Használati útmutató Elo ECMG4

Elo nincs kategorizálva ECMG4

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Elo ECMG4 (30 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/30
USER MANUAL
Elo Touch Solutions
Interactive Digital Signage (IDS) ECMG4 For
IDS 6553L
User Manual Elo Computer Module –
UM600 Rev. A, page 2 of 337 31
Copyright © 2019 Elo Touch Solutions, Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form
or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.
Disclaimer
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) makes no representations or
warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the
right to
revise this publication and to make changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or changes.
Trademark Acknowledgments
Elo, Elo (logo), Elo Touch, and Elo Touch Solutions are trademarks of Elo and its Affiliates. Windows is a trademark of Microsoft Corporation.
User Manual Elo Computer Module –
UM600 Rev. A, page 3 of 337 31
Table of Contents
Section 1: Introduction ............................................................................................................................................................................................................................... 4
Section 2: Unpacking 5................................................................................................................................................................................................................................
Section 3: Computer Module Installation 6..................................................................................................................................................................................................
Section 4: Technical Support .................................................................................................................................................................................................................. 18
Section 5: Safety & Maintenance ............................................................................................................................................................................................................ 20
Section 6: Regulatory Information ........................................................................................................................................................................................................... 21
Section 7: Warranty Information .............................................................................................................................................................................................................. 26
User Manual Elo Computer Module –
UM600 Rev. A, page 4 of 337 31
Section 1: Introduction
Product Description
Interactive Digital Signage Elo Computer Module Generation 4 (ECMG4) is designed to slide into the bay on the back of the IDS -Series touch displays, 53
without any effect on the monitor’s form factor or requiring any extra cabling. By combining the two, you can transform your Interactive Digital Signage
Touch Display into an a - -o touchcomputer. ll In ne
Precautions
Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit and prevent risks to user safety.
This manual contains information that is important for the proper setup and maintenance of the Computer Module. Before setting up and powering on your
new Computer Module, read through this manual, especially the Computer Module Installation chapter.
User Manual Elo Computer Module –
UM600 Rev. A, page 5 of 337 31
Section 2: Unpacking
Unpacking the ECMG4
Check that the following items are present and in good condition:
•
Computer Module
•
Quick Install Guide
•
Two antennas
User Manual Elo Computer Module –
UM600 Rev. A, page 6 of 337 31
Section 3: Computer Module Installation
Installation
1. Slide the ECM down into the docking bay and slide it in to engage the connector. Tighten the locking screw with a philips screwdriver.
Locking
Screw
User Manual Elo Computer Module –
UM600 Rev. A, page 7 of 337 31
Connector Panel & Interfaces
Touchmonitor & Computer Module Connections
1. Once the Computer Module has been installed, connect the AC power cable between the touchmonitor’s POWER IN connector and the AC power
source.
a. NOTE: Computer Module can be installed when the AC power cable is connected (Hot pluggable). Do not remove the Computer Module
unless it is completely shut off.
2. Make any desired connections to the Computer Module connector panel.
3. Press the touchmonitor’s power button to turn on the Computer Module.
Operating System Setup Windows 10 –
The initial setup of the operating system takes approximately five minutes. Additional time might be needed for specifying operating system configurations.
During installation, you will be prompted to enter user information. This can be done via touch and the on screen keyboard or you can connect a USB
mouse and keyboard to fill in the required information.
To set up the Windows 10 OS for the Computer Modu , turn on the touchcomputer and follow the instructions on the screen.le
USB p7-x4
HDMI
Ethernet
User Manual Elo Computer Module –
UM600 Rev. A, page 8 of 337 31
Selecting the Language
Windows will prompt you to select your language of preference. See reference image below.
Agreeing to Terms and Conditions
You will be prompted to agree to the Windows license terms. Click “I Accept” to continue.
User Manual Elo Computer Module –
UM600 Rev. A, page 9 of 337 31
Choosing the Windows Settings
You will be prompted to select the Windows settings
Creating Your Account
You will be prompted to create a Username and Password. Once set up, click “Finish to complete Setup. See reference image below.”
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 10 31
Operating System Setup No OS –
No Operating System (No OS) units will require an operating system to be installed on them.
Load your operating system of choice onto the Computer Module.
Once you have installed an OS image onto your computer, allow the system to automatically install all the available drivers.
You can download the latest Elo Touch Driver from www.elotouch.com and proceed to install that driver onto the computer.
Installing Touchscreen Technology Software Drivers on Elo Computer Modules
Visit the Elo Touch Solutions website www.elotouch.com for:
•
The latest versions of our touch drivers
•
Additional touch driver information
•
Detailed touch driver installation guides
•
Touch drivers for other operating systems
Download and install the required touch driver from www.elotouch.com.
Creating the Recovery Flash Drive
All Windows 10 Computer Modules come with the built-in Elo Restore Utility on the Windows Desktop. The utility allows for creation of a recovery flash
drive based on the purchased operating system. Please create your recovery flash drive immediately. In the event that the HDD/SSD recovery partition
accidentally gets deleted or becomes inaccessible, you can use the recovery flash drive to recover your system.
The following procedures demonstrate how to create a recovery flash drive.
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 11 31
1. Right- Run as administrator. click on the EloRestoreUtility icon on the Desktop and select “ ”
2. Click “Start” button to begin the process.
3. Once completed, you will see a pop-up window that will prompt you to insert a blank flash drive to any of available USB ports on your system. the
(For Windows , use a flash drive with at least GB of space available) 10 32
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 12 31
4. After the flash drive is plugged in, you will see the below window. Click “Format Drive” to continue the process. PLEASE NOTE THAT THIS WILL
ERASE ALL DATA CONTAINED IN THE FLASH.
5. Click “Create Restore Media” to proceed. This step will take about 10-20 minutes, depending on your system configurations and flash drive
performance.
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 13 31
6. Once the message “Creation Restore Media success…” appears, remove the flash drive and click “Exit” to exit the program.
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 14 31
Recovering the System to factory defaults
If for any reason the touchcomputer’s operating system needs to be recovered TO FACTORY SETTINGS, you can recover your system by following
procedures below. PLEASE NOTE THAT ALL CUSTOMER SETTINGS AND DATA WILL BE LOST DURING THIS PROCESS. Please be sure to backup all
data, settings, and customer-installed software before proceeding.
1. Power off your system.
2. Power on your system.
3. Plug in the USB drive (created in the previous section) to the computer module.
4. In case the system is crashed and you have to use the recovery flash drive, reboot the system and press F7 several times to enter Device Boot
Menu. Then, choose “boot from flash drive”. When the following UI is presented, click “Install Recovery Solution” button.
5. Follow the on-screen instructions to complete the installation process and then exit the program.
i. Note: All data will be deleted during the recovery process. User should back up files when necessary. Elo Touch Solutions does not accept
liability for lost data or software.
ii. Note: The end user must adhere to Microsoft's Licensing Agreement
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 15 31
Recovering the Operating System
1. Select Restore OS . The system will automatically test your hardware. Once the process completes, click the Start button to perform the “ ” “ ”
system recovery function.
2. Please back up your data before performing the recovery process. The following process will reformat the primary hard drive.
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 16 31
3. Once completed, click the Close button. The system will return to the main menu of the Elo Recovery Solution. Click the Exit button to restart your “ ” “ ”
system.
All data is deleted during the recovery process. The user should back up files when necessary. Elo Touch Solutions does not accept liability for lost data
or software.
The end user must adhere to Microsoft's Licensing Agreement.
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 17 31
Software Solutions
The following software solutions are can be used to enhance the experience when using the Elo Computer module with the IDS 6553 or 5553L
monitor.
Qwizdom Octopus Can be used for whiteboard applications and presentations. The user guide for this software is available at –
https://qwizdomoktopus.com/user-guide/
DisplayNote Montage n be used for wireless presentations and collaboration. The details for this software is available at –Ca
https://www.displaynote.com/solutions/montage
AirServer Can be used to wireless cast devices to the ECMG4 + IDS6553 Display. Details for the AirServer Application is available at –
https://www.airserver.com/WindowsDesktop
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 18 31
Section 4: Technical Support
If you are experiencing trouble with your Computer Module, refer to the following suggestions.
If the problem persists, please contact your local dealer or contact Elo Touch Solutions Customer Service.
Solutions to Common Problems
Problem
Suggested Troubleshooting
The Computer Module does not turn on
when the power button is pressed.
Disconnect the AC power cable and verify that the Computer Module is properly installed
Reconnect the AC power cable and turn on the system
Audio cannot be heard on external devices
Ensure that the proper source is selected on the monitor OSD.
Confirm that the correct audio output port is selected on the Windows OS.
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 19 31
Technical Assistance
See this user manual’s last page for worldwide technical support phone numbers.
Technical assistance for Computer Modules running Windows OS are also available on the computer in the Support Information section of the Systems
Properties menu. The Systems Properties menu can be accessed by:
•
Right-clicking the My Computer icon and selecting Properties from the drop-down menu, or
•
Clicking the Start button; go to the Settings -> Control Panel menu and selecting the System icon
Technical Specifications
visit www.elotouch.com/products
for technical specifications for this device
Support
visit www.elotouch.com/support
for technical support
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 20 31
Section 5: Safety & Maintenance
Safety
•
To avoid risk of electric shock, follow all safety notices and do not disassemble the touchmonitor. They are not user-serviceable.
•
The slots located on the sides and top of the touchmonitor case are for ventilation. Do not block or insert anything inside the ventilation slots.
•
Ensure that your installation allows touchmonitor to meet specified environmental conditions below:
Environmental conditions for transportation and storage
Temperatur e:
Operating 0°C to 40°C
Storage/Transportation -20°C to 60°C
Humidity (non-condensing):
Operating 20% to 80%
Storage/Transportation 10% to 90%
Altitude:
Operating 0 to 3,000m
Storage/Transportation 0 to 12,192m
Caution
There is risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries at the end of its useful life according to local laws and
regulations.
Waste Electrical & Electronic Equipment Directive (WEEE)
This product should not be disposed of with household waste. It should be deposited at a facility that enables recovery and recycling.
Elo has put in place recycling arrangements in certain parts of the world. For information on how you can access these arrangements, please visit
www.elotouch.com/e-waste-recycling-program/.
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 21 31
Section 6: Regulatory Information
Electrical Safety Information
Compliance is required with respect to the voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different
power source than those specified herein will likely result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not
followed.
There are no operator serviceable parts inside this equipment. There are hazardous voltages generated by this equipment which constitute a safety
hazard. Service should be provided only by a qualified service technician.
Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment to mains power.
Emissions and Immunity Information
Notice to Users in the United States:
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Notice to Users in Canada:
This equipment complies with the Class A limits for radio noise emissions from digital
apparatus as established by the Radio Interference Regulations of Industrial Canada.
CAN ICES3(A)/NMB3(A)
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 22 31
Notice to Users in the European Union: Use only the provided power cords and interconnecting cabling provided with the equipment. Substitution of
provided cords and cabling may compromise electrical safety or CE Mark Certification for emissions or immunity as required by the following standards:
This Information Technology Equipment (ITE) is required to have a CE Mark on the Manufacturer’s label which means that the equipment has been tested
to the following Directives and Standards: This equipment has been tested to the requirements for the CE Mark as required by EMC Directive 20 / / EU 14 30
as indicated in European Standard EN 55032 Class A and the Low Voltage Directive 20 /35 U as indicated in European Standard EN 60950-1. 14 /E
General Information to all Users: This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to this
manual the equipment may cause interference with radio and television communications. There is, however, no guarantee that interference will not occur in
any particular installation due to site-specific factors.
1.
In order to meet emission and immunity requirements, the user must observe the following:
a.
Use only the provided I/O cables to connect this digital device with any computer.
b.
To ensure compliance, use only the provided manufacturer’s approved line cord.
c.
The user is cautioned that changes or modifications to the equipment not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
2.
If this equipment appears to cause interference with radio or television reception, or any other device:
a.
Verify as an emission source by turning the equipment off and on. If you determine that this equipment is causing the interference, try to
correct the interference by using one or more of the following measures:
i.
Move the digital device away from the affected receiver.
ii.
Reposition (turn) the digital device with respect to the affected receiver.
iii.
Reorient the affected receiver’s antenna.
iv.
Plug the digital device into a different AC outlet the digital device and receiver are so the on different branch circuits.
v.
Disconnect and remove any I/O cables that the digital device does not use. (Unterminated I/O cables are a potential source of high
RF emission levels.)
vi.
Plug the digital device into only a grounded outlet receptacle. Do use not AC adapter plugs. (Removing or cutting the line cord
ground may increase RF emission levels and may also present a lethal shock hazard to the user.)
If you need additional help, consult your dealer, manufacturer, or an experienced radio or television technician.
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 23 31
Agency Certifications
The following certifications and marks have been issued or declared for this monitor:
•
Europe CE
•
Australia RCM
•
Canada CUL, IC
•
Europe CE
•
Japan VCCI
•
United States FCC, UL
•
International CB
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 25 31
Explanation of Markings
In accordance with the SJ/T11364 requirement, electrical and electronic products are marked with the following pollution control logo.
The Environment-Friendly Use Period for this product is 10 years. The product will not leak or mutate under normal operating conditions listed below, so
that the use of this electronic information product will not result in any severe environmental pollution, any bodily injury, or damage to any assets.
Operating Temperature: 0-40 / Humidity:20%-80% (non-condensing).
Storage Temperature: -20~60 / Humidity:10%~90% (non-condensing).
It encouraged recommended that product packaging recycled and reused according local laws. is and be to
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 26 31
Section 7: Warranty Information
For warranty information, go to http://support.elotouch.com/warranty/
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 27 31
Notes
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 28 31
User Manual Elo Computer Module –
UM600 Rev. A, page of 337 29 31
Notes

Termékspecifikációk

Márka: Elo
Kategória: nincs kategorizálva
Modell: ECMG4

Szüksége van segítségre?

Ha segítségre van szüksége Elo ECMG4, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva Elo

Elo

Elo 19R Útmutató

20 Augusztus 2024
Elo

Elo 19MR Útmutató

20 Augusztus 2024
Elo

Elo 15D2 Útmutató

20 Augusztus 2024
Elo

Elo Tablet Útmutató

18 Augusztus 2024
Elo

Elo ECMG3 Útmutató

15 Augusztus 2024
Elo

Elo ECMG4 Útmutató

15 Augusztus 2024
Elo

Elo Backpack Útmutató

15 Augusztus 2024
Elo

Elo Temperature Sensor Pro Útmutató

14 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
Soundstream

Soundstream VRN-64HBL Útmutató

10 Április 2025
Panasonic

Panasonic Lumix DMW-AC11 Útmutató

10 Április 2025
Planet

Planet PWR-240-48 Útmutató

9 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
Alpine

Alpine DP2-40C-BC Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025