Használati útmutató Dürkopp Adler DAC eco M-Type
Dürkopp Adler
varrógép
DAC eco M-Type
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Dürkopp Adler DAC eco M-Type (94 oldal) a varrógép kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/94
DAC basic/classic
Instructions for use
Software version: B03.0
or later
All rights reserved.
Property of Dürkopp Adler GmbH and protected by copyright. Any reuse
of these contents, including extracts, is prohibited without the prior
written approval of Dürkopp Adler GmbH.
Copyright © Dürkopp Adler GmbH 2021
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of Contents
Instructions for use DAC basic/classic - 05.0 - 06/2021 1
1 About these instructions .................................................................... 3
1.1 For whom are these instructions intended? .......................................... 3
1.2 Representation conventions – symbols and characters ........................ 3
1.3 Other documents................................................................................... 5
1.4 Liability ..................................................................................................5
2 Technical specifications..................................................................... 7
2.1 Features ................................................................................................ 7
2.2 Declaration of Conformity...................................................................... 7
2.3 Additional equipment ............................................................................. 8
3 Safety.................................................................................................... 9
3.1 Basic safety instructions........................................................................9
3.2 Signal words and symbols used in warnings....................................... 10
4 Components and functions.............................................................. 13
4.1 Control................................................................................................. 13
4.2 Control panel ....................................................................................... 16
4.2.1 Display.................................................................................................17
4.2.2 Buttons ................................................................................................ 17
4.3 Setpoint device.................................................................................... 21
4.4 Proper use........................................................................................... 22
5 Operation ........................................................................................... 25
5.1 Basic operation.................................................................................... 25
5.1.1 Switching on and off the control .......................................................... 25
5.1.2 Using button groups ............................................................................ 27
5.2 Thread button group functions ............................................................ 27
5.2.1 Setting the start bartack ...................................................................... 28
5.2.2 Setting the multiple start bartack ......................................................... 29
5.2.3 Using the multiple start bartack as the darning program..................... 29
5.2.4 Setting the end bartack ....................................................................... 30
5.2.5 Setting the multiple end bartack .......................................................... 31
5.2.6 Activating the thread cutter.................................................................. 32
5.2.7 Activating the thread clamp.................................................................32
5.2.8 Setting the needle position after sewing stop ...................................... 32
5.2.9 Activating sewing foot lift after thread cutter........................................ 33
5.2.10 Activating sewing foot lift after sewing stop.........................................33
5.2.11 Activating soft start .............................................................................. 34
5.2.12 Reducing speed .................................................................................. 34
5.3 Programming button group functions .................................................. 35
5.3.1 Setting the bobbin piece counter......................................................... 35
5.3.2 Activating the bobbin stitch counter..................................................... 37
5.3.3 Setting the remaining thread monitor .................................................. 38
Table of Contents
Instructions for use DAC basic/classic - 05.0 - 06/20212
5.3.4 Activating the remaining thread monitor .............................................. 39
5.3.5 Activating the piece counter ................................................................ 40
5.3.6 Activating needle cooling..................................................................... 41
5.3.7 Setting the light barrier ........................................................................ 42
5.3.8 Activating the light barrier....................................................................45
5.4 Seam program button group functions ................................................ 45
5.4.1 Activating seam program I................................................................... 46
5.4.2 Activating seam program II.................................................................. 46
5.4.3 Setting seam program III ..................................................................... 47
5.5 Function button.................................................................................... 52
6 Troubleshooting ................................................................................ 55
6.1 Customer Service................................................................................ 55
6.2 Error messages ................................................................................... 55
7 Technical data ................................................................................... 57
8 Glossary ............................................................................................. 59
Technical specifications
Instructions for use DAC basic/classic - 05.0 - 06/20218
2.3 Additional equipment
A flexible system of additional equipment allows the control to be
optimally equipped for any application at low cost.
List of additional equipment
Part no. Additional equipment
DAC basic
DAC classic
9401 000454 Motor mount for undertable installation
9800 170038 Motor (4 Nm)
9800 170040 Motor (6 Nm)
9800 327007 Hall sensor
9800 347003 Synchronizer
9835 901005 Dongle
9850 001309 Machine ID
9870 001202 Cable for integrated sewing lamp
Safety
Instructions for use DAC basic/classic - 05.0 - 06/2021 9
3 Safety
This chapter contains basic information for your safety. Read the
instructions carefully before setting up or operating the control.
Make sure to follow the information included in the safety instruc-
tions. Failure to do so can result in serious injury and property
damage.
3.1 Basic safety instructions
The DAC basic/classic control may only be used as described
in these instructions.
The instructions should be available at the control's location at all
times.
Work on live components is prohibited.
The control was built and tested in compliance with all valid
ordinance and safety regulations, and left the factory in proper
working order.
The control will only work safely and reliably when the control is
used as intended ( 4.4 Proper use, p. 22).
Before leaving the workplace:
• Switch off the control
• Wait until the machine stops
• Wait until the LEDs go out
Obligations
of the operator Follow the country-specific safety and accident prevention regu-
lations and the legal regulations conce rning industrial safety and
the protection of the environment.
All warnings and safety signs on th e control must always be in
legible condition and may not be removed. Missing or damaged
labels must be replaced immediately.
Safety
Instructions for use DAC basic/classic - 05.0 - 06/202110
Requirements to
be met by the
personnel
The control may only be set up by specialists. Specialists are
persons with electronics and mechanical training.
The following work may only be performed by specialists.
• Maintenance work
• Repairs
• Work on electrical equipment
Only authorized persons may work on the machine. Anyone work-
ing on the machine belongs to the operators. Operators must have
read and understand the manual before working on the system.
Setup Control setup and start-up must be pe rformed carefully by qualified
technicians to ensure no health risks for operating personnel.
The connecting cable must have a power plug approved in the
relevant country. The power plug may only be connected to the
power cable by qualified specialists.
Operation Check the control while in operation for any externally visible
damage.
Stop working if you notice any changes. Report any changes to
your supervisor.
A damaged control should no longer be used.
Conversions or changes to the control are prohibited.
3.2 Signal words and symbols used in
warnings
Warnings in the text are distinguished by color bars. The color
scheme based on the severity of the danger. Signal words indicate
the severity of the danger:
Safety
Instructions for use DAC basic/classic - 05.0 - 06/2021 11
Signal words Signal words and the hazard they describe:
Symbols The following symbols indicate the type of danger to personnel:
Signal word Hazard
WARNING Performing an action can have se rious or hazardous
consequences.
CAUTION Performing an action can have undesirable
consequences, su ch as loss of data or damage
to hardware.
NOTICE Tips or more detailed information
to make operation easier for the user.
Symbol Type of danger
General danger
Electric shock
Puncture
Crushing
Environmental damage
Safety
Instructions for use DAC basic/classic - 05.0 - 06/202112
Examples Examples of the layout of warnings in the text:
This is what a warning looks like where non-compliance
could result in serious or hazardous consequences.
Th is is what a warning looks like where non-compliance
could result undesirable consequences, such as loss of data
or damage to hardware.
Th is is the more detailed information to simplify operation for
the user.
Type and source of danger!
Consequences of non-compliance.
Measures for avoiding the danger.
WARNING
Type and source of danger!
Consequences of non-compliance.
Measures for avoiding the danger.
CAUTION
Tip.
NOTICE
Components and functions
Instructions for use DAC basic/classic - 05.0 - 06/2021 13
4 Components and functions
When delivered the DAC basic/classic consists of:
• Control panel OP10 00
• Mounting parts
• Pedal rod
• Setpoint device
• DAC basic or DAC classic control
4.1 Control
The control is available in two different versions:
• DAC basic
• DAC classic
The DAC classic has more inputs and outputs in the back than
does the DAC basic.
Fig. 1: DAC basic/classic, front
(1) - Main switch
(2) - POWER LED
(3) - MESSAGE LED
(4) - Connection for dongle
(5) - Switch for sewing lamp
⑤
③
①
④
②
Components and functions
Instructions for use DAC basic/classic - 05.0 - 06/202114
Fig. 2: DAC basic, back
(1) - Connection for sewing motor
(2) - Connection for synchronizer
(3) - Connection for machine
(4) - Connection for machine ID
(5) - Connection for pedal
(6) - Connection for control panel
(7) - Connection for sewing motor-
encoder
②
①
③
⑥
⑦
⑤
④
Components and functions
Instructions for use DAC basic/classic - 05.0 - 06/2021 15
Fig. 3: DAC classic, back
(1) - Connection for sewing motor
(2) - Connection for synchronizer
(3) - Connection for CAN
(4) - Connection for additional input
(5) - Connection for machine
(6) - Connection for machine ID
(7) - Connection for pedal
(8) - Connection for control panel
(9) - Connection for sewing motor-
encoder
②
①
④
③
⑤
⑥
⑦
⑧
⑨
Termékspecifikációk
| Márka: | Dürkopp Adler |
| Kategória: | varrógép |
| Modell: | DAC eco M-Type |
Szüksége van segítségre?
Ha segítségre van szüksége Dürkopp Adler DAC eco M-Type, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók varrógép Dürkopp Adler
13 Október 2024
11 Október 2024
6 Október 2024
28 Szeptember 2024
15 Szeptember 2024
14 Szeptember 2024
3 Szeptember 2024
31 Augusztus 2024
31 Augusztus 2024
31 Augusztus 2024
Útmutatók varrógép
- varrógép Husqvarna
- varrógép SilverCrest
- varrógép Singer
- varrógép AEG
- varrógép Emerio
- varrógép Toyota
- varrógép Siemens
- varrógép Medion
- varrógép Carina
- varrógép Prixton
- varrógép Primera
- varrógép Tesco
- varrógép Ambiano
- varrógép Privileg
- varrógép Pfaff
- varrógép Brother
- varrógép Janome
- varrógép Solac
- varrógép Necchi
- varrógép Bernette
- varrógép Juki
- varrógép Livoo
- varrógép Guzzanti
- varrógép Baby Lock
- varrógép TriStar
- varrógép Kenmore
- varrógép Husqvarna-Viking
- varrógép Blaupunkt
- varrógép Easy Home
- varrógép Crofton
- varrógép Alfa
- varrógép Veritas
- varrógép Union Special
- varrógép Bernina
- varrógép Bestron
- varrógép Victoria
- varrógép EasyMaxx
- varrógép Anker-Bernette
- varrógép Sinbo
- varrógép Jata
- varrógép Elna
- varrógép Mellerware
- varrógép Termozeta
- varrógép Jocca
- varrógép Yamato
- varrógép Kayser
- varrógép RCE
- varrógép Lifetec
- varrógép Kunft
- varrógép Lervia
- varrógép Vendomatic
- varrógép Home Electric
- varrógép Empisal
- varrógép Lewenstein
- varrógép Durabase
- varrógép Meister Craft
- varrógép Micromaxx
- varrógép Yamata
- varrógép Weasy
- varrógép Łucznik
- varrógép Silver
- varrógép Prince
- varrógép Hofmann
- varrógép Kohler
- varrógép Muller
- varrógép Sinojo
- varrógép Huskystar
- varrógép Gritzner
- varrógép LERAN
- varrógép W6
- varrógép Zippy
- varrógép Feiyue
- varrógép Mediashop
- varrógép ER
- varrógép Novamatic
- varrógép Siemssen
- varrógép Mio Star
- varrógép SteamMax
Legújabb útmutatók varrógép
15 Január 2025
14 Január 2025
14 Január 2025
14 Január 2025
13 Január 2025
12 Január 2025
12 Január 2025
12 Január 2025
12 Január 2025
12 Január 2025