Some modern variable speed pumps have settings that produce inadequate water ow to either ll CAUTION –

the ES-3 wet cell or create sucient ow to eect the ES-3 processes. Do not allow these pumps to operate at

their minimum speed when the ES- is being operated. 3

READ ALL THESE INSTRUCTIONS

For advice phone 1300 888 457or email : info@enviroswim.com

What in the Box? ’s

 1 x Enviroswim Control Unit

 1 x Transparent water cell

o 1 x Titanium plate assembly

o 1 x Cu/Ag electrode

assembly

 Ultrasonic Emitter assembly

 Power Cable

 4 x 40mm to 50mm adapters

 Installation Guide (this guide)

 Operating Manual (A5)

 Warranty Registration Card

 Copper test kit

Review

instructions next

page

©Enviroswim 2014

2. Install

Pump and Filter Heating

Mains Power supply :

240V/50 Hz 10 Amp earthed

power supply appropriately

certied by a registered

electrician.

170 00.

140.00

150mm

80mm

135mm

370mm

100mm

200mm

670mm

Maintenance Access

77.00

35.00

25 00.

40.00

50.00

Inside Diameter

Allowance for cable

attachment

37 00.

Pool Pump –do not

exceed Max ratings

1.4

Metres

1.4

Metres

WARNING :

Ensure cell is mounted

oriented as shown.

Horizontal with water

ow from underneath.

Other orientations may

disable water level

sensor. Water Inow

should always be at

oxidiser end.

1.4

Metres

Ideal location suggestion. Ultrasonic Coil

may be anywhere in water ow with any

orientation.

WARNING : Do not

use primer on acrylic cell.

Actual Size Drilling Template

Termékspecifikációk

Márka:	Enviroswim
Kategória:	nincs kategorizálva
Modell:	ES-3

Szüksége van segítségre?

Ha segítségre van szüksége Enviroswim ES-3, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók nincs kategorizálva Enviroswim

Enviroswim ES-3 Útmutató

28 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

Roland SD-20 Útmutató

16 Október 2024

SilverCrest SRG 1300 C3 Útmutató

16 Október 2024

IFM TY0058 Útmutató

16 Október 2024

Thule Kit 186039 Útmutató

16 Október 2024

Blumfeldt Solidflor Útmutató

16 Október 2024

Dimplex QRAD200E Útmutató

16 Október 2024

DAS Audio AX-112-5 Útmutató

16 Október 2024

Ferplast Ergocomfort Freetime Útmutató

16 Október 2024

AEG MECK52 Útmutató

16 Október 2024

Black Diamond BD1121530000ALL1 Útmutató

16 Október 2024