Használati útmutató Edox CO-1 Chronograph 10221-3-NIN
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Edox CO-1 Chronograph 10221-3-NIN (24 oldal) a óra kategóriában. Ezt az útmutatót 15 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/24
HTTPS://ALPHARD.AUDIO
FOUR-CHANNEL AMPLIFIERS
ЧЕТЫРЕХКАНАЛЬНЫЕ УСИЛИТЕЛИ
OWNER’S MANUAL
РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ
MLA-40 8 0 M L A-4120
CLASS AB
2
C O N T E N T S EN
1. Introduction
2. Safety instructions
3. Typical installation sequence
4. Selection of the diameter of power cables and speaker cables
5. Wiring diagrams
6. Connection methods
7. Specifications
8. Possible faults and their solutions
9. sBox content
10. Warranty and maintenance info
11. Information on disposal of the electrical and electronic equipment (for the European countries
with separate waste collection)
3
EN
1 . I N T RO D U C T I O N
1. Make sure that your vehicle has a 12V DC electrical system with negative grounding. Before installing the amplifier in cars, trucks or
buses, check the battery voltage.
2. Check the state of on-board power supply of your vehicle, the battery and the alternator. When the engine is running, depending on
the ambient temperature, the voltage to be outputted by the alternator must be within the range of 14 to 14.7 V. Open circuit voltage
(OCV) of the battery must be within the range of 12.5 to 13 V. Make sure that the rated current of the alternator and the battery capacity is
enough to provide increased consumption.
For example, for the power of the amplifier 1000 W, the rated current of the alternator is required at the rate of 1000 W / 13 V = 77
amperes. A more powerful amplifier requires a more powerful alternator as well as an additional battery.
3. Do not place the amplifier in the engine compartment and also in the places exposed to water, moisture, dust or dirt.
4. Never stretch the cables outside of the car and near the moving parts of the car. This can lead to destruction of the insulating layer,
short circuit and fire.
5. The amplifier should be installed in areas of the car where the temperature varies from 0 °C (32 °F) to 55 °C (131 °F). The amplifier
should be in a place with a good air circulation. The horizontal position of the amplifier is the best way to install.
6. During the operation the amplifier may be heated up to 80 °C (176 °F). Before you touch it, make sure it is not overheated that may
be dangerous.
7. To improve the cooling of the amplifier, it is recommended to clean periodically the heatsink from dust. When cleaning the heatsink
strong solvents should not be used as they may damage the amplifier. Do not use compressed air, because solids can penetrate inside the
amplifier. Cleanings best done with wet towels or cloth.
8. Make sure that the location of the amplifier does not violate the proper operation of mechanical and electrical devices of the vehicle.
9. Make sure that during the installation and connection of the battery, the power cables are not shorted.
10. When performing plumbing, drilling or cutting works with the car, make sure that there is no wiring, brake lines, fuel pipe or other
structural elements under the place of work. Follow the safety rules! Use protective glasses and gloves.
11. To protect the wires use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies close to the
parts exposed to heat.
12. Make sure that all the cables are fixed over the entire length. Also make sure that their outer protective shell is non-combustible.
Use a clamping screw to secure the positive and negative cables next to the appropriate terminals of the amplifier.
13. Select a diameter of the power cable in accordance with the power of the amplifier and the recommendations provided here.
Power cables are extremely important since they directly affect the system damping factor and sound quality. The cables to the battery
must be in the copper crimp terminals pressed with the help of a hydraulic press, and well fixed to the battery terminals.
14. To avoid accidental damage, keep the amplifier in its original packaging prior to installation.
15. Use high-quality copper speaker and power cables.
CAUTION!!! High sound pressure can damage your health!
Please use the common sense when controlling volume!
2 . S A F E T Y I N S T R U C T I O N S
3 . T Y P I C A L I N S T A L L A T I O N S E Q U E N C E
1. Before installing the amplifier disconnect the battery from the electrical system.
2. To connect the amplifier it is necessary to stretch the power cable from the location of the battery to the place of installation
of the amplifier. Select the power cable with the appropriate regulations in AWG (see Table: Selection of the diameter of the
power cables)
3. Connect the power supply with the correct polarity. Connect all (+) terminals of the amplifier to the cables stretching from
the positive terminal of the battery and all (-) terminals of the amplifier – to the cables stretching from the negative terminal of the
battery.
4. Place the fuse holder for each positive cable within 40 cm from the positive terminal of the battery and connect one end of
the power cable to the holder after connecting the other end to the amplifier. Do not install the fuse(s).
5. Route all signal cables next to each other and separately from the power cables.
6. Connect the wires of RCA input. The input signal power must be between 0.2 V and 6 V.
7 To connect the power wire supply is necessary to use special. power cables.
8. Fasten the amplifier properly when installing it in the vehicle. If the component is disconnected during driving, it may cause
serious damage to the passengers of the vehicle or another vehicle. It is not recommended to screw the amplifier directly to the
metal it can lead to distorsions at the signal outputs.
9. After installation is complete, check the wiring of the system and make sure that all connections have been made correctly.
Before installing the fuses, disconnect the positive lead from the battery and then install the fuse in the fuse holder. Using the
light bulb 12 V 21 W, connect the positive lead to one contact of the bulb and the other contact of the bulb to the positive
terminal of the battery.
When properly connected, the bulb must briefly light up and go out. Now you may connect the positive lead to the (+) of the
battery. If the light does not go out, then something is wrong. This will prevent damage to the amplifier in case of reverse polarity
and unwanted sparks when connecting. Install the rest of the fuses.
10 . To activate the amplifier, it is necessary to apply the positive potential of 12 volts to the control input of the amplifier (REM
IN) through a switch or a corresponding control output (REMOTE OUT ) with the head unit (HU).
11 LED indicator on front of the amplifier turns . blue to indicate that the amplifier is turned on. If the indicator does not light
up see chapter "Possible faults and their solutions" for more information.
12. The sound level is calibrated by adjusting the volume of the source up to 3/4 of its maximum level. Then, adjust the
sensitivity level of the amplifier up until you hear distortions.
Thank you for purchasing of this Deaf Bonce product! Our company is committed to the creation of extremely loud sound
systems with no loss of quality.
To ensure proper use, please carefully read through this manual before using this product. It is especially important that you
read and observe caution’s in this manual. Please keep the manual in a safe and accessible place for future reference.
Termékspecifikációk
| Márka: | Edox |
| Kategória: | óra |
| Modell: | CO-1 Chronograph 10221-3-NIN |
Szüksége van segítségre?
Ha segítségre van szüksége Edox CO-1 Chronograph 10221-3-NIN, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók óra Edox
31 Augusztus 2024
31 Augusztus 2024
31 Augusztus 2024
31 Augusztus 2024
Edox Les Bémonts Ultra Slim Date Automatic 80114-37R-AIR Útmutató
31 Augusztus 2024
31 Augusztus 2024
31 Augusztus 2024
31 Augusztus 2024
31 Augusztus 2024
Edox Les Vauberts La Grande Lune Automatic 80500-3-AIBU Útmutató
31 Augusztus 2024Útmutatók óra
- óra Ikea
- óra Braun
- óra Nedis
- óra Oregon Scientific
- óra Garmin
- óra Lenovo
- óra Casio
- óra Auriol
- óra Emos
- óra Geemarc
- óra Camry
- óra Crivit
- óra Boss
- óra Omega
- óra Technaxx
- óra United Office
- óra Michael Kors
- óra Hama
- óra Renkforce
- óra Mitsubishi
- óra Techno Line
- óra Citizen
- óra Eta
- óra Trevi
- óra Fitbit
- óra Fisher Price
- óra Livoo
- óra Muse
- óra Suunto
- óra Pulsar
- óra ICE Watch
- óra Breitling
- óra Adidas
- óra Polar
- óra Tommy Hilfiger
- óra Kogan
- óra Alecto
- óra Velleman
- óra TFA
- óra McIntosh
- óra Eurochron
- óra Chacon
- óra Elro
- óra Jaguar
- óra Sempre
- óra TomTom
- óra Tissot
- óra Olympia
- óra Tronic
- óra Timex
- óra La Crosse Technology
- óra AKAI
- óra Konig
- óra GlobalTronics
- óra Pyle
- óra Alpina
- óra ECG
- óra Skmei
- óra Taylor
- óra Dormakaba
- óra Elation
- óra RCA
- óra Festina
- óra Beper
- óra Ascot
- óra Teesa
- óra Salter
- óra Topcom
- óra Fossil
- óra Lexon
- óra Vitek
- óra Zenith
- óra ART
- óra Fysic
- óra Ade
- óra Amplicom
- óra Accusplit
- óra Armani
- óra Invicta
- óra Alessi
- óra Lotus
- óra Lars Larsen
- óra Orient
- óra Jacques Lemans
- óra Calypso
- óra Bushnell
- óra Olivia Burton
- óra Victorinox
- óra Lambretta
- óra Tudor
- óra Holzkern
- óra Hublot
- óra Ebel
- óra Christopher Ward
- óra Gc
- óra So & Co
- óra Diesel
- óra Karlsson
- óra Bulova
- óra Lorus
- óra Stuhrling
- óra Easypix
- óra Swatch
- óra Luminox
- óra Emporio Armani
- óra Cresta
- óra Girard-Perregaux
- óra Certina
- óra TMI
- óra Detomaso
- óra Skagen
- óra Profile
- óra Marquant
- óra Jacob Jensen
- óra Dugena
- óra Rolex
- óra Seiko
- óra Perel
- óra AcuRite
- óra Ventus
- óra Technoline
- óra AV:link
- óra TW Steel
- óra Timberland
- óra Spinnaker
- óra Pilgrim
- óra Audiovox
- óra Davis
- óra Valcom
- óra Hager
- óra Habitat
- óra Clas Ohlson
- óra Zuiver
- óra Irox
- óra ELYSEE
- óra Danish Design
- óra Daniel Steiger
- óra Torgoen
- óra WoodWatch
- óra Executive
- óra Nautica
- óra Christiaan Van Der Klaauw
- óra Klaus Kobec
- óra Obaku
- óra Hugo Boss
- óra Shinola
- óra Gira
- óra Jung
- óra Spin Master
- óra Tikkers
- óra Krontaler
- óra Balance
- óra Sinn
- óra Brera
- óra Dexford
- óra Cover
- óra Lucien Picard
- óra Ranex
- óra Nike
- óra Swiza
- óra Mondaine
- óra IHome
- óra Slazenger
- óra Ticwatch
- óra Bering
- óra BBrain
- óra Leff
- óra DMC
- óra Lynx
- óra Maurice Lacroix
- óra Dakota
- óra La Crosse
- óra Rado
- óra Puma
- óra Gant
- óra Tauchmeister
- óra Westfalia
- óra Just
- óra IWC
- óra Digi-tech
- óra Freestyle
- óra Global Tronics
- óra ASA
- óra Misfit
- óra Breo
- óra BML
- óra Inter-Quartz
- óra Haffstreuner
- óra TFA Dostmann
- óra Hamilton
- óra Kalenji
- óra Longines
- óra Junghans
- óra Meister Anker
- óra Lydion
- óra GC Watches
- óra Speedo
- óra Naitica
- óra TCM
- óra Uri Minkoff
- óra Guess
- óra Antelope Audio
- óra Equity
- óra Mebus
- óra Hermle
- óra ESQ
- óra DB Technologies
- óra ETT
- óra Triwa
- óra Raketa
- óra Balmain
- óra Focus Electrics
- óra Wonky Monkey
- óra Audemars Piguet
- óra Timer
- óra Pyramid
- óra Marc Jacobs
- óra Iron Annie
- óra Julie Julsen
- óra Xonix
- óra KRAEK
- óra World Timer Chronograph
- óra Ferrari
- óra X-WATCH
- óra Versace
- óra PAUL HEWITT
- óra Rodania
- óra Bruno Sohnle
- óra Naviforce
- óra Gingko
- óra Movado
- óra Lacoste
- óra MICHELE
- óra Philip Watch
- óra QQ
- óra Fila
- óra Ronda
- óra Weinberger
- óra TimeStyle
- óra CyberData Systems
- óra Radley London
- óra PANERAI
- óra Prologue
- óra Zeppelin
- óra Hype
- óra Electronics International
- óra HYT
- óra Antelope
- óra Grand Seiko
- óra Bearware
- óra Fromanteel
Legújabb útmutatók óra
3 Április 2025
3 Április 2025
30 Március 2025
26 Március 2025
26 Március 2025
23 Március 2025
23 Március 2025
23 Március 2025
23 Március 2025
23 Március 2025