Használati útmutató DLS CAD 15
DLS
Autórádió/CD lejátszó
CAD 15
Olvassa el alább 📖 a magyar nyelvű használati útmutatót DLS CAD 15 (12 oldal) a Autórádió/CD lejátszó kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/12
How to install and operate
the
DLS CAD11
&
DLS CAD15
digital mono amplifiers
Welcome!
This owners manual is written in easy english and
uses a lot of drawings to simply the installation and
use of the above amplifier.
Your DLS amplifier must be installed correctly in or-
der to work well. This manual will show you how to
install the amplifier like a pro. Please read the entire
manual before beginning the installation.
Install the amplifier yourself if you feel confident with
our instructions and if you have the proper tools.
However if you feel unsure, turn over the installa-
tion job to someone better suited to it.
Warranty Service
This amplifier is covered by warranty, depending
on the conditions in the country where it is sold. If
the amplifier is returned for service, please include
the original dated receipt with the product.
Technical Assistance
For technical assistance ask the shop where the
product was sold or the distributor in your very coun-
try.
You can always phone the DLS Helpdesk in Sweden
+ 46 31 84 00 60 or send an e-mail to info@dls.se.
Information can also be found on our WEB-site
www.dls.se
Contents
Specifications................................ 1
Features…………………………….. 2
Installation…………………….……. 2
Tools and materials needed………. 3
Amplifier installation kit………….... 3
Routing Wires…………………….... 3
Wiring
Power and Outputs……………..…. 4
Inputs and controls………………... 5
Input level control.......................... 5
Crossovers…………...................... 5
Phase control.....………………...… 5
Bass boost control......................... 6
Remote bass level control............. 6
Speaker wiring:
Single amplifier system………….…. 6
Testing............................................. 6
Bridging two CAD11......................... 7
Bridging two CAD15........................ 8
Subwoofer connections…………….. 9
Professional tips............................... 10
Technical data.................................. 11
Trouble shooting.............................. 11
DLS Svenska AB
P.O. Box 13029
S-40251 Göteborg, Sweden
Tel: +46 31 840060
Fax: +46 31 844021
E-mail: info@dls.se
www.dls.se
DLS Svenska AB - 2007-01-10
We follow a policy of continuous advancement in
development. For this reason all or part of specifications
& designs may be changed without prior notice.
Approval of electromagnetic compatability according
to the EEC Directive 95/54/EC
E 13 CAD15 approval No: 022944
CAD11 approval No: 022495
CAD11 &15 include
RCA input and output
High level input with auto start
Continuous variable low pass crossover
Continuous variable subsonic crossover
Bass boost feature
Remote bass level control
Phase control cont. variable 0-180 degrees
Bridge mode master / slave selector
Electronic protection circuitry against
short-circuit, DC offset and thermal overload.
Installation
Before you begin the install
Before you begin you need to read the manual, to have
some tools, cables and other material available. There
is one such list of material on the following page.
Amplifier location
Important
Allow air circulation around the amplifier.
2
Disconnect Battery
Before starting the instal-
lation, always disconnect
the negative terminal of
the battery.
The DLS Peformance series of amplifiers have a
compact design that allows great flexibility in
mounting. You can mount it under a seat or in the
trunk.
When you select a location, do remember that the
amplifier generates a lot of heat.
Choose a location where air can circulate freely
around the amplifier. Do not cover the amplifier with
carpets or hide behind trim panels.
Do not mount the amplifier in an inverted or upside
down position.
Check all locations and placements carefully before
making any cuts, drilling any holes or making any
connections.
This is the best direction to
mount the amplifier to get
the best cooling.
CAD11, CAD15
DLS logo on amplifier cooling flange
The DLS logo on top of the amplifier is attached
with two hex. screws. The logo can be removed
and twisted 90 or 180 degrees, and then screwed
back in wanted position. The logo can be mounted
in four different ways to match your installation.
Removal of side flanges
In order to fasten the amplifier to the surface and
connect speaker and power cables, the flanges on
the sides must be removed. This is done by
loosening the hex screws on top of the amplifier.
Use a 3 mm hex key.
Remove these
screws using a 3
mm hex. key for
removal of side
flange. Remount
after fastening the
amplifier and
connection of the
speaker and power
cables.
Tools and material needed
Tools:
Flat and Phillips screwdrivers
Wire cutter
Wire stripper
Electric drill with drills
Crimping tool
Digital multimeter or test lamp
Wire brush, scraper or a piece
of an abrasive sheet to remove
paint for a good ground connection
Grease to protect the ground
connection from corrosion
Material:
Speaker wire: minimum
12 AWG = 4 mm2 for subwoofers
Sheet metal screws for mounting the
amplifier to the amplifier board and the
amplifier board to the car + some extra
for fuse holder, amplifier ground etc.
Electrical insulation tape
½ inch thick plywood or particle board for
the amplifier to be mounted upon.
Amplifier installation kit:
If available,buy an amplifier installation kit. It
contains normally all you need. This is what you
have to buy if you buy the items separately
20- 25 feet = 6- 7.5 meter power cable,
preferably AWG 0 (50 mm2 ) for CAD15 &
4AWG (21mm2) for CAD11
1 pc of ANL fuseholder to install close to the
car battery + fuse. CAD11= 150A, CAD15=
200A
20 feet of AWG 15 = 1,5 mm2 wire for
remote turn on / off cable from radio.
RCA-cable for input from radio.
- 20 feet or 5 meter for trunk installations
-12 feet or 2 – 3 meter for under seat
installations
One ring crimp terminal
for the amplifier ground connection.
Wire ties
Insulating grommet or insulating tube
Routing wires
Stereo
head unit
3
Professional Tip:
If amplifier installation kits are available with diffe-
rent size of power cable, chose the most heavy
power cable to improve sound quality and to allow
more amplifiers to be installed now or later.
If possible buy AWG 0 = 50 mm2 (or heavier) cable
for best performance of CAD15, or AWG4 (21 mm2)
for CAD11.
High current draw
The CAD11 / 15 are mono amplifiers with high power
output. The current draw is also high so you must make
sure that your vehicles power system (battery and
alternator) can provide all the power you need. If you
have a bad battery or alternator in can result in a poor
sound or even worse, a broken battery or alternator.
CAD11, CAD15
Termékspecifikációk
| Márka: | DLS |
| Kategória: | Autórádió/CD lejátszó |
| Modell: | CAD 15 |
Szüksége van segítségre?
Ha segítségre van szüksége DLS CAD 15, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Autórádió/CD lejátszó DLS
23 Augusztus 2024
23 Augusztus 2024
22 Augusztus 2024
22 Augusztus 2024
22 Augusztus 2024
22 Augusztus 2024
22 Augusztus 2024
Útmutatók Autórádió/CD lejátszó
- Autórádió/CD lejátszó Sony
- Autórádió/CD lejátszó Grundig
- Autórádió/CD lejátszó Pioneer
- Autórádió/CD lejátszó JVC
- Autórádió/CD lejátszó AEG
- Autórádió/CD lejátszó Kenwood
- Autórádió/CD lejátszó Alpine
- Autórádió/CD lejátszó AKAI
- Autórádió/CD lejátszó Rockford Fosgate
- Autórádió/CD lejátszó Marquant
- Autórádió/CD lejátszó Audiovox
- Autórádió/CD lejátszó Mx Onda
- Autórádió/CD lejátszó Lanzar
- Autórádió/CD lejátszó Fusion
- Autórádió/CD lejátszó Axton
- Autórádió/CD lejátszó Soundstream
- Autórádió/CD lejátszó VDO Dayton
- Autórádió/CD lejátszó Becker
- Autórádió/CD lejátszó Helix
- Autórádió/CD lejátszó Toxic
- Autórádió/CD lejátszó Eclipse
- Autórádió/CD lejátszó Belson
Legújabb útmutatók Autórádió/CD lejátszó
20 Szeptember 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
22 Augusztus 2024