Használati útmutató Emko ESM-3722

Emko Termosztát ESM-3722

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Emko ESM-3722 (2 oldal) a Termosztát kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

2.2PanelCut-Out

ESM- 77x35DINSizeHatcherController3722

InstructionManual.ENGESM-372201V0402/15

2.GeneralDescription

2.1FrontViewandDimensionsofESM-3722HatcherController

All order information of ESM-3722 Hatcher Controller are given on the table at above. User may form

appropriate device configuration from information and codes that at the table and convert it to the

ordering codes.Firstly, supply voltage then other specifications must be determined. Please fill the order

code blanks according to your needs. Please contact us, if your needs are out of the standards.

10.OtherInformations

WhenSET buttonispressedfor3

seconds,“P”ledturn.Ifprogramming

modeenteringpasswordisdifferent

from0,programmingmodeentering

screenwillbeobserved.

MainOperationScreen

ProgrammingScreen

Changethevaluewithincrement

anddecrementbuttons.

Press SET button for accessing to the

parameter value. Press increment

button for accessing to the next

parameter, press decrement button for

accessing to the previous parameter.

Presssetbuttonforsavingthe

parameter.

Press increment button for accessing to

the next parameter, press decrement

button for accessing to the previous

parameter.

ProgrammingMode

EnteringScreen

PressSET buttonfor

accessingtothe

passwordentering

PasswordEnteringScreen

Enterprogrammingmodeaccessing

passwordwithincrementand

decrementbuttons.

Note2: If programming mode accessing password is 0, only three parameters are accessible, and the

parameter values can be changed.

PressSET/OKbuttonfor

enteringthepassword.

Note1: Ifprogramming

modeaccessingpassword

is0, TemperatureUnit

screen isobserved

insteadofprogramming

screen

If no operation is performed in programming mode for 20 seconds, device turns to main

operation screen automatically.

DecimalSeparatorEnabling

SelectionScreen

5.5EnteringToTheProgrammingMode,ChangingandSavingParameter

3sec.

76mm/3inch

34,5mm/1.36inch

While button protection parameter value is 0,1,2 or

4 in main operation screen if engine button is pressed,

manual engine start will be active.When the button is

released the engine start will be passive and engine stops.

6. ManualStartofEggTrayRotatorOperationwithEngineButton

Note-1: If input type is selected PTC or NTC (B = 2, 3), Temperature sensor is given with the

device.For this reason, if input type is selected as PTC,sensor type (V = 0,1 or 2) or if input type is

selected as NTC, sensor type (V = 0, 3 or 4) must be declared in ordering information.

8.Specifications

PasswordEnteringScreen

TemperatureUnitSelection

ParameterValue

TemperatureUnitSelection

ParameterValue

8.Specifications

1.2.GeneralSpecifications

1.Preface

ESM3722-HT seriesHatchercontrollersaredesignedforcontrollinghatcherprocess.Device

canbeusedeasilywithPIDorOn-Offcontrolformandmanualstartofeggtrayrotatorproperties.

ESM-3722

PowerSupply

Input

Output

Humidification

EggTrayRotatorOutput

Alarm

1.1EnvironmentalRatings

-4DigitsforTemperatureDisplay

-4DigitsforHumidityDisplay

-TemperatureSensorInput

NTC,PTC,PT-100,0/2..10V,0/4..20mA orProNemMiniPMI-P

(Mustbedeterminedinorder.)

-HumiditySensorInput

0/2..10V,0/4..20mA orProNemMiniPMI-P

(Mustbedeterminedinorder.)

-4Output

HeatingControlOutput

EggtrayrotatorOutput

HumidificationControlOutput

AlarmControlOutput

-RelayorSSROutputs(Mustbedeterminedinorder.)

-SelectableTemparatureControl(PIDorON/OFF)

- Auto-TunePID

-Setvalueboundaries

-ManualStartoftrayrotatorfromfrontpanel

- Alarmparametreters

- Adjustableinternalbuzzeraccordingtothealarmsituations

-Passwordprotectionforprogrammingmode,

ESM- 77x35DINSize3722

DigitalHatcherController

3 416

MountingClamp

PanelSurface

(maximumthickness15mm/0.59inch)

Frontpanel

IP65Protection

65mm/2.56inch

6mm/0.24inch

110mm/4.33inch(min)

71mm/2.79inch

29mm/1.14inch

50mm/1.97inch(min)

Maximum15mm/0.59inch

230V ( %15)50/60HzV±

OptionalSupply

Voltage

-30V Z

115V ( %15)50/60Hz

24V ( %15)50/60Hz

Standard

DeviceType

Housing&Mounting

ProtectionClas

Weight

EnviromentalRatings

Storage/OperatingTemperature

Storage/OperatingHumidity

Installation

OvervoltageCategory

PollutionDegree

OperatingConditions

SupplyVoltageandPower

TemperatureSensorInput

:HatcherController

:76mmx34.5mmx71mmPlastichousingforpanel

Panelcutoutis71x29mm.

:Ip65atfront,Ip20atrear.

: Approximately0.2Kg

:Standart,indooratanaltitudeoflessthan2000meterswith

nonecondensinghumidity.

:-40 Cto+80 C/-30 Cto+80 C

:90%max.(Nonecondensing)

:Fixedinstallation

:II.

:II,officeorworkplace,noneconductivepollution

:Continuous

:115

:24

:10-30

:NTC,PTC,PT-100,0/2..10V 0/4..20mA or

ProNemMiniPMI-P

o o o o

Z Z,

230V ( %15)50/60Hz-1.5VA

V ( %15)50/60Hz-1.5VA

V 1.5WZ

Output Heating

YourTechnologyPartner

www.emkoelektronik.com.tr

Thankyouverymuchforyourpreferenceto

useEmkoElektronikproducts,pleasevisitour

webpagetodownloaddetailedusermanual.

OperatingTemperature:

Max.OperatingHumidity:

Altitude :

0to50°C

90%Rh(non-condensing)

Upto2000m.

Forbidden Conditions:

Corrosive atmosphere

Explosive atmosphere

Home applications (The unit is only for industrial applications)

A visual inspection of this product for possible damage occurred during shipment is recommended

before installation.

It is your responsibility to ensure that qualified mechanical and electrical technicians install this product.

If there is danger of serious accident resulting from a failure or defect in this unit, power off the system

and separate the electrical connection of the device from the system.

The unit is normally supplied without a power supply switch or a fuse. Use power switch and fuse as

required.

Be sure to use the rated power supply voltage to protect the unit against damage and to prevent failure

Keep the power off until all of the wiring is completed so that electric shock and trouble with the unit can

be prevented.

Never attempt to disassemble, modify or repair this unit. Tampering with the unit may results in

malfunction, electric shock or fire.

Do not use the unit in combustible or explosive gaseous atmospheres.

During putting equipment in hole on the metal panel while mechanical installation some metal burrs can

cause injury on hands, you must be careful.

Montage of the product on a system must be done with it’s fixing clamps. Do not do the montage of the

device with inappropriate fixing clamp. Be sure that device will not fall while doing the montage.

It is your responsibility if this equipment is used in a manner not specified in this instruction manual.

EMKO Elektronik warrants that the equipment delivered is free from defects in material and

workmanship. This warranty is provided for a period of two years. The warranty period starts from the

delivery date. This warranty is in force if duty and responsibilities which are determined in warranty

document and instruction manual performs by the customer completely.

Repairs should only be performed by trained and specialized personnel. Cut power to the device before

accessing internal parts.

Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of these

solvents can reduce the mechanical reliability of the device. Use a cloth dampened in ethyl alcohol or

water to clean the external plastic case.

1.3Installation

1.4Warranty

1.5Maintenance

1.6ManufacturerCompany

ManufacturerInformation:

Repairandmaintenanceserviceinformation:

EmkoElektronikSanayive Ticaret A.Þ.

DemirtaþOrganizeSanayiBölgesiKaranfilSk.No:616369BURSA/TURKEY

Phone:+902242611900

Fax:+902242611912

EmkoElektronikSanayive Ticaret A.Þ.

DemirtaþOrganizeSanayiBölgesiKaranfilSk.No:616369BURSA/TURKEY

Phone:+902242611900

Fax:+902242611912

TemperatureSensor

Input

HumiditySensorInput

0/2..10V,0/4..20mA or

ProNemMiniPMI-P

5.2 AlarmOutputGraphicsofESM-3722HT

Process High Alarm

OFF

Alarm

Output

Process Value

Process Low Alarm

OFF

Alarm

Output

ProcessValue

Deviation Band Alarm

OFF

Alarm

Output

(- AlarmSet)

=Process Set Value (Temperature or Humidity)

Deviation Range Alarm

OFF

Alarm

Output

ProcessValue

AlarmSet AlarmSet

(+AlarmSet)

(- AlarmSet) (+AlarmSet)

ProcessValue

5.3EggTrayRotatorOperationGraphicsofESM-3722HT

Egg Tray Rotator

Output Led

Egg Tray Rotator

Output

1- Screen Blinking Temperature Sensor failure . Sensor connection is wrong or there is no sensor

connection. While this message shown on this display,if buzzer function selection is 3, 5, 7 or 8

internal buzzer starts to operate.

5.4 FailureMessagesinESM3722HatcherController

2 Screen Blinking H Sensor failure . Sensor connection is wrong or there is no sensor

connection. While this message shown on this display,if buzzer function selection is 4, 6,7 or 8

internal buzzer starts to operate.

- umidity

NTCinputtype

PTCinputtype

Termoresistanceinputtype

Humidityinputtype

Accuracy

SensorBreakProtection

ControlForm

RelayOutputs

OptionalSSRDriverOutput

TemperatureDisplay

HumidityDisplay

LEDDisplays

InternalBuzzer

Upprovals

:NTC(10k @25°C)

:PTC(1000 @25°C)

:PT-100IEC751(ITS90)

:0/2..10V 0/4..20mA MiniPMI-P

:±1%offullscale

:Upscale

:PIDorON/OFF

:5A@250V atResistiveLoad(HeatingOutput)

:3 A@250V atResistiveLoad(Humidificating, Alarm

andEggtrayrotatorOutput

:Maximum30mA,Maximum15V

:8mmRed4digitLEDDisplay

:8mmGreen4digitLEDDisplay

:P (Green),%(Green), C(Red), F(Red), Alarm(Red),

HumidifierOutput(Red),EggtrayrotatorOutput(Red)

HeatingOutput(Red),

: 83dB

:,

Z Z

, orProNem

o o

7. AutoTuneMetod

Starting Auto Tune (Limit Cycle Tuning)

Operation by the user :

•Adjust t

•Adjust auto tune selection parameter ( = )

• In the main screen and Temperature value

are should alternately.

“Atun”

emperature control on/off or PID parameter

( =1)

Auto Tune method is used for determining PID parameters used by the device.

If Auto Tune operation is finished without any problem,

the device saves the new PID coefficients, calculated

using the previously found “T” and “B” values, to

memory and continue to run.

parameter is adjusted automatically.

Temperature

Value

Time

Heating

Output

Time

Cancelling Auto Tune (Limit Cycle Tuning) operation :

1 - If sensor breaks;

2 - If auto tune operation can not be completed in 8 hours ;

3 - If user adjusts parameter ;

4- During auto tune operation if the user changes the temperature control from pid to on/off;

5 - If process set value is changed while auto tune operation is being performed;

Auto tune is canceled. “Atun” is not displayed. Then, without doing any changes in PID

parameters, device continues to run with previous PID parameters.

3- In main operating screen if the upper display is blinking, it means that temperature alarm exits and

alarm output is active . 1 5if buzzer function selection is , or 8 internal buzzer starts to operate.

4- In main operating screen if the lower display is blinking, it means that humidity alarm exits and alarm

output is active . 2 6if buzzer function selection is , or 8 internal buzzer starts to operate.

B C D E FG HI /

UV W Z/

/ 0

PowerSupplyVoltageA

TemperatureSensorInputB Scale( )°C/°F

ESM-3722

(77x35DINSize)

-20°C/-4°F; 80°C/176°F

115V ( %15)50/60Hz-1.5VAV±

ProNemMiniPMI-P

PT 100,IEC751(ITS90)

PTC(Not-1)

5230V ( %15)50/60Hz-1.5VAV±

8 10-30V 1.5W

0°C/32°F;100°C/212°F

NTC(Not-1)

0°C/32°F;100°C/212°F

324V ( %15)50/60Hz-1.5VAV±

224V ( %15)50/60Hz-1.5VAW±

0%-100%

0/2..10VdcVoltageInput

50/4..20mA CurrentInput

HumiditySensorInputC Scale(%)

ProNemMiniPMI-P

0/2..10VdcVoltageInput

50/4..20mA CurrentInput

01 RelayOutput(3A@250V ,atResistiveLoad,1NO)V

HumidifierOutput

1RelayOutput(5 A@250V ,atResistiveLoad1NC,1NO)V

HeatingOutputE

2SSRDriveOutput(Maximum30mA,Maximum15V)

01 RelayOutput(3A@250V ,atResistiveLoad,1NO)V

EggTryRotatorOutputHI

1RelayOutput(3A@250V ,atResistiveLoad,1NO)V

AlarmOutput

Temp.SensorwhichisgivenwithESM-3722

0None

3NTC-M5L20.K1.5 (NTCProbethermoplasticmouldedwith

1.5mcableforcoolingapplication)

4NTC-M6L50.K1.5 (

)

NTCProbestainlesssteelhousingwith

1.5mcableforcoolingapplication

ProNemMiniPMI-P (2 for TemperatureandHumidity

application)

.5mcable

Customer

1PTC-M6L40.K1.5(PTC AirProbe1.5msiliconcable)

2PTCS-M6L30.K1.5.1/8”(PTCLiquidProbewith1.5msiliconcable)

Userdefined

ESM-3722

PTC,NTC,PT-100

0/2..10V,0/4..20mA or

ProNemMiniPMI-P

2.3PanelMountingandRemoving

5.ChangingandSavingTemperatureandHumiditySetValue

5.1Ch miditySetValue

MainOperatingScreen

WhenSET buttonpressed‘’S’’ ledwill

beactiveandtemperaturesetvaluewill

bedisplayed.

TemperatureSetValueScreen

Temperaturesetvaluecan

bechangedwithincrement

anddecrementbuttons.

WhenSET buttonpressed

temperaturesetvaluecanbesaved.

GoesHumiditySET

valuescreen.

Temperaturesetvalueparameter(Default=37.4 )

Temperaturesetvalue,canbeprogrammedbetweenminimumtemperaturesetvalue and

maximumtemperaturesetvalue .

°C

WhenSET buttonpressed

setvaluecanbesaved.

Humidity

Goesbackto

mainoperationscreen.

HumiditySetValue Screen

If no operation is performed in Humidity set value changing mode and temperature set value

changing mode for 20 seconds, device turns to main operation screen automatically.

HumiditySetValue Screen

5.1 ProgrammingModeParameterList

In ON/OFF control algorithm, temperature

value is tried to keep equal to set value by

opening or closing the last control element.

ON/OFF controlled system, temperature

value oscillates continuously. Temperature

value’s oscillation period or amplitude around

set value changes according to controlled

system. For reducing oscillation period of

temperature value, a threshold zone is formed

below or around set value and this zone is

named hysteresis.

Temperature Sensor Offset Parameter ( Default = 0 )

3.2DeviceLabelandConnectionDiagram

3.ElectricalWiringDiagram

3.1SupplyVoltageInputConnectionoftheDevice

4.FrontPanelDefinitionand AccessingtotheMenus

7 8 11

9 10

BUTTON DEFINITIONS

1. Increment Button :

2. Decrement, Silencing Buzzer Button :

3. Manual Start of Egg Tray Rotator Operation Button:

4. Set Button:

5.Alarm led :

6. Heating Output Led :

7.Celcius led :

8.Fahrenheit led :

9. Led :

10. Output Led :

11.Precent Sign ledi :

12.Program led :

** In main operation screen, press this button to change display temperature and humidity sensor

value.

** It is used to increase the value in the Temperature and Humidity Set screens and Programming mode.

** It is used to decrease the value in the Set screen and Programming mode.

** It is used to silence the buzzer.

When the button is released the

engine start will be passive and engine stops.

** In the main operation screen; if this button pressed for the first time, Temperature set value will be

displayed. Value can be changed using increment and decrement buttons. When Set button is pressed

again, value is saved and Humidty set value will be displayed next. Value can be changed using

increment and decrement buttons. When Set button pressed again, value is saved and returns back to

main operating screen.

** To access the programming screen; in the main operation screen, press and hold this button for 5

seconds.

** It is used to save value in the Set screens (Temperature or Humidity) and programming screen.

** This led indicates that heating output is active.

** Indicates that device is in C mode.

** Indicates that device is in F mode.

** This led indicates that is active.

** This led indicates that output is active.

** Indicates that device is in programming mode .

In the main operation screen, if this button pressed engine starts.

It is active when alarm statuses.

Egg Tray Rotator Output

Humidity

** Indicates that device is in Humidity Set screen.

LED DEFINITIONS

Egg Tray Rotator Output

Humidificating

230V CONNECTION DIAGRAMV

TemperatureControlSelectionParameterOn/OfforPID (Default=0)

On - Off selected.

PID selected.

PID - Proportional Control Parameter ( Default =50 )

This parameter value can be adjusted form 0 to 100.

PID - Integral Parameter( Default = 1000 )

This parameter value can be adjusted form 0 to 3600.

PID - Derivative Parameter ( Default = 250 )

This parameter value can be adjusted form 0 to 3600.

PID -Period Time Parameter ( Default = 1 )

This parameter value can be adjusted form 1 to 50 second.

HumiditySensorScaleSelectionParameter(Default=0)

Buzzer Function Selection Parameter( Default = 0 )

Button Protection Parameter ( Default = 0 )

Humidity Alarm Function Selection Parameter ( Default = 0 )

Humidity (Default = 0)

When power is first applied to the device, this time delay must be expired for activation of

Humidity alarm.

Alarm Delay After Power On Parameter

It can be adjusted from 0 to 99 minutes.

Humidity Set Maximum Parameter(Default =Maximum Value of Device Scale)

if humidity alarm is active, this parameter value can be adjusted from humidity alarm set

minimum parameter to maximum value of the device scale.

Alarm

Humidity (Default = 0)

Humidity

Alarm On Delay Time Parameter

AlarmOnDelay Timecanbedefinedwiththisparameter.Itcanbeadjusted

from0to99minutes.

Buzzer is inactive.

Buzzer is active during temperature alarm

Buzzer is active during humidity alarm

Buzzer is active during Temperature sensor failures.

Buzzer is active during Humidity sensor failures.

Buzzer is active during Temperature sensor failures or temperature alarm.

Buzzer is active during Humidity sensor failures or Humidity alarm.

Buzzer is active during Temperature sensor failures or Humidity sensor failures

or temperature alarm or humidity alarm.

There is no protection.

Temperature setvalue can not be changed.

Humidity set value can not be changed.

Manual engine start is not available.

Humidity set value and Temperature set value can not be changed

Humidity set value can not be change and Manual engine start is not available.

Temperature set value can not be change and Manual engine start is not

available.

Temperature set value and Humidity set value can not be changed. Also

Manual engine start is not available.

Humiditysetvalueparameter(Default=60%)

Humiditysetvalue,canbeprogrammedbetweenminimumHumiditysetvalue andmaximum

temperaturesetvalue .

1-Before mounting the device in your panel, make

sure that the cut-out is of the right size.

2-Insert the device through the cut-out. If the

mounting clamps are on the unit, put out them

before inserting the unit to the panel.

3- Insert the mounting clamps to the fixing sockets

that located left and right sides of device and

make the unit completely immobile within the

panel

1-Pull mounting clamps from left and right

fixing sockets.

2-Pull the unit through the front side of the

panel

Before starting to remove the unit

from panel, power off the unit and

the related system.

Make sure that the power supply voltage is the same indicated on

the instrument.

Switch on the power supply only after that all the electrical

connections have been completed.

Supply voltage range must be determined in order. While installing

the unit, supply voltage range must be controlled and appropriate

supply voltage must be applied to the unit.

There is no power supply switch on the device. So a power supply

switch must be added to the supply voltage input.

Power switch must be two poled for seperating phase and neutral,

On/Off condition of power supply switch is very important in

electrical connection.

External fuse that on power supply inputs must be on phase

connection.

External fuse that on power supply inputs must be on (+)

connection.

PowerSupplyInput

External

Fuse

(1A T)

Note-1

Supply

Switch

7 8

Supply Voltage

230V ( %15) 50/60Hz ,

115V ( %15) 50/60Hz ,

24V ( %15)50/60Hz ,

24V ( %15) 50/60Hz ,

10...30 V 1.5 W

Mustbedeterminedinorder.

OFF

Temperature

Control

Output

Set

thSt

Time

thSt

Time

5 6

9 10

7 8

TemperatureSetValueScreen HumiditySetValue Screen

Humiditysetvaluecanbe

changedwithincrementand

decrementbuttons.

RelayOutputs

135

468

7910

P/N: ESM-3722

PowerSupplyVoltage

230V ( %15) 50/60Hz ,

115V ( %15) 50/60Hz,

24V ( %15) 50/60Hz ,

10...30 V 1.5 W

11 12

TemperatureSensorInput

NTC,PTC,PT-100or

ProNemMiniPMI-P

HumiditySensorInput

0/2..10V,0/4..20mA or

ProNemMiniPMI-P

Mustbedeterminedinorder.

7 8 9 10

3x3 @250VA V

5A @250VV

230 V ±15%

50/60Hz-1.5VA

2 3 41

ALARM

HUM.

5 6 11 12

14A TFuse

ENGINE

HEAT

7 8 9 10

3x3 @250VA V

5A @250VV

230 V ±15%

50/60Hz-1.5VA

2 3 41

ALARM

HUM.

5 6 11 12

14A TFuse

ENGINE

HEAT

PTC Temperature and 0/4..20mA Humidity Sensor Input connection

VCC

GND

SCL

SDA

ProNem Mini PMI-P Temperature and Humidity Sensor Input Connection

Note: If this parameter is select 0, PID parameters ( , , , , ) will be not observed.

If this parameter select 1, parameter will be not observed.

Auto Tune (Limit Cycle Tuning) Selection Parameter ( Default = )

Device does not do(Limit cycle Tuning) operation.

Device does operation.

HysteresisParameterforTemperature(Default=0.1°C)

From 1 to 10°C for NTC,PTC, PT-100 (0°C, 100°C) ,From 1 to 18°F for NTC,PTC ,PT-100

(32°F, 212°F),From 0.1 to 10.0°C for NTC, PTC, PT-100 (0.0°C,100.0°C), From 0.1 to

18.0°F for NTC, PTC, PT-100 (32.0°F,212.0°F) ,From 1 to 10°C for ProNem Mini PMI-P

(-20°C, 80°C) ,From 1 to 18°F for ProNem Mini PMI-P (-4°F,176°F), From 0.1 to 10.0°C for

ProNem Mini PMI-P (-20.0°C,80.0°C), From 0.1 to 18.0°F for ProNem Mini PMI-P

(-4.0°F,176.0°F).

Minimum Temperature Set Value Parameter ( Default = 10.0°C)

Temperature set value can not be lower than this value. This parameter value can be

adjusted from minimum value of device scale to maximum temperature set value

parameter

Maximum Temperature Set Value Parameter ( Default = 40.0 °C )

Temperature set value can not be greater than this value.

This parameter value can be adjusted from minimum temperature set value parameter

to maximum value of the device scale.

From -10 to 10°C , NTC,PTC , PT-100 (0°C, 100°C)

From -18 to 18°F, NTC,PTC , PT-100 (32°F, 212°F)

From -10.0 to 10.0°C , NTC ,PTC , PT-100 (0.0°C,100.0°C)

From -18.0 to18.0°F NTC, PTC , PT-100 (32.0°F,212.0°F)

From -10 to 10°C ,ProNem Mini PMI-P ( -20°C, 80°C )

From -18 to 18°F,ProNem Mini PMI-P ( -4°F, 176°F )

From -10.0 to 10.0°C, ProNem Mini PMI-P ( -20.0°C, 80.0°C )

From -18.0 to18.0°F, ProNem Mini PMI-P ( -4.0°F,176.0°F )

0..10V 0..20mAZ Zor

2..10V 4..20mAZ Zor

(1) (2)

(2)(1)

It is valid, if the device type 0/2...10V

It is valid, if the device type 0/4...20mA

Humidity Sensor Input.

Humidity Sensor Input .

(1)

(2)

Analogue input range is determined with this parameter.

Note : parameter ProNem Mini PMI- type device are not observed.P

HysteresisParameterforHumidity(Default=1)

From 1 to 10 for Humidity Sensor (0%RH, 100%RH)

From 0.1to 10.0 for Humidity Sensor (0.0%RH,100.0%RH)

In ON/OFF control algorithm,

value is tried to keep equal to set value by

opening or closing the last control element.

ON/OFF controlled system, temperature

value oscillates continuously. Temperature

value’s oscillation period or amplitude

around set value changes according to

controlled system. For reducing oscillation

period of temperature value, a threshold

zone is formed below or around set value

and this zone is named hysteresis.

Humidity

OFF

Humidity

Control

Output

Set

hhSt

Time

hhSt

Time

Maximum Humidity Set Value Parameter (Default = Maximum Value of Device Scale)

This parameter value can be

adjusted from minimum humidity set value parameter to maximum value of the

device scale.

Humidity set value can not be greater than this value.

Minimum Humidity Set Value Parameter (Default = Minimum Value of Device Scale)

set value can not be lower than this value. This parameter value can be adjusted

from minimum value of device scale to maximum set value parameter

Humidity

Sensor Offset Parameter ( Default = 0.0 )Humidity

From -10 to 10 for Humidity Sensor (0%RH, 100%RH)

From -10.0 to 10.0 for Humidity Sensor (0.0%RH,100.0%RH)

Timeof AutomaticEggTrayRotator (Default=00:00)

Thisparametervaluecanbeadjustedform00:00to99:00minute/second.

Repeatcycleof AutomaticEggTrayRotator (Default=00:00)

Thisparametervaluecanbeadjustedform00:00to24:00hour/minute.

Alarm Output Function Selection Parameter ( Default = 0 )

Alarm is inactive.

Alarm-Temperature sensor failures.

Alarm-Humidity sensor failures.

Alarm-Temperature or Temperature sensor failures.

Alarm-Humidity or Humidity sensor failures.

Alarm-Temperature sensor failures or Humidity sensor failures.

Alarm-Temperature or Humidity or Temperature sensor failures or Humidity

sensor failures.

Note : if parameter value is 3 or 6 , , , , , or parameters are

observed.

Note : if parameter value is 4 or 6 , , , , , or parameters are

observed.

Temperature Alarm Set Parameter

Thisparametervaluecanbeprogrammedbetweentemperatureminimumalarmset

parameterandtemperaturealarmsetmaximum parameter.

( Default = 50.0 °C )

Temperature Alarm Function Selection Parameter ( Default = 0 )

Process High alarm selected.

Process Low alarm selected.

Deviation Band alarm selected.

Deviation Range alarm selected.

Alarm Set Maximum Parameter ( Default = Maximum Value of Device Scale)

if temperature alarm is active, this parameter value can be adjusted from temperature

alarm set value parameter to maximum value of the device scale.

Alarm Set Minimum Parameter (Default = Minimum Value of Device Scale)

if temperature alarm is active, this parameter value can be adjusted from minimum value of

device scale to temperature alarm set maximum parameter value.

Temperature Alarm Parameter

This parameter value can be adjusted form 0 to %50 of the device scale.

Hysteresis ( Default = 0)

Temperature AlarmOnDelayTimeParameter

Temperature AlarmOnDelay Timecanbedefinedwiththisparameter.Itcanbe

adjustedfrom0to99minutes.

(Default=0)

Temperature Alarm Delay After Power On Parameter

It can be adjusted from 0 to 99 minutes.

( Default = 0)

When power is first applied to the device, this time delay must be expired for activation of

temperature alarm.

Process High alarm selected.

Process Low alarm selected.

Deviation Band alarm selected.

Deviation Range alarm selected.

Humidity AlarmSetParameter

Thisparametervaluecanbeprogrammedbetweenhumidityminimumalarmset

parameterandhumidityalarmsetmaximum parameter.

(Default=50)

Humidity Set Minimum Parameter(Default =Minimum Valueof Device Scale)

if humidity alarm is active, this parameter value can be adjusted from minimum value of

device scale to humidty alarm set maximum parameter value.

Alarm

Humidity Alarm Parameter

This parameter value can be adjusted form 0 to %50 of the device scale.

Hysteresis ( Default = 0)

Buzzer ActiveTime

Ifbuzzerfunctionselectionparameter

Buzzeractivetimecanbedefinewiththisparameter.Itcanbeadjustedfrom1to99

minutes.Whenthisparameteris1,ifdecrementbuttonispressed, isobserved.In

thisconditionbuzzerisactivetillbuzzersilencebuttonispressed.

(Default= )

value=0,thisparameterisnotobserved.

Note-1: External Fuse is recommended

WHITE

YELLOW

BROWN

GREEN

ProNemMini

PMI-P

BLACK

Shield

Note: (Black)pinmustbeconnectedtonumber10(GND)oftheterminalblock.Shield

P/N:ESM-3722-5.2.5.0.1/01.01/1.0.0.0

7 8

3x3A@250V V

5A @250VV

230 V ±15%

50/60Hz -1.5VA

2 3 41

ALARM

PTC

5 6

ENGINE

HEAT

L N NNN N

0/4-20mA

HUM.

INPUT

TEMP.

INPUT

9 10 11

P/N:ESM-3722-5.6.6.0.1/01.01/1.6.6.0

7 8 9 10

3x3A@250V V

5A @250VV

230 V ±15%

50/60Hz-1.5VA

2 3 41

ALARM

5 6

ENGINE

11 12

HEAT

L N NNN N

HUM.

ProNemMiniPMI-P

WHITE

BROWN

YELLOW

GREEN

VCC

GND

SCL

SDA

5.1 ProgrammingModeParameterList

Decimal Seperator Enabling Parameter ( Default = 0 )

None.

Only Temperature parameters with decimal seperator.

TemperatureUnitSelectionParameter (Default=0)

°C selected.

°F selected.

Only Humidity parameters with decimal seperator.

Only Temperature and Humidity parameters with decimal seperator.

Note : When value of or parameters are changed , the values of , , , ,

, , , , , , , , , , , , and parameters

should be changed accordingly.

0..10V veya 0..20mAZ Z

2..10V veya 4..20mAZ Z

Temperature SensorScaleSelectionParameter(Default=0)

(1) (2)

(2)(1)

Analogue(T inputrangeisdeterminedwiththisparameter.emperature)

Temperature

SensorScaleLowLimitParameter:(Default=0)

It can be adjusted from -1999 to ( -1). At this value analogue input becomes;

If =0,accordingtothedevicetype0V 0mA

If =1,accordingtothedevicetype2V 4mA

Z Z

(1) (2)

Temperature

SensorScaleHighLimitParameter:(Default=100)

Itcanbeadjustedfrom( +1)to9999. Atthisvalueanalogueinputbecomes;

According to the device type 10V 20mAZ Z

(1) (2)

Note : , parameters are shown, if the Temperature sensor analogue input type is selected .

Note : , and parameters are shown, if the Temperature sensor input type

( ) is selected.

analogue

0/2..10V or 0/4..20mA

ESM-3722

ü ü

ESM-3722

ü ü

ESM-3722

ESM-3722 ESM-3722

Programming Mode Accessing Password

It is used for accessing to programming mode. It can be adjusted from 0 to 9999. If it is 0,

password is not entered for accessing to the parameters. When the password screen is not

set as “12” , If the user enters ‘12’ in password screen and parameters are

accessed and they can changed.

( Default = 0 )

Termékspecifikációk

Márka:	Emko
Kategória:	Termosztát
Modell:	ESM-3722

Szüksége van segítségre?

Ha segítségre van szüksége Emko ESM-3722, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Termosztát Emko

Emko Eco Light Útmutató

1 Szeptember 2024

Emko ESM-4900 Útmutató

25 Augusztus 2024

Emko CHANNEL8N Útmutató

25 Augusztus 2024

Emko ESM-4920 Útmutató

25 Augusztus 2024

Emko ESM-3722 Útmutató

25 Augusztus 2024

Emko ESM-9945-N Útmutató

25 Augusztus 2024

Útmutatók Termosztát

Legújabb útmutatók Termosztát

Siemens RDG100T Útmutató

16 Október 2024

Junkers TA 21E Útmutató

14 Október 2024

Salus CT100 Útmutató

7 Október 2024

Dimplex 6181 Útmutató

7 Október 2024

Danfoss RA 2982 Útmutató

6 Október 2024

Bosch Radiator thermostat II Útmutató

5 Október 2024

Danfoss RET 230L Útmutató

5 Október 2024

Theben RAM 811 Top - 811 9 901 Útmutató

5 Október 2024

Renkforce MH-850T Útmutató

5 Október 2024

Siemens DESIGO RXA Útmutató

5 Október 2024